2008 dodge avenger power window diagram


You are searching repair manual in PDF format about 2008 dodge avenger power window diagram use another keyword for search another post or files



  2008 dodge avenger power window diagram Direct Download speed 5787 Kb/s

  2008 dodge avenger power window diagram Full Version speed 6767 Kb/s




1996 Lincoln Town Car Power Window Regulator REMOVAL AND INSTALLATION

0

Filed Under (Lincoln) by admin on 31-03-2011

download
Window Regulator, Power Front Door—Town Car Removal 1. CAUTION: When servicing front door power window regulator minus motor (23208), regulator cable tension must not be altered. Cable tension is preset at production. Improper adjustment may result in premature front door power window regulator failure or erratic operation. CAUTION: Be careful not to drill through the window regulator behind inner door panel. Additional repairs may be necessary. If front door window glass (21410) is in the down position and is inoperable, a through f must be taken; if front door window glass is operational, proceed to Step 2. a. Remove front door trim panel (23942) and front door trim shield (237A04). Refer to Section 01-05. b. Disconnect battery ground cable (14301). Refer to Section 14-01. c. CAUTION: Be careful not to strike or scratch front door window glass. Remove three 1/4 inch rivets retaining window regulator electric drive (23394) to inner panel. d. Working through front access hole in inner panel, remove three screws from window regulator electric drive. e. Separate window regulator electric drive from front door power window regulator minus motor. Raise front door window glass by hand and secure using tape. f. Proceed to Step 2. 2. Remove front door window glass as outlined. 3. Disconnect window regulator electric drive wiring connector. 4. Remove two upper front door power window regulator retaining nuts. 5. NOTE: Use care not to enlarge sheet metal holes in the door inner panel. Remove two 1/4-inch rivets retaining front door power window regulator minus motor to inner door panel. 6. Remove front door power window regulator minus motor from front door (20124). Installation 1. Lubricate front door power window regulator minus motor with Teflon® Lubricant E7FZ-19590-A or equivalent meeting Ford specification ESB-M1C111-A as outlined. 2. Install front door power window regulator minus motor into access hole in inner panel. 3. Position front door power window regulator minus motor using upper front door power window regulator studs and tabs on window regulator electric drive mounting bracket. 4. Install rivets retaining front door power window regulator minus motor to door inner panel (1/4-20 x 1/2 inch screw and 1/4-20 nut and washer assemblies or equivalent metric fasteners may be used as alternates). 5. Install two upper front door power window regulator retaining nuts. 6. Install Front Door Window Glass as outlined. 7. Adjust Front Door Window Glass as outlined. 8. Install front door trim shield and front door trim panel. Refer to Section 01-05. Front Door—Crown Victoria, Grand Marquis Removal 1. If front door window glass is in the down position and is inoperable, the following steps must be taken; if front door window glass is operational, go to Step 2. a. Remove front door trim panel and front door trim shield. Refer to Section 01-05. b. Disconnect battery ground cable. Refer to Section 14-01. c. Disconnect window regulator electric drive wires. d. CAUTION: Be careful not to strike or scratch front door window glass because it could break. Remove window regulator electric drive retaining screws through holes. e. Remove window regulator electric drive from front door power window regulator minus motor.

Related entry:

removing Kia sendoa window regulator, how to remove actuator motor saturn ion, 2008 Dodge Avenger Window Diagram, 1985 k10 window wiring schematic, 2008 dodge avenger window regulator diagram, 2005 kia sorento window inoperative, WINDOW REGULATOR PROBLEMS ON A 2005 LEXUS ES330, verada window cable diagram, 2008 chevy equinox driver side wiring, 2008 suzuki xl7 doors lock and wont unlock,

