2004 honda pilot 3.5 timing marks


You are searching repair manual in PDF format about 2004 honda pilot 3.5 timing marks use another keyword for search another post or files



  2004 honda pilot 3.5 timing marks Direct Download speed 5787 Kb/s

  2004 honda pilot 3.5 timing marks Full Version speed 6767 Kb/s




2003 TOYOTA TACOMA TIMING BELT INSTALLATION REMOVAL

0

Filed Under (Toyota) by admin on 13-01-2011

download
NOTICE: Always turn the crankshaft clockwise. (c) Check that the timing marks of the camshaft timing pul- leys and No.3 timing belt cover are aligned. If not, turn the crankshaft pulley 1 revolution (360°). (d) Remove the crankshaft pulley bolt. IF REUSING TIMING BELT, CHECK INSTALLATION MARKS ON TIMING BELT Check that there are 3 installation marks and front mark on the timing belt. If the installation and front marks have disappeared, before re- moving the timing belt, place 3 new installation marks on the timing belt to match the timing marks of the timing pulleys, and place a new front mark on the timing belt. 18. 19. REMOVE TIMING BELT TENSIONER Alternately loosen the 2 bolts, and remove them, the belt ten- sioner and dust boot. 20. REMOVE TIMING BELT 21. (a) REMOVE RH CAMSHAFT TIMING PULLEY Using SST, loosen the pulley bolt. SST 09960–10010 (09962–01000, 09963–01000) Remove the bolt, knock pin and timing pulley. (b) 22. (a) REMOVE LH CAMSHAFT TIMING PULLEY Using SST, loosen the pulley bolt. SST 09960–10010 (09962–01000, 09963–01000) Remove the bolt, knock pin and timing pulley. (b) 23. REMOVE NO.2 IDLER PULLEY Remove the bolt and idler pulley. 24. REMOVE NO.1 IDLER PULLEY Using a 10 mm hexagon wrench, remove the pivot bolt, idler pulley and plate washer. 25. REMOVE CRANKSHAFT TIMING PULLEY Remove the timing pulley. HINT: If the pulley cannot be removed by hand, use SST and a service bolt to remove the timing pulley. SST 09950–50011 (09951–05010, 09952–05010, 09953–05020, 09954–05011)

Related entry:

yhs-fullyhosted_003, 1998 cadillac catera timing marks, 2002 xterra timing marks, timing marks on 2007 suzuki forenza, 2003 hyundai accent cam timing marks, Timing nissan NA20 engine on YouTube, timing on a 1994 nissan 2400 12 valve engine, 2004 Chrysler Pacifica can you still be at top dead center and cranky and still be off the compression stroke, remove and install a 1998 toyota camry timing belt, HOW TO SET TIMING ON 2005 DODGE SLT 3 7 LITER VIDEO,

Door Panel Removal Honda Odyssey & 2003-2006 Honda Pilot

0

Filed Under (Honda) by admin on 02-06-2010

download
Honda Odyssey & 2003-2006 Honda Pilot 2007 & 2008 Honda Pilot – Door panel removal procedures are different from previous models – see page 4. Open the driver side door and lower the window. Remove the door panel, kick panel, and plastic trim piece along the bottom of the door frame. 1) Open the driver side door and lower the window. Using a plastic pry bar, carefully remove corner trim. 2) Remove plastic cover in door release lever to reveal 2-screws. Remove these screws with a Phillips screwdriver. 3) Pry loose the control panel. Disconnect all wiring connections behind control panel and remove control panel. Remove the revealed screw behind control panel. 4) Remove screw hidden below the grab bar. Carefully pull on door panel until all snap inserts, around the perimeter of door panel, pop loose. 5) Hold door panel slightly away from door frame. Disconnect all wiring connections behind door panel. 6) Remove release lever rod from behind door panel. Remove and set aside door panel.

Related entry:

honda pilot alternator removal, 2006 Honda Odyssey Alternator Removal, chilton manual honda pilot 2005 fuse panel diagram, honda odysssey 2007 obd port, how to reove tailgate panel on hoda 2002 crv, 2007 honda pilot thermostat replacement, how to remove inner panel on tail gate of 2007 honda odyssey, 2011 honda pilot hatch door panel, how to remove tailgate trim honda odyssey 2005, heater control removel 2005 honda pilot,

