Auto Repair Manual Free Download and ReviewsFree download ebook pdf files automotive manual

download
Some 2006-2007 Freestar and Monterey vehicles may experience a melted or damaged spark plug electrode, malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC’s) P030X, rough idle, engine knock/ping on acceleration. Pre-ignition (which yields these symptoms) may be caused by water entering the powertrain control module (PCM). ACTION: Follow the Service Procedure steps to correct the condition. SERVICE PROCEDURE 1. Remove PCM from vehicle. Refer to Workshop Manual (WSM), Section 303-14. 2. Remove the PCM cover by carefully bending back the four (4) retaining clips holding the galvanized metal cover to the top plate. (Figure 1) Figure 1 – Article 07-14-1 3. Look for evidence of water within the PCM (liquid water, rust, water stains or deposits). (Figure 2) If found – obtain a replacement PCM before continuing on to Step 4. If no water is found, continue on to step 4 with the vehicle’s original PCM. Figure 2 – Article 07-14-1 4. Set the PCM top plate in a clean, dry location where the circuitry will be protected from damage. 5. With the PCM cover removed, drill a 1/4″ hole on each of the four (4) corners of the PCM cover. Get as close to the corner as possible. (Figure 3) Figure 3 – Article 07-14-1 6. De-burr the edges on both inside and outside surfaces. (Figure 3) Be sure to vacuum off all chips and wipe off all metal dust and any machining oil. 7. Clean the surfaces of the PCM cover with Motorcraft ZC-21 (Metal Surface Cleaner) or equivalent. Also clean the edges of the PCM top plate. The metal surfaces must be completely clean before proceeding to Step 8. 8. Apply Motorcraft TA-29 Ultra Silicone Sealant to all edges depicted. (Figure 4, 5, 6, 7) Proceed directly to Step 9 – do not let the sealant skin over. NOTE: Motorcraft TA-32 can NOT be used since its constituents may damage the PCM circuitry.

download
FORD: 2005-2008 Mustang 2004-2008 F-150 2005 Excursion 2005-2008 Expedition, F-Super Duty 2006-2008 Explorer, F-53 Motorhome Chassis 2007-2008 Explorer Sport Trac This article supersedes TSB 08-1-9 to update Vehicle Applications, Service Procedure and Part List. ISSUE Some 2004-2008 F-150, 2006-2008 Mark LT, 2005-2008 F-Super Duty, Expedition, Navigator and 2005 Excursion, with 5.4L 3-V engine; 2005-2008 Mustang, 2006-2008 Explorer, Mountaineer, and 2007-2008 Explorer Sport Trac with 4.6L 3-V engine; 2005-2008 F-Super Duty, 2006-2008 F-Stripped Chassis, and 2005 Excursion, with 6.8L 3-V engine may experience difficulty with spark plug removal. This may cause damage to the spark plug and leave part of the spark plug in the cylinder head. Affected engine build dates are as follows: 5.4L 3-V and 6.8L 3-V before 10/9/07, 4.6L 3-V before 11/30/07. ACTION Refer to the following Service Procedure for techniques to remove the spark plugs and extract broken spark plugs. SERVICE PROCEDURE The engine build date can be read on the left hand cam cover information sticker. To remove spark plugs without damage, it is necessary to adhere exactly to this procedure before removal is attempted. LINCOLN: 2005-2008 Navigator 2006-2008 Mark LT MERCURY: 2006-2008 Mountaineer

download
GM Accessories Headrest DVD System Display Monitor Inoperative (Install Cable Connector Clamps) 2004-2007 Buick Rainier 2008 Buick Enclave 2003-2008 Cadillac Escalade Models 2005-2008 Cadillac CTS, SRX, STS 2006-2008 Cadillac DTS 2003-2008 Chevrolet Avalanche, Silverado, Suburban, Tahoe, TrailBlazer Models 2006-2008 Chevrolet Colorado 2007-2008 Chevrolet Equinox, HHR 2003-2008 GMC Envoy Models, Sierra, Yukon Models 2006-2008 GMC Canyon 2007-2008 GMC Acadia 2007-2008 Pontiac Torrent 2005-2008 HUMMER H2 2006-2008 HUMMER H3 2007-2008 Saturn OUTLOOK 2005-2008 Saab 9-7X Condition Some customers may comment on an inoperative display monitor or monitors in the GM Accessories Headrest DVD System. Cause This condition may be caused by a loose connection at the display monitor cable connectors. These connectors are located at the lower rear part of both front seats. Two cables are routed to the display monitor in each seat.

