2006 kia sportage air conditioning


You are searching repair manual in PDF format about 2006 kia sportage air conditioning use another keyword for search another post or files



  2006 kia sportage air conditioning Direct Download speed 5787 Kb/s

  2006 kia sportage air conditioning Full Version speed 6767 Kb/s




2000 Oldsmobile Intrigue DTC P0410 Secondary Air Injection (AIR) System

0

Filed Under (Oldsmobile) by admin on 10-04-2011

download
Refer to Engine Controls Schematics MAF, Secondary Air Injection Pump Bypass Solenoid, IAC and Secondary AIR Pump . Circuit Description The AIR pump is used on this vehicle to lower tail pipe emissions on start-up. The powertrain control module (PCM) grounds the AIR pump relay control circuit, which energizes the AIR pump. The PCM also grounds the AIR solenoid valve control circuit, which energizes the AIR solenoid valve. The AIR solenoid valve opens allowing manifold vacuum to open the AIR control valves. The PCM enables both control circuits when AIR system operation is desired. When the AIR system is active, the AIR pump forces fresh air into the exhaust stream in order to accelerate catalyst operation. The AIR control valves replace the conventional check valves. When the AIR system is inactive, the AIR control valves prevent air flow in either direction. DTC P0412 applies to the AIR solenoid control circuit. DTC P0418 applies to the AIR pump relay control circuit. DTC P0410 sets if an air flow problem is detected. The PCM will run two tests using the heated oxygen sensor (HO2S) voltage to diagnose the AIR system. Both tests have two parts. The passive test is performed during regular AIR pump operation. The passive test consists of the following: Passive Test Part 1 When the AIR system is enabled, the PCM monitors the HO2S voltage. If the HO2S voltage goes below a threshold, the PCM interprets this as an indication that the AIR system is operational. Passive Test Part 2 When the AIR system is disabled, the PCM monitors the HO2S voltage. The HO2S voltage should increase above a threshold and switch normally. If both of these tests indicate a pass, no further action is taken. If one of the above tests failed or is inconclusive, the diagnostic will proceed to test two. The active test is performed specifically for diagnostic purposes. Test two consists of the following: Active Test Part 1 During this test the PCM turns the AIR system on during closed loop operation. When the AIR system is activated, the PCM monitors the HO2S voltage. If the AIR system is operating properly, the HO2S voltage should go below a predetermined threshold. Active Test Part 2 The PCM turns the AIR system off. The HO2S voltage should return to above a rich threshold.

Related entry:

2006 ford f250 air conditioning problems, hummer h2 ac diagram, recharging a/c unit 1990 ford ranger, recharging air conditioning on 2005 chevy equinox, recharge air conditioner on 2006 toyota corolla, ford 500 air conditioner recharge, 1998 ml320 a/c temp door actuator, kia sedona air conditioning system diagram, where is the air conditioner drain on 2006 sebring, schematic diagrams for air conditioning on a 2006 ford focus,

2002-2005 Subaru Impreza WRX/STI Cold Air Intake Installation Guide

0

Filed Under (Subaru) by admin on 02-01-2011

download
Removal of Factory Intake 1. 2. Turn the ignition OFF and disconnect the vehicle’s negative battery cable. Loosen and remove the two bolts that secure the air inlet duct to the radiator core support, then remove the air inlet duct. Loosen the clamps at the air cleaner assembly and turbo inlet tube, then remove the stock intake tube. Loosen and remove the two bolts that secure the air cleaner assembly. Pull upwards to remove the air cleaner assembly. Using the bolt removed to secure the ABS control bracket. Loosen and remove the two screws that secure the mass air sensor to the air cleaner assembly, then remove the mass air sensor. Raise the vehicle and support with the jack stands, then remove the front passenger side tire. Remove the five plastic push/screw clips that secure the inner wheel house valance. Remove the 6 screw in push clips that secure the air duct to the lower valance, then remove the air duct. Remove the two remaining push clips that secure the lower valance, then pull the valance down. From inside the apron, remove the push clip that secures the apron to the upper fender. Remove the hex nut that secures the air intake resonator to the inner fender. Loosen and remove the second hex nut that secures the air intake resonator from underneath the vehicle. Remove the air intake resonator. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. Install of Intake 16. Install the reducer and clamps onto the turbo and secure. 17. Loosen and remove the hex bolt on the cam cover. 18. Using the provided allen bolts, secure the mass air sensor into the adapter on the intake tube. 19. Using the allen bolts, secure the mass air sensor into the adapter on the intake tube. 20. Slide the intake tube into the reducer and secure the mass air sensor into the adapter on the intake tube. 21. Tighten the clamp on the intake tube. 22. Install the reducer and clamps onto the intake tube. 23. From underneath the vehicle loosen and remove the hex nut that secures the ABS pump to the inner fender. 24. Slide the cold air tube intake tube from underneath the vehicle into the hole in the inner fender, then line up the bracket with the ABS bolts, and tighten with the nut remove. 25. Slide the reducer onto the cold air intake tube. 26. Install the Bomz Filtercharger onto the cold air intake tube and secure with clamp. 27. Reverse the removal process for the plastic wheelhouse valance and air duct with the stock push clips. 28. Reconnect the mass air sensor electrical connection. 29. Reconnect the negative battery cable and double check to make sure everything is tight before starting the vehicle. Resetting the ECU This is to be completed at your own risk. This procedure will reset the computer so that it may “learn” of your new intake. We are not to be held liable for any mishaps that you may occur while completing this process. • • Disconnect the Negative battery cable for 5 minutes. Reconnect the battery cable and false panel cover.

