2008 pt cruiser fuse location
You are searching repair manual in PDF format about 2008 pt cruiser fuse location use another keyword for search another post or files
2008 pt cruiser fuse location Direct Download speed 5787 Kb/s
2008 pt cruiser fuse location Full Version speed 6767 Kb/s
Filed Under (Buick) by admin on 01-01-2011
SUBJECT: MODELS: Heated Windshield Washer Module Short Circuit – Add Wire Harness 2006-2008 model year Buick Lucerne; Cadillac DTS; HUMMER H2 vehicles; 2007- 2008 model year Cadillac Escalade, Escalade ESV, Escalade EXT; Chevrolet Avalanche, Silverado, Suburban, Tahoe; GMC Acadia, Sierra, Yukon, Yukon XL; Saturn OUTLOOK vehicles; and 2008 model year Buick Enclave vehicles equipped with a heated washer fluid system. A short circuit on the printed circuit board for the washer fluid heater may overheat the control-circuit ground wire. This may cause other electrical malfunctions, create an odor, or cause smoke. In rare cases, it may cause a fire. PARTS INFORMATION No parts are required to pull the heated windshield washer fuse. When wire harnesses are available for ordering, a revised bulletin with ordering information will be sent to dealers/retailers. SERVICE PROCEDURE Important: Until wire harnesses become available, the following procedure allows dealers/retailers to remove the heated windshield wiper fuse, disabling the system. 2007-2008 Cadillac Escalade, Escalade EXT, Escalade ESV, 2007-2008 Chevrolet Avalanche, Silverado (GMT900), Suburban, Tahoe, 2007-2008 GMC Sierra (GMT900), Yukon and Yukon XL 1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in SI. Important: The underhood fuse block is located in the engine compartment on the driver side of the vehicle. Refer to Underhood Fuse Block in the Owner’s Manual for fuse information. 2. Locate the underhood bussed electrical center (UBEC). 3. Remove the UBEC cover and locate the 60 amp heated windshield washer fuse. Important: Remove the two relays (1) next to the fuse to gain access to the fuse. 4. Remove the 60 amp heated windshield washer fuse (2) using needle-nose pliers. 5. Store the 60 amp heated windshield washer fuse in the glove compartment. 6. Install the two relays (1) removed in Step 4. 7. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in SI. 8. Test the operation of the windshield wiper system. 8.1 Ensure the wiper system functions in low and high positions. 8.2 Verify that the windshield wiper/washer switch functions. The windshield wiper system should provide wiper fluid to the windshield. 8.3 Ensure that the heated windshield washer fluid system has been disabled. • Verify that the heated windshield washer switch does NOT flash. 9. Secure the UBEC cover on the UBEC. 10. Close the hood.
Related entry: how to put refrigerant in a 2008escalade
, reverse light in prius 2008 and fuses
Filed Under (Mercedes-Benz) by admin on 10-05-2010
The fuse/relay box is located in the left side of the engine compartment. Relay and Control Unit Locations Fuse Box and Fuse Location (Fuses 1 – 4) Fuse Box and Fuse Location (Fuses G, H, F10, F15, F22, F22/1,
F22/2) Fuse Box and Fuse Location (Fuses F24 & F24/1)
Related entry: fuse location on engine toyota sienna 2005
Filed Under (Pontiac) by admin on 17-08-2010
Installation Instructions Part Number 200-630 2008-09 Buick Enclave 2008-09 Chevrolet Equinox Sp. 2008-09 Chevrolet Malibu 2008-09 Chevrolet Traverse 2008-09 GMC Acadia 2008-09 Pontiac G6 GXP 2008-09 Pontiac G8 2008-09 Pontiac Torrent GXP 2008-09 Saturn Outlook 2008-09 Saturn Vue XR 2008-09 Suzuki LX7 3.6L V-6 2. Disconnect the breather hose elbow from the intake tube. Loosen the two hose clamps that secure the intake tube to the throttlebody, and the mass air flow sensor. Remove the air intake tube. 1. Disconnect the negative battery cable! Remove the oil fill cap and set it aside. Lift straight up on the engine beauty cover and set it aside. Reinstall the oil fill cap after the beauty cover has been re- moved to prevent any foreign material from entering the crank- case. 3. Remove the four bolts that secure the throttlebody to the in- take manifold. 5. Install the provided bolts and washers thru the throttlebody and Poweraid Spacer and tighten to the manufacturer’s specifi- cations. 4. Install the Poweraid Spacer between the throttlebody and the intake manifold with the first supplied gasket next to the intake manifold, and the second supplied gasket next to the throttle- body as shown. Make sure the “flow” arrow printed on the spacer is pointing towards the intake manifold. 6. Reinstall the intake tube, tighten the two hose clamps, and reconnect the crankcase breather tube. Reinstall the beauty cover, and oil cap in the reverse order that they were removed. Re-connect the negative battery cable!
Filed Under (GM) by admin on 13-06-2010
GM Accessories Headrest DVD System Display Monitor Inoperative (Install Cable Connector Clamps) 2004-2007 Buick Rainier 2008 Buick Enclave 2003-2008 Cadillac Escalade Models 2005-2008 Cadillac CTS, SRX, STS 2006-2008 Cadillac DTS 2003-2008 Chevrolet Avalanche, Silverado, Suburban, Tahoe, TrailBlazer Models 2006-2008 Chevrolet Colorado 2007-2008 Chevrolet Equinox, HHR 2003-2008 GMC Envoy Models, Sierra, Yukon Models 2006-2008 GMC Canyon 2007-2008 GMC Acadia 2007-2008 Pontiac Torrent 2005-2008 HUMMER H2 2006-2008 HUMMER H3 2007-2008 Saturn OUTLOOK 2005-2008 Saab 9-7X Condition Some customers may comment on an inoperative display monitor or monitors in the GM Accessories Headrest DVD System. Cause This condition may be caused by a loose connection at the display monitor cable connectors. These connectors are located at the lower rear part of both front seats. Two cables are routed to the display monitor in each seat.
Filed Under (Infiniti) by admin on 18-05-2010
Electrical components are protected against shorts by fuses. Main fuse box is located in left kick panel next to park brake pedal. Fuse application information is located on fuse box cover. An underhood fuse and fusible link box is located next to battery. Relay boxes are located next to battery and on right side of engine compartment.
UNDERDASH FUSE PANEL FUSE & CIRCUIT BREAKER IDENTIFICATION