2005 ford e350 vacuum pump removal


You are searching repair manual in PDF format about 2005 ford e350 vacuum pump removal use another keyword for search another post or files



  2005 ford e350 vacuum pump removal Direct Download speed 5787 Kb/s

  2005 ford e350 vacuum pump removal Full Version speed 6767 Kb/s




2004 Jeep Grand Cherokee Limited DIAGNOSIS AND TESTING – VACUUM RESERVOIR

0

Filed Under (Jeep) by admin on 18-11-2010

download
1. Disconnect vacuum hose at speed control servo and install a vacuum gauge into the disconnected hose. 2. Start engine and observe gauge at idle. Vacuum gauge should read at least ten inches of mercury. 3. If vacuum is less than ten inches of mercury, determine source of leak. Check vacuum line to engine for leaks. Also check actual engine intake manifold vacuum. If manifold vacuum does not meet this requirement, check for poor engine performance and repair as necessary. 4. If vacuum line to engine is not leaking, check for leak at vacuum reservoir. To locate and gain access to reservoir, refer to Vacuum Reservoir REMOVAL /INSTALLATION . Disconnect vacuum line at reservoir and connect a hand-operated vacuum pump to reservoir fitting. Apply vacuum. Reservoir vacuum should not bleed off. If vacuum is being lost, replace reservoir. 5. Verify operation of one-way check valve and check it for leaks. a. Locate one-way check valve. The valve is located in vacuum line between vacuum reservoir and engine vacuum source. Disconnect vacuum hoses (lines) at each end of valve. b. Connect a hand-operated vacuum pump to reservoir end of check valve. Apply vacuum. Vacuum should not bleed off. If vacuum is being lost, replace one-way check valve. c. Connect a hand-operated vacuum pump to vacuum source end of check valve. Apply vacuum. Vacuum should flow through valve. If vacuum is not flowing, replace one-way check valve. Seal the fitting at opposite end of valve with a finger and apply vacuum. If vacuum will not hold, diaphragm within check valve has ruptured. Replace valve.

Related entry:

algo-charter_if, 1978 Corvette Vacuum Hose Diagram, 1994 ford e150 a/c vacuum diagram, how to replace vacuum ressevoir e350 van, yhs-d2s_a, 2005 ford explorer vacuum line routing, 2004 chevy impala vacuum hose line, vaccum chamber 1992 chev van ebay, schematic of bmw N54 engine, how to check a/c vacuum lines neon 2 0,

1994 Mercury Villager Water Pump REMOVAL AND INSTALLATION

0

Filed Under (Mercury) by admin on 03-04-2011

download
Water Pump Removal 1. Drain the cooling system. Refer to Section 03-03. 2. Disconnect the battery ground cable (14301) . 3. Remove the generator drive belt, water pump and power steering pump drive belt, and the A/C compressor drive belt (if equipped). Refer to Section 03-05. 4. Raise and support the vehicle. 5. Use Strap Wrench D85L-6000-A or equivalent to hold the water pump pulley (8509) while removing the four water pump pulley bolts. 6. Remove the water pump pulley from the water pump (8501) . 7. Remove the crankshaft pulley (6312) . Refer to the procedure in this section 8. Remove the five lower engine front cover bolts and the lower engine front cover (6019) . NOTE: Make a note of the location of the one water pump bolt with the threads in the bolt head for ease of installation. 9. Remove the six water pump bolts. 10. Remove the water pump . Installation NOTE: Ensure the mating surfaces between the water pump and the cylinder block (6010) are cleaned of any sealant material. 1. Install a continuous 2.0-3.0mm (0.079-0.118 inch) wide bead of Gasket Maker E2AZ-19562-B or equivalent meeting Ford specification WSK-M2G348-A5, on the water pump and position the water pump on the cylinder block . NOTE: Refer to the note made during removal for the location of the bolt with the threads in the bolt head. 2. Install the six water pump bolts. Tighten the water pump bolts to 16-21 Nm (12-15 lb-ft). 3. Install the crankshaft pulley . Refer to the procedure in this section. 4. Position the water pump pulley on the water pump and install the four water pump pulley bolts. 5. Use Strap Wrench D85L-6000-A or equivalent to hold the water pump pulley , and tighten the four water pump pulley bolts to 16-21 Nm (12-15 lb-ft). 6. Install the lower engine front cover and the five lower engine front cover bolts. Tighten the five lower engine front cover bolts to 3-5 Nm (27-44 lb-in). 7. Lower the vehicle. 8. Install and adjust the generator drive belt, water pump and power steering pump drive belt, and the A/C compressor drive belt (if equipped). Refer to Section 03-05. 9. Connect the battery ground cable . 10. Fill the cooling system. Refer to Section 03-03. 11. Start the engine (6007) and check for leaks.