Related entry:

ac drain hose for 2010 mazda sx 9, 1997 gmc jimmy MAF relearn procedure, diagram of where air flow sensor and throttle body is located on a toyota 2006 rav 4, torque pattern 3 8 chrysler upper lower intake, 2001 COUGAR 2 5 LOWER INTAKE SOLENOID, youtube/how to drain saturn a/c unit, p0410 greska ople vektra b, northstar upper plenum, map sensor atpter for cold intake on 2004 subaru forester, intake resonator 2004 deville,

1996 Volkswagen Golf ADJUSTMENTS AIR BAG SPIRAL SPRING REMOVAL & INSTALLATION

0

Filed Under (volkswagen) by admin on 30-06-2011

download
SYSTEM OPERATION CHECK An air bag light is located on left side of instrument cluster. Air bag light is used to indicate readiness of system. Light glows when ignition switch is on or engine is started. Light should stay on about 3 seconds while air bag control unit performs an electronic test of system. If air bag light does not glow when ignition is on or does not go out after 3 seconds, a fault probably exists in system. If a fault occurs while ignition is on, it is stored in fault memory. Warning light will then glow and air bag system will be switched off. If warning light glows or flickers while driving, air bag system should be tested. See DIAGNOSIS & TESTING in appropriate AIR BAG RESTRAINT SYSTEM article in ACCESSORIES/SAFETY EQUIPMENT section. * * ADJUSTMENTS AIR BAG SPIRAL SPRING To center spiral spring assembly, turn spring assembly 3 turns from stop in either direction. REMOVAL & INSTALLATION WARNING: Failure to follow air bag service precautions may result in air bag deployment and personal injury. See SERVICE PRECAUTIONS. After component replacement, perform a system operational check to ensure proper system operation. See SYSTEM OPERATION CHECK. AIR BAG MODULE Removal 1) Before proceeding, follow air bag service precautions. See SERVICE PRECAUTIONS. Disable air bag system. See DISABLING & ACTIVATING AIR BAG SYSTEM. 2) Air bag module is located in steering wheel. See Fig. 1. Remove air bag module Torx head screws from rear of steering wheel. Lift off air bag module from steering wheel, and tilt air bag module downward. Disconnect air bag module connector. AIR BAG RESTRAINT SYSTEM – 1995 AIR BAG RESTRAINT SYSTEM – 1996

Related entry:

2001 buick lesabre air bag sensor and module diagram, dmax air bag indicator, 02 astro van air bag clock spring removal, airbagcontrolmodulelocation1997s10pickup, content, CROWN VICTORIA AIR BAG FUSE LOCATION, disabling airbag warning light on peugeot 806, Front impact sensors for a 2003 S10, how to fix a airbag light on isuzu dmax, how to remove a 1995 chevy astro air bag,

