2006 chevrolet silverado 1500 2WD
You are searching repair manual in PDF format about 2006 chevrolet silverado 1500 2WD use another keyword for search another post or files
2006 chevrolet silverado 1500 2WD Direct Download speed 5787 Kb/s
2006 chevrolet silverado 1500 2WD Full Version speed 6767 Kb/s
Filed Under (Chevrolet) by admin on 20-01-2011
Vehicle Application: Customer Concern: Tests/Procedures: Potential Causes: Diagnostic Codes: 2002 GAS, 2003 GAS, Chevrolet Silverado 1500 4.8L, Vin V, Eng Cfg V8, USA/Canada Chevrolet Silverado 1500 4.8L, Vin V, Eng Cfg V8 The engine runs, but lacks power when driving. Has codes P0101 and P0300. Scanner shows misfires all on the same side of the engine. 1. Check the catalytic converter, on the “suspect” bank of the engine, for a restricted (plugged) exhaust system to that side of the engine. 2. Disconnect both front O2 sensors, re-set the fuel trims and see if the problem goes away. 3. If gone with the O2 sensors disconnected, then swap the sensors side to side and see if the problem follows the O2 sensor. Plugged Exhaust System Oxygen Sensor P0101, P0300 2003 Chevrolet Tahoe 4.8L, GAS, Vin V 2003 Chevrolet Tahoe 5.3L, FLEX, Vin Z
The following diagnostics might be helpful if the vehicle exhibits the conditlon(s) described above. Use the appropriate recommendation based on what symptom has occurred. Recommendation/Instructions No DTCs Review Corporate Bulletin Number 05-02-32-002B to assure you do not have a blown 60 amp steering fuse. The fuse can be blown during improper jump starting of the vehicle on the HHR and ION. Check for this particularly for tow in conditions. DO NOT replace the steering column unless an internal short has been Identified in the column that is causing fuse to blow. Power Steering Warning Message on DIC with DTCs C0176 and C0476 This condition is often the result of excessive lock-to-lock turns of the steering wheel, causing the thermal protection in the Power Steering Control Module (PSCM) to take the steering motor temporarily off line. This is a normal operating characteristic of the system. DO NOT replace the steering column for this condition. Refer to Corporate Bulletin Number 06-02-32-002B for additional information
Filed Under (Chevrolet) by admin on 11-01-2011
Models: 1982-2005 GM Passenger Cars and Light Duty Trucks 2006-2007 Buick Rainier 2006 Cadillac Escalade, Escalade ESV, Escalade EXT 2006 Chevrolet SSR 2006-2008 Chevrolet Avalanche, Colorado, Express, Silverado Classic, Silverado, Suburban, Tahoe, TrailBlazer 2006 GMC Yukon Denali, Yukon Denali XL 2006-2008 GMC Canyon, Envoy, Savana, Sierra Classic, Sierra, Yukon, Yukon XL 2006 Pontiac GTO 2006-2007 HUMMER H2 2006-2008 HUMMER H3 2006-2008 Saab 9-7X with 4L60, 4L60E, 4L65E or 4L70E Automatic Transmission (RPOs MD8, M30, M32, M33 or M70) Condition Some customers may comment that the vehicle has no movement when the transmission is shifted to DRIVE or THIRD position, but there is normal operation when it is shifted to SECOND, FIRST or REVERSE position. Cause This condition may be caused by a damaged forward sprag assembly (642). Correction When inspecting the sprag, it is important to test the sprag for proper operation by holding the outer race (644) with one hand while rotating the input sun gear (640) with the other hand. The sun gear should rotate only in the counterclockwise direction with the input sun gear facing upward. If the sprag rotates in both directions or will not rotate in either direction, the sprag elements should be inspected by removing one of the sprag reserved. retaining rings (643). Refer assembly © 2010 General Motors. All rights
Filed Under (GM) by admin on 20-05-2010
2001-2002 Chevrolet Camaro 2001-2003 Chevrolet Corvette 2001-2002 Pontiac Firebird 2002-2003 Cadillac Escalade, Escalade EXT
2000-2003 Chevrolet Suburban, Tahoe 2001-2003 Chevrolet Silverado 2002-2003 Chevrolet Avalanche 2000-2003 GMC Yukon, Yukon XL 2001-2003 GMC Sierra with 4.8L, 5.3L, 5.7L or 6.0L V8 Engine (VINs V, T, Z, G, S, N, U – RPOs LR4, LM7, L59, LS1, LS6, LQ9, LQ4)
Condition Some customers may comment on an engine tick noise. The distinguishing characteristic of this condition is that it likely will have been present since new, and is typically noticed within the first 161-322 km (100-200 mi). The noise may often be diagnosed as a collapsed lifter. Additionally, the noise may be present at cold start and appear to diminish and then return as the engine warms to operating temperature. This noise is different from other noises that may begin to occur at 3219-4828 km (2000-3000 mi).
Filed Under (Chevrolet) by admin on 05-08-2010
1. If equipped, remove the IP sound insulator. 2. Disconnect the electrical connection from the blower motor. 3. Disconnect the electrical connection from the blower motor resistor. Remove the blower motor resistor retaining screws. 5. Remove the blower motor resistor. INSTALLATION PROCEDURE 1. Install the blower motor resistor. NOTE: Refer to Fastener Notice in Service Precautions. 2. Install the blower motor resistor retaining screws. Tighten Tighten the screws to 1.6 N.m (14 lb in) . 3. Connect the electrical connection to the blower motor resistor. 4. Connect the electrical connection to the blower motor. 5. If equipped, install the IP sound insulator.