Related entry:

2002 MERCURY SABLE WATERPUMP REPLACEMENT, how to remove vacuum pump and pully for a 1993 ford e 350 7 3, how to remove pulley on water pump of a 2003 cts, how to install a water pump drive belt on a 2009 ford escape, how to change a radiator on a 2002 mercury cougar, how instal td27 injector pump, 4 6 northstar water pump diagram, 2008 ford escape water pump belt replacement, 2007 FORD ESCAPE WATER PUMP BELT, 2005 ford escape water pump belt,

1995 Mercury Villager Water Pump Removal Installation

0

Filed Under (Mercury) by admin on 24-02-2011

download
1. Drain the cooling system. Refer to Section 03-03 for the procedure. 2. Disconnect the battery ground cable (14301) . 3. Remove the generator drive belt, water pump and power steering pump drive belt, and the A/C compressor drive belt (if equipped). Refer to Section 03-05 for the removal procedures. 4. Raise and support the vehicle. 5. Use Strap Wrench D85L-6000-A or equivalent to hold the water pump pulley (8509) while removing the four water pump pulley bolts. 6. Remove the water pump pulley from the water pump (8501) . 7. Remove the crankshaft pulley (6312) . Refer to the procedure in this section 8. Remove the five lower engine front cover bolts and the lower engine front cover (6019) . 9. NOTE: Make a note of the location of the one water pump stud/bolt for ease of installation. Remove the six water pump bolts. 10. Remove the water pump . Installation 1. NOTE: Ensure the mating surfaces between the water pump and the cylinder block (6010) are cleaned of any sealant material. Install a continuous 2.0-3.0mm (0.079-0.118 inch) wide bead of Gasket Maker E2AZ-19562-B or equivalent meeting Ford specification WSK-M2G348-A5, on the water pump and position the water pump on the cylinder block . 2. NOTE: Refer to the note made during removal for the location of the stud/bolt. Install the six water pump bolts. Tighten the water pump bolts to 16-21 Nm (12-15 lb-ft). 3. Position the water pump pulley on the water pump and install the four water pump pulley bolts. 4. Use Strap Wrench D85L-6000-A or equivalent to hold the water pump pulley , and tighten the four water pump pulley bolts to 16-21 Nm (12-15 lb-ft). 5. Install the lower engine front cover and the five lower engine front cover bolts. Tighten the five lower engine front cover bolts to 3-5 Nm (27-44 lb-in). 6. Install the crankshaft pulley . Refer to the procedure in this section. 7. Lower the vehicle. 8. Install and adjust the generator drive belt, water pump and power steering pump drive belt, and the A/C compressor drive belt (if equipped). Refer to Section 03-05 for the installation and adjustment procedures. 9. Connect the battery ground cable . 10. Fill the cooling system. Refer to Section 03-03 for the procedure. 11. Start the engine (6007) and check for leaks.

Related entry:

91 chrysler new yorker brake bleed procedure, repair guide 2006 jeep commander power steering pump, strap wrench D85L-6000A,

1998 Ford Mustang Water Pump Removal Installation

0

Filed Under (Ford) by admin on 03-02-2011

download
1. Drain engine cooling system. Refer to Section 03-03. 2. Remove upper radiator sight shield (8C291). 3. Disconnect radiator overflow hose (8075) from radiator (8005). Remove bolts retaining coolant recovery reservoir (8A080) and bracket to radiator support. Disconnect coolant recovery reservoir from lower locator and remove coolant recovery reservoir. 4. Remove cooling fan motor, fan blade (8600) and fan shroud (8146) assembly as described in Section 03-03. 5. Rotate drive belt tensioner (6B209) . Remove drive belt (8620) . Refer to Section 03-05. 6. Remove retaining bolts and water pump pulley (8509) . 7. Remove power steering pump pulley (3A733) and remove water pump-to-power steering pump brace. 8. Remove bolt and nuts retaining ignition coil (12029) and bracket. Position out of the way. 9. Remove heater water outlet tube retaining bolts and heater water outlet tube (18663) from water pump (8501) . 10. Disconnect lower radiator hose (8286) from water pump . 11. CAUTION: If using a prying device to assist in water pump removal, be careful not to damage the mating surfaces. Remove water pump retaining bolts, stud bolts and nuts. Remove water pump . Discard old water pump housing gasket (8507) . Installation 1. NOTE: Lightly oil all bolt and stud threads before installation except those specifying special sealant with SAE 5W-30 Super Premium Motor Oil XO-5W30-QSP or equivalent meeting Ford specification WSS-M2C153-G. Clean gasket surfaces on water pump and engine front cover (6019) . 2. NOTE: Gasket and Trim Adhesive F3AZ-19B508-B or equivalent meeting Ford specifications ESR-M11P17 and ESE-M2G52-A is recommended to hold the water pump housing gasket in position. Position a new water pump housing gasket on water pump sealing surface. 3. NOTE: The threads of the No. 1 water pump retaining bolt must be coated with Pipe Sealant with TeflonĀ® D8AZ-19554-A or equivalent meeting Ford specifications WSK- M2G350-A2 and ESR-M18P7-A before installing. Position water pump on the engine front cover . Install retaining bolts, stud bolts and nuts. Tighten retaining bolts and studs to 20-30 Nm (15-22 lb-ft). Tighten retaining nuts to 8-12 Nm (71-106 lb-in). 4. Inspect O-ring (replace as necessary) and install heater water outlet tube to water pump . Tighten retaining bolts to 8-12 Nm (71-106 lb-in). 5. Position coil and bracket assembly. Tighten retainers to 25 Nm (18 lb-ft). 6. Install lower radiator hose to water pump . Tighten clamps securely. 7. Install water pump-to-power steering pump brace and install water pump pulley .

