2007 jeep compass alternator removal


You are searching repair manual in PDF format about 2007 jeep compass alternator removal use another keyword for search another post or files




06-07 DODGE CALIBER/JEEP COMPASS, PATRIOT; 07-08 WRANGLER CRUISE CONTROL SWITCH

0

Filed Under (Jeep) by admin on 22-04-2010

download

REMOVE THE NEGATIVE BATTERY CABLE BEFORE INSTALLING THE CRUISE CONTROL COMPONENTS FOR SAFETY PRECAUTIONS.
FIGURE 1. 2. JEEP WRANGLER APPLICATIONS: REMOVE AIRBAG BY USING ( TRIM TOOL TO RELEASE METAL CLIPS AS SHOWN IN FIGURE 2. CAUTION: ENSURE THAT BATTERY HAS BEEN 90 SECONDS DISCONNECTED FOR MORE THAN PRIOR TO REMOVAL OF AIRBAG; FAILURE TO HEED THIS WARNING MAY RESULT IN AIRBAG DISCHARGE AND MAY CAUSE SERIOUS INJURY OR DEATH. 3. DODGE CALIBER, JEEP COMPASS/PATRIOT APPLICATIONS: REMOVE AIRBAG BY EXTRACTING THE (2) 10MM SCREWS AS ILLUSTRATED IN FIGURE 2A. 4. PRESS IN SIDES OF BOTH CONNECTORS TO REMOVE AIRBAG FIGURE 3. AS ILLUSTRATED IN CAUTION: BE AIRBAG SURE TO STORE FACE UP AS FIGURE 3A ILLUSTRATED IN TO REDUCE INJURY IN EVENT OF ACCIDENTAL DISCHARGE OF AIRBAG.
5. JEEP WRANGLER REMOVE 13MM BOLT TO TAKE OFF STEERING WHEEL, THEN SKIP ON PAGE 6. DODGE CALIBER, JEEP COMPASS/PATRIOT APPLICATIONS: REMOVE (3) TORX 25 SCREWS TO RELEASE CENTER BRACKET INSIDE STEERING WHEEL. FIGURE 4

CHRYSLER ALTERNATOR REMOVAL & INSTALLATION

0

Filed Under (Chrysler) by admin on 28-12-2010

download
CHRYSLER ALTERNATOR See Figures 1, 2, 3, 4 and 5 Fig. 1: Alternator mounting-2.2L and 2.5L engines Fig. 2: Disconnecting alternator wiring-2.2L and 2.5L engines Fig. 3: Disconnecting alternator wiring Fig. 4: Removing the pivot bolt and nut Fig. 5: Removing the alternator from the vehicle Disconnect the negative battery cable. Label and disconnect the wiring (for easy installation). Remove the air conditioning compressor drive belt, if equipped. Loosen the alternator adjusting bracket bolt and adjusting bolt. Remove the alternator belt. 5. Remove the bracket and mounting bolts. 6. Remove the pivot bolt and nut. 7. Lift the alternator from the vehicle. When lifting the alternator out of the vehicle on some years with A/C, clearance may be restricted by the condenser cooling fan assembly or the A/C compressor and mounting bracket assembly, if so, removal of one of these items will be necessary. 8. Position the alternator against the engine. 9. Install the pivot bolt and nut. 10. Install the mounting bracket bolts, and adjusting bolt. 11. Install drive belts and adjust to specification. 12. Tighten all the mounting bolts and nuts. 13. Connect all alternator terminals. 14. Connect the negative battery cable. Disconnect the negative battery cable. Disconnect the wiring and label for easy installation. Remove the air conditioning compressor drive belt. Loosen the alternator adjusting bracket locknut and adjusting screw. Remove the alternator belt. 5. Remove the bracket locknut and mounting bolt. 6. Remove the pivot bolt and nut. 7. Remove the alternator from the engine. 8. Position the alternator against the engine. 9. Install pivot bolt and nut. 10. Set the mounting bracket in place and install the bracket mounting bolt and locknut. 11. Install the drive belts and adjust to specification. 12. Tighten all the mounting bolts and nuts. 13. Connect all alternator terminals. 14. Connect the negative battery cable.