download
ISSUE Some 2004-2008 F-150, 2006-2008 Mark LT, 2005-2008 F-Super Duty, Expedition, and Navigator, with 5.4L 3-V engine; 2005-2008 Mustang, 2006-2008 Explorer, Mountaineer, and 2007-2008 Explorer Sport Trac with 4.6L 3-V engine; 2005-2008 F-Super Duty, 2006-2008 and F-Stripped Chassis, with 6.8L 3-V engine may experience difficulty with spark plug removal. This may cause damage to the spark plug and leave part of the spark plug in the cylinder head. Affected engine build dates are as follows: 5.4L 3-V and 6.8L 3-V before 10/9/07, 4.6L 3-V before 11/30/07. ACTION Refer to the following Service Procedure for techniques to remove the spark plugs and extract broken spark plugs. SERVICE PROCEDURE The engine build date can be read on the left hand cam cover information sticker. To remove spark plugs without damage, it is necessary to adhere exactly to this procedure before removal is attempted. CAUTION DO NOT REMOVE PLUGS WHEN THE ENGINE IS WARM OR HOT. THE ENGINE MUST BE AT ROOM TEMPERATURE WHEN PERFORMING SPARK PLUG SERVICE. REMOVING THE SPARK PLUGS FROM A WARM/HOT ENGINE INCREASES THE CHANCE THE THREADS COULD BE DAMAGED. Spark Plug Removal Procedure 1. Remove the coil-on-plug assemblies and thoroughly blow out the spark plug wells and surrounding valve cover area with compressed air. 2. Back out the spark plugs no more than 1/8 to 1/4 of a turn. Using Motorcraft(R) Carburetor Tune-Up Cleaner, fill the spark plug well just above where the jamb nut hex sits (1/2 – 3/4 teaspoon). A minimum period of 15 minutes of soak time is required. The cleaner will wick down to the ground electrode shield and soften the carbon deposits in this time. DO NOT WORK the spark plug back and forth at this point. NOTE COMPLETELY REVIEW THE PRODUCT LABEL FOR THE MOTORCRAFT CARBURETOR TUNE-UP CLEANER PRODUCT – USE AT ROOM TEMPERATURE AND SHAKE WELL.

download
REMOVAL CAUTION: All spark plugs installed on an engine, must be of the same heat range. Spark plug CHAMPION: RC10YC4 NGK: BKR5E-11 (Alternate) NGK: BKR6E-11 (Alternate) RH SIDE 1. Disconnect the ground cable from battery. 2. Remove the resonator chamber. 3. Remove the spark plug cords by pulling boot, not the cord itself. 4. Remove the spark plugs with spark plug sockets. LH SIDE 1. Disconnect the around cable from battery. 2. Remove the two bolts which hold washer tank, and then disconnect the washer motor connector. 3. Disconnect the rear window glass washer hose from washer motor, then plug connection with a suitable cap. 4. Hang the washer tank away from working area. 5. Remove the spark plugs cord by pulling boot, not the cord itself. 6. Remove the spark plugs with spark plug sockets. INSTALLATION RH SIDE 1. Install in the reverse order of removal. Tightening torque (Spark plug): 21 No.m (2.1 kegs.m, 15.2 ft.lb) CAUTION: The above torque should be only applied to new spark plugs without oil on their threads. In case their threads are lubricated, the torque should be reduced by approx. 1/3 of the specified torque in order to avoid over-stressing. LH SIDE 1. Install in the reverse order of removal. Tightening torque (Spark plug): 21 No.m (2.1 kegs.m, 15.2 ft.lb) CAUTION: The above torque should be only applied to new spark plugs without oil on their threads. In case their threads are lubricated, the torque should be reduced by approx. 1/3 of the specified torque in order to avoid over-stressing.