1996 Chevrolet Monte Carlo Camshaft Timing COMPLETE CAM TIMING PROCEDURE

0

Filed Under (Chevrolet) by admin on 10-08-2010

download
T] EXHAUST CAMSHAFT (RIGHT) T| INTAKE CAMSHAFT (RIGHT) T] SECONDARY TIMING BELT IDLER PULLEYS T) INTAKE CAMSHAFT (LEFT) 7] EXHAUST CAMSHAFT (LEFT) T] COOLANT PUMP T] INTERMEDIATE SHAFT BELT SPROCKET T] SERPENTINE BELT TENSIONER T| SECONDARY TIMING BELT TENSIONER PULLEY ??] GENERATOR ??] SECONDARY TIMING BELT TENSIONER ?2? SECONDARY TIMING BELT NOTE: START AT #7 AND INSTALL COUNTERCLOCIOMBE A LOCATION OF TIMING MARKS WITH CAM HOLD DOWN TOOLS J 38813 INSTALLED B FRONT COVER TIMING MARK C LOCATION OF TIMINS MARKS WITH DRIVE BELT IN- STALLED D LOCATION WHERE CAM HOLD DOWN TOOLS ARE INSTALLED RH EXHAUST CAMSHAFT SPROCKET RH INTAKE CAMSHAFT SPROCKET LH INTAKE CAMSHAFT SPROCKET LH EXHAUST CAMSHAFT SPROCKET PERMANENT MARKS PAINTED DOTS REMOVE PREVIOUS MARKS IF TIMING IS BEINS CHANGED AND MARK AGAIN IN THESE LOCATIONS TORSIONAL DAMPER INTERMEDIATE SHAFT SPROCKET NOTE: THIS TDC #1 EXHAUST. INTtRMEDlATE »HAFT BELT sprocket twno mark» at » o’clock (powtmo towards drain notch) NOTE : GM does not provide a timing mark diagram for belt installation without using the special tool(s) listed below. TOOLS REQUIRED: A J 38613 CamHold Down Tool A J 38614 Cam Sprocket Holding Tool NOTICE: If only one (1) bank is to be timed, make sure bank to bank earn timing relationship is one (1) revolution apart. Timing flats should be 180 degrees opposite (right bank versus left bank) when finally timed. 1. Remove all spark plugs. 2. Remove all camshaft sprockets. IMPORTANT: Remove oil from cam hold down tool bolt hole in carrier before installing and tightening bolt. 3. Rotate camshaft flats “up” and install J 38613. Tighten cam hold down tool bolt to 30 Nm (22 lb. ft). 4. Install all camshaft sprockets. 5. Timing belt by routing it around the idlers and sprockets. DO NOT bend, kink, or pry on belt as damage may occur. A. Start at intermediate cam sprocket and work counterclockwise. B. Make sure the belt is installed in direction of rotation. C. Engage teeth into all sprockets, place rubber hose behind belt at intermediate sprocket and accumulate slack at tensioner location. 6. Tensioner pulley to mounting base. A Use flat magnet, tape or cup plug to hold pivot tube in pulley during this step. Otherwise, pivot tube may fall out. A After starting pivot bolt, rotate arm counterclockwise to position square lug at 6 o’clock

Related entry:

4 3 vortec timing procedure, cam setting for 1996 toyota cambry, NISSAN 1400 TIMING MARKS, timimg marks for a 2 0 tdi 16 valve vw, 2004 lincoln navigator timing marks, How to set nissan sentra 16v 160 chain timming guide, 1996 toyota rav4 ford camshaft alignment tool, vw rabbit mk1 cam timing, colt club cab 2 8 tdi timing chain, how to set camshafts and timing marks on 3S FE engine,

