2004 mercury grand marquis free wiring schematic


You are searching repair manual in PDF format about 2004 mercury grand marquis free wiring schematic use another keyword for search another post or files




1989-2006 Mercury Grand Marquis Ford Crown Victoria Lincoln Town Car DISABLING OF AIR SUSPENSION CONTROLS

0

Filed Under (Ford) by admin on 15-08-2010

download
Air suspension switch in trunk area must be turned o . On 1991-94 vehicles, locate the control module for the air suspension in the trunk area on either the back of rear seat or behind the trim panel on the right rear side of the trunk. On 1995-97 vehicles the control module is located under the right side of dash panel. There are 2 connectors for all model years, 1 black and 1 gray. On the 98-06 leave the solenoid connected. Disconnect the black connector and remove or cut the wire to pin #11 as shown. This will turn o the “AIR SUSP” message on the dashboard. The color code for this wire should be as follows: LINCOLN TOWN CAR: dark green/light green CROWN VICTORIA: green MERCURY GRAND MARQUIS: green Reconnect the black connector to the control module. This connector must be reconnected as the control module also controls functions of the “EVO” steering system. Turn Suspension Switch ON. NOTE: The parts in this kit are designed to replace the worn or nonfunctioning original equipment parts in the vehicle as produced by the car factory. These parts are not designed for installation on vehicles where the suspension aand/or steering systems have been modified for racing, competition, or any other reason than originally designed by manufacturer.

Ford Crown Victoria, Mercury Grand Marquis Repair Manual 1988-2000

0

Filed Under (Ford) by admin on 31-08-2009

repair and service manual covers all fuel-injected Ford Crown Victoria and Mercury Grand Marquis models, from 1988 through 2000. Note: this manual does not contain information specific to carbureted versions, 5.8L V8 engine, or natural-gas-fueled vehicles.
What’s Inside
Introduction: Vehicle identification numbers; Buying parts; Maintenance techniques, and more. Tune-up and routine maintenance; Engine and overhaul procedures; Cooling, heating and air-conditioning systems; Fuel and exhaust systems; Engine electrical systems; Emissions control systems; Transmission; Brakes; Suspension and steering systems; Body; Chassis electrical system; Wiring diagrams.

Audi A4 Sedan 2002-2004, Audi A4 Avant 2002-2004, Audi A4 Cabriolet 2003-2004 – 1.8 Liter 4-Cyl. 5V Turbo Generic Scan Tool

0

Filed Under (Audi) by admin on 15-09-2009

Check the following wire connection for open circuit according to wiring diagram:Relay carrier in E-box, plenum chamber, position 3Terminal Harness connector atignition coils Terminal 8 1 Specified value: Wire resistance max 1.5 – If necessary, repair wire connection. Audi A4 Sedan 2002-2004, Audi A4 Avant 2002-2004, Audi A4 Cabriolet 2003-2004 – 1.8 Liter 4-Cyl. 5V Turbo Generic Scan Tool, Engi…Page 5 24-158 If no malfunctions are found in wires: – Check voltage supply of Motronic Engine Control Module (ECM) voltage supply relay – J271 – Page 24-158 . – Check activation of Motronic Engine Control
Module (ECM) voltage supply relay – J271 – Page 24-159 . Checking voltage supply If specified value is not obtained:
- Connect multimeter for voltage measurement as follows. Relay carrier in E-box, plenum chamber, position 3
Terminal

ENGINE MISFIRE 2003-2004 Mustang, 1999-2004 Navigator 2002-2003 Blackwood 2003-2005 Aviator 2003-2004 Marauder

0

Filed Under (Ford) by admin on 11-05-2010

download
Some 1999-2004 Navigator, 2002-2003 Blackwood, 2003-2005 Aviator, 2003-2004 Marauder and 2003-2004 Mustang vehicles built before 12/19/2004 equipped with 4.6L 4V/5.4 4V engine may exhibit a runs rough, lacks power, and engine misfire, prompted by a MIL light and DTC codes P0301, P0302, P0303, P0304, P0305, P0306, P0307, P0308, and P0316. ACTION Diagnose engine for engine misfire concern. If diagnostics determine an engine misfire which is characterized by leakage through exhaust valve(s), only replace the affected cylinder head(s). SERVICE PROCEDURE

2004 Hyundai Sonata 2003-2004 Hyundai Santa FE 2004 Kia Optima no spark Problem and Repair

0

Filed Under (Hyundai) by admin on 25-04-2010

download
1. At the crank position sensor, check for battery voltage to be present on the Red wire with the key on and cranking. The Black wire should be a good ground and the Blue wire should have 5 volts on it from the computer. One may have to disconnect the crank sensor to check for the 5 volt reference. 2. During crank look for a good 5 volt square wave signal on the Blue wire. 3. Check at the ignition coils for good battery voltage key on and cranking. If there is a loss of voltage during crank check the ignition failsafe relay. 4. Check for any stored engine codes. Crankshaft Position (CKP) Sensor Ignition Failsafe Sensor The ignition failsafe sensor supplies battery voltage to the ignition coils. The ignition coils can look like they have good battery voltage key on but during crank the ignition failsafe relay can stop sending voltage to the ignition coils.