Related entry:

1996 gmc how to remov waterpo manual pdf, 2003 buick century water pump installation, toyota tacoma water pump torque specs, removing water pump on 2003 hyundai elantra, hydraulic pump circuit malfunction jeep repair cost, toyota echo radiator fan removal, Water Pump Pontiac G6, mazda b2200 water pump removal, Chevy express fan shroud removal, fuel flow npr,

1998 Ford Taurus Fuel Pump Module Removal Installation

0

Filed Under (Ford) by admin on 15-02-2011

download
Removal 1. Remove fuel tank (9002) as described. 2. Remove any dirt that has accumulated around fuel pump module retaining flange. 3. Turn fuel pump module locking retainer ring counterclockwise using Fuel Tank Sender Wrench 310-002 (T74P-9275-A) and remove fuel pump module locking retainer ring. 4. Pull fuel pump module sender plate up out of fuel tank until locking tabs for fuel pump module are accessible. Reach through fuel pump module opening, squeeze both locking tabs together and remove fuel pump module from fuel tank . 5. Remove O-ring seal and discard. Installation 1. Clean fuel pump module retaining flange, fuel tank mounting surface and seal ring groove. 2. Apply a light coating of Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-BA on a new O-ring seal to hold it in place during assembly and install O-ring in seal ring groove. 3. Install fuel pump module carefully into fuel tank to make sure that filter, hoses and float rod are not damaged or binding. Align fuel pump module and fuel tank retainer and push fuel pump module into fuel tank retainer. A definite click will be heard when the two tabs on fuel pump module engage the fuel tank retainer. The fuel pump module must be snapped in the retainer with both tabs. Pull on fuel pump module to make sure it is fully engaged. Install fuel pump module sender plate to fuel tank , being careful that locating keys are in keyways and O-ring seal remains in place. 4. Hold assembly in place and install fuel pump module locking retainer ring finger-tight. Make sure that all locking tabs are under fuel pump module locking retainer ring tabs. 5. Secure fuel pump module unit by rotating fuel pump module locking retainer ring clockwise using Fuel Tank Sender Wrench 310-002 (T74P-9275-A) until fuel pump module locking retainer ring contacts the stops. 6. Install fuel tank in vehicle as described. 7. Lower vehicle. 8. Install a minimum of 38 liters (10 gallons) of fuel. Check for leaks. 9. Turn ignition switch to RUN position for three seconds repeatedly (5 to 10 times) until Multiport Fuel Injection (MFI) Fuel Pressure Gauge 310-012 (T80L-9974-B) or equivalent (depending upon application) shows at least 207 kPa (30 psi). Check for leaks at fittings. 10. Remove Multiport Fuel Injection (MFI) Fuel Pressure Gauge 310-012 (T80L-9974-B) or equivalent (depending upon application), start engine and recheck for leaks.

Related entry:

how to check the fuel pressure in a 95 cadillac deville, 89 G-20 chevy van prime fuel pump after installation, fuel pump on buick lucerne 3800 v6 2008 how do you change, step by step to replace a 2003 kia sedona fuel pump, E60 AIRBAG CONTROL MODULE LOCATION, jetta fuel system schematic diagram, where is the fuel pump fuse in a 2002 malibu?, 1973 corvette fuel pump replacement, changing fuel pump on 01 toyota tundra 4 7, 93 geo prizm 1 8 location of the fuel pump fuse,