Auto Repair Manual Free Download and ReviewsFree download ebook pdf files automotive manual

download
1. Vehicle Disassembly. (a) Remove the negative battery cable. (Fig. 1-1) (1) Protect the fender before starting. (2) Do not touch the positive terminal withany tool removing the cable. (b) Remove the glove box under-dash cover. (Fig. 1-2) (c) Remove the passenger’s step cover. (Fig. 1-3) Fig. 1-1 10mm Wrench Negative Battery Cable Battery Step Cover Fig. 1-3 Nylon Panel Removal Tool Fig. 1-2 Under-Dash Cover Nylon Panel Removal Tool Page 3 TOYOTA AVALON 2005 – TVIP V4 (REMOTE ENGINE STARTER) Procedure Page 3 of 33 pages Issue: C 02/02/05 (d) Remove the passenger’s cowl cover. (Fig. 1-4) (1) Remove one nut securing the cowl cover. (e) Remove one screw and one bolt from the glove box assembly. (Fig. 1-5) (f) Remove the glove box assembly. (Fig. 1-6) (1) Open the glove box door and remove three screws securing the glove box assembly. (2) Disconnect the trunk opener cancel switch from the glove box assembly ifequipped. For vehicles with Smart Entry, the disassembly process ends on Step f. Go to Section 5. For vehicles without Smart Entry, continue the disassembly process

download
Removal and Installation WARNING: When carrying out maintenance on the starting system be aware that the heavy gauge leads are connected directly to the battery. Make sure the protective caps are in place when maintenance is completed. Failure to follow these instructions may result in personal injury. 1. With the vehicle in NEUTRAL, position it on a hoist. 2. Disconnect the battery ground cable. 3. Remove the nut and disconnect the starter solenoid S-terminal eyelet. To install, tighten to 6 Nm (53 lb-in) . 4. Remove the nut and disconnect the starter solenoid B-terminal eyelet. To install, tighten to 12 Nm (9 lb-ft) . 5. Remove the nut and disconnect the starter motor ground cable eyelet. To install, tighten to 20 Nm (15 lb-ft) . 6. Remove the stud bolt, the bolts and the starter motor. To install, tighten to 25 Nm (18 lb-ft) . 7. NOTE: Tighten the upper bolt before tightening the lower fasteners. To install, reverse the removal procedure.

WIRING INFORMATION: 2002 Chevy Trailblazer WIRE  WIRE COLOR WIRE LOCATION 12V CONSTANT WIRE RED and RED/WHITE Ignition Harness STARTER WIRE YELLOW Ignition Harness IGNITION WIRE PINK Ignition Harness SECOND IGNITION WIRE
WHITE Ignition Harness ACCESSORY WIRE ORANGE Ignition Harness SECOND ACCESSORY WIRE BROWN Ignition Harness KEYSENSE WIRE (-)
LT.GREEN Ignition Harness POWER DOOR LOCK POWER DOOR UNLOCK On these vehicles, door locks are controlled by a data bus system. This requires interfacing the door locks in several locations (each of the front doors, the rear hatch, and the fuse box under the rear seat) or using a databus interface module made specifically for this vehicle

download

WIRING INFORMATION: 2003 Cadillac Escalade ESV WIRE WIRE COLOR
WIRE LOCATION 12V CONSTANT WIRE RED Ignition Harness STARTER WIRE YELLOW Ignition Harness IGNITION WIRE PINK Ignition Harness SECOND IGNITION WIRE WHITE Ignition Harness This wire MUST be energized when installing a remote start system otherwise a CHECK ENGINE light will turn on and the transmission will not shift properly and the transmission may be damaged

download

WIRING INFORMATION: 2005 Chrysler 300C WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT WIRE Must go to battery for 12V constant.
STARTER WIRE PINK/DK.GREEN Ignition Harness SECOND STARTER WIRE PURPLE/BROWN Ignition Harness The second starter wire is negative trigger through a 180-ohm resistor. IGNITION WIRE PINK/WHITE Ignition Harness

download