1996 Mitsubishi Eclipse GS-T TIMING BELT & BALANCE SHAFT BELT Removal

0

Filed Under (Mitsubishi) by admin on 18-01-2011

download
1. Disconnect negative battery cable. Remove engine undercover. Place wooden block between jack and oil pan, and raise engine slightly. Remove engine mount assembly near timing belt cover. 2. Remove clamp for power steering return hose near timing belt cover. Remove all drive belts and tensioner pulley bracket. See Fig. 1 . Remove power steering and water pump pulleys. Rotate crankshaft clockwise so that No. 1 cylinder is at TDC of compression stroke. Remove crankshaft pulley. CAUTION: DO NOT rotate crankshaft counterclockwise. Ensure timing marks are aligned. If reusing timing belts, mark timing belts for direction of rotation. 3. Remove upper timing belt cover and gasket. Remove stub bolt of engine support bracket, and remove center timing belt cover. Remove lower timing belt cover. NOTE: Camshaft sprocket dowel pins will be in 12 o’clock position when timing marks are correctly aligned. 4. Ensure camshaft, crankshaft and oil pump sprocket timing marks are aligned. See Fig. 2 or Fig. 3 . Loosen tensioner pulley center bolt. Move tensioner to relieve timing belt tension. Remove timing belt. Remove timing belt auto tensioner. See Fig. 1 . 5. Remove plug from left side of cylinder block. Install a .31″ (8.0 mm) diameter Phillips screwdriver into the hole against balance shaft. See Fig. 4 . Screwdriver must go in at least 2.36″ (60 mm) or more. If screwdriver will only go in about .79-.98″ (20-25 mm) before striking balance shaft, turn sprocket one revolution and align timing mark. Keep screwdriver in place until timing belt is installed. This ensures balance shaft driven by oil pump sprocket remains in correct position. 6. To remove timing belt “B” (balance shaft belt), hold crankshaft sprocket stationary with a spanner wrench. Remove crankshaft sprocket bolt. Using gear puller, remove outer crankshaft sprocket. 7. Remove crankshaft sensing blade (if equipped). See Fig. 5 . Loosen timing belt “B” tensioner bolt. If reusing timing belt “B”, mark direction of belt rotation for reassembly reference. Remove timing belt “B”.

Related entry:

water pump replacement 1992 mitsubishi 4g64 sohc video, 1992 mitsubishi 4g64 engine balance shaft belt replacement, 1996 toyots rave 4 timing marks, 1997 Honda Accord LX 4 cylenda Timming belt marks, camshaft sprocket removal mitsubishi 4g64 1992 8v, vw bkp balance shaft timing procedure, water pump replacement 1992 mitsubishi 4g64 sohc, 2007 triton v6 timing belt, picture 1992 mitsubishi 4g64 sohc crankshaft sprocket, 2 2 ecotec balnce shft timing,

1999 Daewoo Nubira SX TIMING BELT REMOVAL & INSTALLATION

0

Filed Under (Daewoo) by admin on 05-04-2011

download
Removal 1. Disconnect negative battery cable. Disconnect intake air temperature sensor connector from intake air duct. Disconnect the air intake tube from the throttle body. Disconnect the breather tube from the valve cover. Remove the air filter housing. 2. Raise and support the vehicle. Remove right front wheel. Remove right front splash shield from wheelwell. Remove serpentine accessory drive belt. 3. Remove crankshaft pulley bolts. It is NOT necessary to remove crankshaft sprocket center bolt. Remove crankshaft pulley. Lower vehicle. 4. Support engine assembly from above with Support Fixture (J-28467-B). See Fig. 1 . Remove engine mount bracket from timing belt end of engine. See Fig. 2 . 5. Remove front timing belt cover. Using crankshaft center bolt, rotate crankshaft one full turn clockwise (as viewed from timing belt end of engine). 6. Align mark on crankshaft sprocket with notch at bottom of rear timing belt cover. See Fig. 3 . Align camshaft sprocket timing marks with notches on valve cover. See Fig. 4 . CAUTION: Engine damage could result if camshaft sprockets are not properly aligned with notches on valve cover. 7. Loosen the automatic tensioner bolt. Use an Allen wrench to rotate tensioner and relieve tension on timing belt. See Fig. 5 . Remove timing belt. Installation 1. Ensure crankshaft and camshaft timing timing marks are still aligned. Install the timing belt. See Fig. 6 . Turn the timing belt tensioner clockwise to tension the timing belt. Turn tensioner until the pointer aligns with the notch on the rear timing belt cover. Tighten automatic tensioner bolt. See TORQUE SPECIFICATIONS . 2. Using crankshaft center bolt, turn crankshaft clockwise (as viewed from timing belt end of engine) 2 full revolutions. Ensure timing belt tensioner pointer is still aligned with notch. 3. If timing belt tensioner is correctly aligned, install timing belt cover. Install the engine mount bracket on the timing belt end of engine. Install crankshaft pulley. Install serpentine accessory drive belt. Install right front splash shield. Install right front wheel. 4. Install air filter housing. Connect air intake temperature sensor connector. Connect negative battery cable.

Related entry:

99 5 4 triton timing procedure, 07 mazda cx7 ac stops when deiving, timming belt tensioner loosening on a 99 neon rt 2 0 dohc, timing marks 1999f150 with4 6, pic of new timing belt tensioner setting on the 2002 daewoo nubira 2 0 dohc, Ford 3 8 Timing Cover Removal, 2001 daewoo nubira top dead center diagram, 1999 saturn sc1 sohc engine timing marks, 1999 ford 5 4 timing, where is the timing marks on 1999 volkswagen beetle,