1999 Ford Crown Victoria Air Bag Sliding Contact Removal

0

Filed Under (Ford) by admin on 19-02-2011

download
WARNING: Always wear safety glasses when repairing an air bag supplemental restraint system (SRS) vehicle and when handling an air bag module. This will reduce the risk of injury in the event of an accidental deployment. WARNING: Carry a live air bag module with the air bag and trim cover pointed away from your body. This will reduce the risk of injury in the event of an accidental deployment. WARNING: Do not set a live air bag module down with the trim cover face down. This will reduce the risk of injury in the event of an accidental deployment. WARNING: After deployment, the air bag surface can contain deposits of sodium hydroxide, a product of the gas generant combustion that is irritating to the skin. Wash your hands with soap and water afterwards. WARNING: Never probe the connectors on the air bag module. Doing so can result in air bag deployment, which can result in personal injury. WARNING: Air bag modules with discolored or damaged trim covers must be installed new, not repainted. WARNING: Vehicle sensor orientation is critical for correct system operation. If a vehicle equipped with an air bag supplemental restraint system (SRS) is involved in a collision, inspect the sensor mounting bracket and wiring pigtail for deformation. Replace and properly position the sensor or any other damaged supplemental restraint system (SRS) components whether or not the air bag is deployed. WARNING: To avoid accidental deployment and possible personal injury, the backup power supply must be depleted before repairing or replacing any front or side air bag supplemental restraint system (SRS) components and before servicing, replacing, adjusting or striking components near the front or side air bag sensors, such as doors, instrument panel, console, door latches, strikers, seats and hood latches. Please refer to the appropriate vehicle shop manual to determine location of the front air bag sensors. The side air bag sensors are located at or near the base of the B-pillar. To deplete the backup power supply energy, disconnect the battery ground cable and wait at least one minute. Be sure to disconnect auxiliary batteries and power supplies (if equipped). NOTE: Repair is made by installing a new part only. If the new part does not correct the condition, install the original part and perform the diagnostic procedure again. 1. Disconnect the battery ground cable (14301) and wait at least one minute. For additional information, refer to Section 414-01. 2. Remove the driver air bag module. For additional information, refer to Module — Driver Air Bag in this section. 3. NOTE: Make sure the wheels (1007) are in the straight-ahead position. Remove the steering wheel (3600). For additional information, refer to Section 211-04. 4. Apply two strips of masking tape across the air bag sliding contact (14A664) to prevent accidental rotation when the air bag sliding contact is removed. 5. Place the steering column in the full down tilt position, then remove the tilt wheel handle and shank (3F609). 6. Remove the lower steering column cover. 1. Remove the two bolts. 2. Position the parking brake release aside. 3. Remove the lower steering column cover.

2007 Pontiac Grand Prix Secondary Air Injection Pump Replacement Removal Procedure

0

Filed Under (Pontiac) by admin on 17-10-2010

download
1. Remove the air cleaner assembly. 2. Disconnect the engine wiring harness electrical connector from the secondary air injection (AIR) pump electrical connector. 3. Squeeze the tangs together on the AIR pump inlet hose clamp at the pump until they lock, and reposition the clamp. 4. Remove the AIR pump inlet hose from the AIR pump. 5. Squeeze the tangs together on the AIR pump outlet hose clamp (3) at the pump until they lock, and reposition the clamp. 6. Raise and suitably support the vehicle. Refer to Vehicle Lifting. 5. Squeeze the tangs together on the AIR pump outlet hose clamp (3) at the pump until they lock, and reposition the clamp. 6. Raise and suitably support the vehicle. Refer to Vehicle Lifting. 1. Install the AIR pump. 2. Raise and suitably support the vehicle. Notice: Refer to Fastener Notice in Service Precautions. 3. Install the AIR pump nuts (2). Tighten the nuts to 9 N.m (80 lb in). 4. Install the AIR pump electrical connector clip (1) to the bracket. 5. Lower the vehicle. Install the AIR pump outlet hose to the AIR pump. 7. Position and release the AIR pump outlet hose clamp. 8. Install the AIR pump inlet hose to the AIR pump. 9. Position and release the AIR pump inlet hose clamp. Connect the engine wiring harness electrical connector to the AIR pump electrical connector. 11. Install the air cleaner assembly.

Related entry:

08 cobalt air pump, location of air pump on 2000 park ave, how do u replace a air pump on 2003 530 bmw, checking cobalt 2008 air pump, AIR PUMP RELAY 2000 PONTIAC, 2007 grand prix high voltage relay for secondary injection, sendary air flow 2000 s10 located, REPAIR COST ON GRAND PRIX SECONDARY AIRPUMP, 1994 chevy silverado air pump, 2000 buick park avenue air suspension pump,