VARIABLE VALVE TIMING (VVT) NOISE WHEN STARTING ENGINE 2007 Mazdaspeed 3 2006-2007 Mazdaspeed 6 2007 Mazda CX-7

0

Filed Under (Mazda) by admin on 20-10-2009

APPLICABLE MODEL(S)/VINS
2007 Mazdaspeed3 vehicles with VINs lower than JM1BK******742222 (produced before April 1, 2007)
2006-2007 Mazdaspeed6 vehicles with VINs lower than JM1 GG******109660 (produced before April 1, 2007)
2007 Mazda CX-7 vehicles with VINs lower than JM3ER******166945 (produced before April 1, 2007)
DESCRIPTION
When the engine is first started, some vehicles may exhibit a loud ticking noise from the variable valve timing
(VVT). This is caused by the lock pin of the variable valve timing actuator not fully engaging. Heat treatment has
now been added around the hole of the variable valve timing rotor lock pin to prevent this from happening

download

2007 Chevrolet Impala 4T65E Transmission 1-2 Shift Shudder at Light to Moderate Acceleration (Replace Complete Second Clutch Assembly)

0

Filed Under (Chevrolet) by admin on 21-10-2010

download
Models: 2001-2004 Buick Regal 2001-2005 Buick Century, LeSabre 2002-2007 Buick Rendezvous 2005-2007 Buick Terraza, LaCrosse, Allure (Canada Only) 2006-2007 Buick Lucerne 2001-2005 Chevrolet Venture 2001-2007 Chevrolet Impala, Monte Carlo 2005-2007 Chevrolet Uplander 2006-2007 Chevrolet Malibu SS, Malibu Maxx SS 2001-2002 Oldsmobile Intrigue 2001-2003 Oldsmobile Aurora 2001-2004 Oldsmobile Silhouette 2001-2005 Pontiac Aztek, Bonneville, Montana 2001-2007 Pontiac Grand Prix 2005-2007 Pontiac Montana SV6 2006-2007 Pontiac G6 GTP 2005-2007 Saturn Relay with 4T65E Automatic Transmission (RPOs MN3, MN7, M15, M76) Condition Some customers may comment on a 1-2 shift shudder at light to moderate acceleration. Typically, the throttle plate angle parameter is 12-20% at time of condition with vehicle speed of approximately 24-40 km/h (15-25 mph). The customer may describe the condition as slip or delayed shift into second. Correction Replace the complete second clutch assembly with service kit, P/N 24240561. Refer to the GM Unit Repair Service Manual for the year and model of the vehicle being serviced for the 2nd Clutch service procedure. This service kit contains: Second Clutch Housing Fluid Seal Rings (613), a Second Clutch Assembly (617), a Case Cover (Channel Plate) Upper Gasket (430), and a Case Cover (Channel Plate) Lower Gasket (429). In addition to the content of this service kit, other gaskets not included in this service kit will also be needed to complete the repair – a Case Cover Lower Gasket (429), and a Case Cover Upper Gasket (430). These gaskets can be obtained by ordering gasket kit 24206391. Be sure to use ONLY the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings provided in this service kit. DISCARD the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings removed from the transmission being serviced. Disassemble ONLY the Oil Pump Assembly from the Case Cover (Complete). DO NOT disassemble the Control Valve Body from the Case Cover. Remove ONLY the Case Cover-to-Case bolts to remove the Case Cover and Valve Body from Transmission Case AS AN ASSEMBLY . To access all Case Cover-to-Case bolts, it is necessary to remove the Pressure Control Solenoid Valve Assembly (322), and 1-2 & 3-4 Shift Solenoid Valve

Renault CLIO II with AC: XBXX – K9K – K4J – K4M engines Alternator pulley replacement

0

Filed Under (Renault) by admin on 10-06-2011

download
Special tooling required Mot. 1732 Tool for removing and re?tting the alternator pulley Tightening torquesm the alternator decou- pling pulley I – PARTS AND CONSUMABLES FOR THE REPAIRS Parts always to be replaced: – the alternator belt, – the tensioning roller, – the mechanic tension wheel mounting bolts. II – PRECAUTIONS DURING REPAIR It is essential to replace an alternator decoupling pulley with a decoupling pulley. III – EQUIPMENT REQUIRED – Torque wrench capable of tightening a left-hand thread. IV – REMOVAL Remove the vehicle alternator (see 16A, Starting – charging, Alternator 110276 110268 Position adapter (2) from the tool kit (Mot. 1732) (corresponding to the alternator rotor recess) in the hexagon socket (1). 110267 Position the hexagon socket (1) from the tool box (Mot. 1732) in the alternator pulley. 110269 Position the adapter holder (3) in socket (2). 110270 Hold the hexagon socket (1) using an open-jawed spanner (4). Loosen the decoupling pulley (5) using a ratchet, (6) (turning it in the clockwise direction.). Remove the decoupling pulley. V – REFITTING Position: – the hexagon socket in the alternator (1), – the adapter (2) (corresponding to the alternator ro- tor mark), – the adapter holder (3) on the adapter(2). Note: Check that the torque wrench is capable of tigh- tening in an anticlockwise direction. 110266 Screw the new decoupling pulley onto the alternator rotor. Tighten to torque the alternator decoupling pulley (80 Nm) using a torque wrench(7). Refit the vehicle alternator (see 16A, Starting – charging, Alternator).