2006 chevy silverado 6lt firing order
You are searching repair manual in PDF format about 2006 chevy silverado 6lt firing order use another keyword for search another post or files
2006 chevy silverado 6lt firing order Direct Download speed 5787 Kb/s
2006 chevy silverado 6lt firing order Full Version speed 6767 Kb/s
Filed Under (Buick) by admin on 18-01-2011
Engine Electrical > Firing Orders Firing Orders To avoid confusion, always replace spark plugs and wires one at a time. Replacing spark plugs and wires one at a time will help prevent incorrect wire routing or cross-firing resulting from an incorrect firing order. If more than one wire is to be disconnected at a single time, be sure to tag all of the cables to assure proper installation. Also, be disconnecting the cables, compare the firing order and routing to these diagrams and note any differences for installation purposes. This will help assure the wires are properly installed.
Filed Under (Chevrolet) by admin on 11-01-2011
Models: 1982-2005 GM Passenger Cars and Light Duty Trucks 2006-2007 Buick Rainier 2006 Cadillac Escalade, Escalade ESV, Escalade EXT 2006 Chevrolet SSR 2006-2008 Chevrolet Avalanche, Colorado, Express, Silverado Classic, Silverado, Suburban, Tahoe, TrailBlazer 2006 GMC Yukon Denali, Yukon Denali XL 2006-2008 GMC Canyon, Envoy, Savana, Sierra Classic, Sierra, Yukon, Yukon XL 2006 Pontiac GTO 2006-2007 HUMMER H2 2006-2008 HUMMER H3 2006-2008 Saab 9-7X with 4L60, 4L60E, 4L65E or 4L70E Automatic Transmission (RPOs MD8, M30, M32, M33 or M70) Condition Some customers may comment that the vehicle has no movement when the transmission is shifted to DRIVE or THIRD position, but there is normal operation when it is shifted to SECOND, FIRST or REVERSE position. Cause This condition may be caused by a damaged forward sprag assembly (642). Correction When inspecting the sprag, it is important to test the sprag for proper operation by holding the outer race (644) with one hand while rotating the input sun gear (640) with the other hand. The sun gear should rotate only in the counterclockwise direction with the input sun gear facing upward. If the sprag rotates in both directions or will not rotate in either direction, the sprag elements should be inspected by removing one of the sprag reserved. retaining rings (643). Refer assembly © 2010 General Motors. All rights
Filed Under (Ford) by admin on 23-04-2010
Torque Specs always torque bolts in three equal increments Lube or Sealer Torque to: Engine Oil 105 ft-lbs. Connecting Rod Bolts Engine Oil 45 ft-lbs. Engine oil 140 ft-lbs. (blind hole) (water jacket) Rocker Arms (non-adjustable) Engine Oil 20 ft-lbs. Engine Oil 25 ft-lbs. Engine Oil 15 ft-lbs. Cam Bolt (upper gear) Thread Locker 45 ft-lbs. Engine Oil 20 ft-lbs. Non- Hardening 30 ft-lbs. Sealer Engine Oil 10 ft-lbs. Flexplate (Automatic) Thread Locker 85 ft-lbs.
Filed Under (Ford) by admin on 04-10-2010
Engine miss, spark knock, buck/jerk, surge and other driveability concerns may be caused by induction crossfire. This occurs because of improperly routed spark plug wires. ACTION: If spark plug replacement is performed, the correct firing order and spark plug wire routing is essential to prevent the possibility of induction crossfire between cylinders. Refer to the following procedures for inspection of the spark plug wire routing and firing order. Properly reroute the spark plug wires if required. FIRING ORDER ^ The firing order for 1987-1993 vehicles is 1-5-4-2-6-3-7-8. If # 7 and # 8, or # 2 and # 4 spark plug wires are routed next to each other at the separation bracket, an induction crossfire condition can occur. ^ The firing order for 1994 vehicles is 1-3-7-2-6-5-4-8. On these vehicles the # 1 and # 3, or # 5 and # 6 spark plug wires must be separated to eliminate the possibility of an induction crossfire. ^ To eliminate the possibility of the coil wire becoming disconnected, route the coil wire under the spark plug wires at the distributor cap. 1987-1993 VEHICLES
Filed Under (Mazda) by admin on 18-04-2010
ome vehicles equipped with a 3.0L engine may exhibit a ticking noise from the left bank cylinder head while the engine is running at normal operating temperature. Customers having this concern should have their vehicle repaired using the following repair procedure. Use the table below to select the correct repair for the applicable model
A. REPAIR PROCEDURE 2002 – 2006 MPV 3.0L: 2001 – 2006 TRIBUTE 3.0L – (built BEFORE Jan. 17, 2006): CAUTION: Before attempting a 2001-2006 Tribute repair, confirm if water pump pulley is driven by INTAKE or EXHAUST camshaft. Be sure to use correct repair procedure. The water pump on 2001-2006 Tribute vehicles built BEFORE Jan. 17, 2006 are driven by the “INTAKE” camshaft pulley. 1. Verify the water pump is driven by the INTAKE camshaft pulley. 1572g WATER PUMP DRIVEN BY INTAKE CAMSHAFT PULLEY