2002 Chrysler Voyager LX Power Windows TROUBLE SHOOTING

0

Filed Under (Chrysler) by admin on 09-12-2010

download
Inspect power window circuit breaker (25-amp), located in left kick panel. Inspect fuse No. 28 (40-amp) in Intelligent Power Module (IPM). IPM is located on left side of engine compartment. Inspect ground at right “B” pillar. SYSTEM TESTS ALL WINDOWS INOPERATIVE 1. Check power window system circuit breaker and fuse. See TROUBLE SHOOTING . Replace components as necessary. If components are okay, go to next step. 2. Remove driver’s power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. Turn ignition on. Using test light, connect ground lead to harness connector terminal No. 13 (Black/Brown wire). Check for voltage by touching test light probe to harness connector terminals No. 9, 11 and 14 (all White/Pink wires). 3. If test light does not illuminate, check power and ground circuits. See WIRING DIAGRAMS . If test light illuminates, ground circuit and power circuit between battery and switch are okay. Check switch and motor. See POWER WINDOW SWITCH and POWER WINDOW MOTOR under COMPONENT TESTS. COMPONENT TESTS VENT WINDOW MOTOR 1. Remove “D” pillar trim panel. See “D” PILLAR TRIM PANEL under REMOVAL & INSTALLATION. 2. Disconnect power vent window motor wire connector from body harness. 3. Using 2 jumper wires, connect one to a battery (+) source and the other to a good ground (-). 4. Connect the negative (-) jumper probe to one of the motor connector terminals. 5. Momentarily touch the positive (+) jumper probe to the other motor connector terminal. When the positive probe is connected, the motor should rotate in one direction to either move window open of closed. If window is all the way open or closed the motor will grunt and the crank system will flex when actuated in the one direction. Reverse jumper probes at the motor connector terminals and window should now move in the opposite position to verify full operation. If motor grunts and does not move with the motor connected in both directions, verify that crank system is not binding. POWER WINDOW MOTOR 1. Remove door trim panel and sound pad. See DOOR TRIM PANEL under REMOVAL & INSTALLATION. 2. Disconnect power window motor wire connector from door harness. 3. Using 2 jumper wires, connect one to a battery (+) source and the other to a good ground (-). 4. Connect the negative (-) jumper probe to one of the motor connector terminals.

Related entry:

wiring diagram for power windows on a 1990 astro van, power windows wiring diagram for a 1990 astro van, power distribution center chart 2000 town and country, power window diagram for 2001 astro, power windows diagram astro van, 2005 vw gti no power to ignition, replace window 94 astro van, sub chassi chevy astro van diagrams, trouble shooting 1996 camry lost power to windows ac, 01 sebring window wire code,

2007 Volkswagen Eos Side Window, Adjusting Information on adjusting

0

Filed Under (volkswagen) by admin on 28-06-2010

download
Before adjusting rear side window, door window adjustment must be checked and corrected if necessary. The rear side window is adjusted to the door window. The side window adjustment sequence is: 1. In direction of travel and in height to door window, 2. In angle. All adjustments and functions should be checked with roof closed and open. Window regulator basic setting NOTE: Window regulator motor must operate with greatest possible operating force for window regulator basic setting. Therefore, it is necessary to leave the engine running. CAUTION: Risk of injury! Window travel must be able to be blocked in advance of closing. Under no circumstances should you leave your hand on window and allow the window to close completely. Procedure for window regulator basic setting: Start engine. Completely lower side window. Close side window and block with hand. Side window lowers (reverses). Close side window again within 5 seconds and block with hand again. Side window stops. Close side window again within 5 seconds . Side window runs without pinch protection up to mechanical window regulator stop. Within 5 seconds , hold window regulator switch for 5 seconds . Now window regulator motor is adjusted to window regulator.

1995 Ford Contour Hoses Pressure and Return REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 15-02-2011

download
Removal 1. Disconnect battery ground cable. 2. Disconnect power steering pressure (PSP) switch electrical connector. 3. Remove power steering pressure (PSP) switch from power steering pressure hose. 4. On 2.0L engine, remove one nut, two bolts and disconnect power steering pressure hose from power steering pump bracket and engine lifting bracket. 5. On 2.5L engine, remove one bolt and disconnect power steering pressure hose from front engine support insulator. 6. Remove power steering pump auxiliary reservoir as outlined. 7. Raise vehicle on hoist. Refer to Section 00-02. 8. Remove front sub-frame. Refer to Section 02-01. 9. Remove six bolts and steering gear cover plate from front sub-frame. 10. Disconnect power steering pressure hose and power steering return hose unions from steering gear. 11. Remove two bolts retaining power steering pressure and return hoses to front sub-frame and remove power steering pressure and return hoses. CAUTION: Whenever the power steering pressure and return hoses and/or steering gear are disconnected, the power steering pressure and return hoses and/or steering gear should be plugged to prevent system contamination. If the power steering system becomes contaminated with dirt or other foreign matter, power steering pump and/or steering gear failure may result. Installation 1. Position power steering pressure and return hoses to front sub-frame and secure with two bolts. Tighten bolts to 28 Nm (21 lb-ft). 2. Connect power steering pressure hose and power steering return hose unions to steering gear. Tighten unions to 31 Nm (23 lb-ft). 3. Install steering gear cover plate and secure with six bolts. Tighten bolts to 50 Nm (37 lb-ft). 4. Install front sub-frame. Refer to Section 02-01. 5. Lower vehicle. 6. Install power steering pump auxiliary reservoir as outlined. 7. On 2.5L engine, connect power steering pressure hose to front engine suppor t insulator and secure with one bolt. Tighten bolt to 6 Nm (53 lb-in). 8. On 2.0L engine, connect power steering pressure hose to power steering pump bracket and engine lifting bracket. Secure with one nut and two bolts. Tighten nut and bolts to 6 Nm (53 lb-in). 9. Install power steering pressure (PSP) switch into power steering pressure hose. 10. Connect power steering pressure (PSP) switch electrical connector. 11. Connect battery ground cable. 12. Refill power steering fluid as necessary and bleed system. Refer to Section 11-00. Hose Fittings, Pressure and Return Line at Steering Gear and Pump

Related entry:

diagram of 2001 ford winstar power steering line, diagram of bracket for power stering 2001 venture, 2002ford windstar power steering switch location, pt cruiser power steering pump removal, 2000 Mazda MPV how to locate power steering fluid leaking, town & country seats want move, 350 Chevy Power Steering Diagram, hyundai tucson power steering leak, how to replace a power steering pressure switch on 04 grand marquis, hyundai tuscon power steering leak,

2008-2009 Pontiac G6 GXP 2008-2009 Pontiac G8 2008-2009 Pontiac Torrent GXP Intake System Throttle Body Spacer installation

0

Filed Under (Pontiac) by admin on 17-08-2010

download
Installation Instructions Part Number 200-630 2008-09 Buick Enclave 2008-09 Chevrolet Equinox Sp. 2008-09 Chevrolet Malibu 2008-09 Chevrolet Traverse 2008-09 GMC Acadia 2008-09 Pontiac G6 GXP 2008-09 Pontiac G8 2008-09 Pontiac Torrent GXP 2008-09 Saturn Outlook 2008-09 Saturn Vue XR 2008-09 Suzuki LX7 3.6L V-6 2. Disconnect the breather hose elbow from the intake tube. Loosen the two hose clamps that secure the intake tube to the throttlebody, and the mass air flow sensor. Remove the air intake tube. 1. Disconnect the negative battery cable! Remove the oil fill cap and set it aside. Lift straight up on the engine beauty cover and set it aside. Reinstall the oil fill cap after the beauty cover has been re- moved to prevent any foreign material from entering the crank- case. 3. Remove the four bolts that secure the throttlebody to the in- take manifold. 5. Install the provided bolts and washers thru the throttlebody and Poweraid Spacer and tighten to the manufacturer’s specifi- cations. 4. Install the Poweraid Spacer between the throttlebody and the intake manifold with the first supplied gasket next to the intake manifold, and the second supplied gasket next to the throttle- body as shown. Make sure the “flow” arrow printed on the spacer is pointing towards the intake manifold. 6. Reinstall the intake tube, tighten the two hose clamps, and reconnect the crankcase breather tube. Reinstall the beauty cover, and oil cap in the reverse order that they were removed. Re-connect the negative battery cable!

Related entry:

1994 pontiac transport repair manual, 2008 torrent misfiring, mitsubishi pajero 2008 manual download, replace 2008 yaris rotors, temperature actuator 2008 azeera, damaged crankshaft in a 2008 vitz engine, how to change a alternator in a 2008 pontiac wave, toyota axio 2008 manual, 2008 G6 timing belt mark, 2008 chevrolet idle speed relearn,