2010 ford festiva transmission dipstick location


You are searching repair manual in PDF format about 2010 ford festiva transmission dipstick location use another keyword for search another post or files



  2010 ford festiva transmission dipstick location Direct Download speed 5787 Kb/s

  2010 ford festiva transmission dipstick location Full Version speed 6767 Kb/s




2010 FORD Fusion 6F35 TRANSMISSION—RECREATIONAL TOWING— VEHICLE WITH ALL 4 WHEELS ON THE GROUND— EXPANDED GUIDELINES TO PREVENT TRANSMISSION DAMAGE

0

Filed Under (Ford) by admin on 03-12-2010

download
FORD: 2010 Fusion 2009-2010 Escape ISSUE Some 2009-2010 Escape, Mariner, 2010 Fusion and Milan vehicles equipped with a 6F35 automatic transmission, may experience transmission shift concerns after towing the vehicle with all 4 wheels on the ground (Flat tow) such as behind a motor home or a truck. The transmission shift concern may be caused by heat build up in the transmission due to the transmission fluid level being too high, towing speeds above 65 MPH (105 Km/h) and/or not stopping to run the engine at idle for 5 minutes every six hours or less, to cool the transmission. MERCURY: 2010 Milan 2009-2010 Mariner SERVICE PROCEDURE There are specific instructions listed in the Owner Guide that must be followed to recreational tow/flat tow/tow a vehicle with all 4 tires on the ground. Advise customers of the following expanded recreational towing guidelines. 1. Transmission fluid level must be checked at operating temperature of 185 °F – 200 °F (85 °C – 93 °C), per Workshop Manual (WSM), Section 307-01. At this temperature, adjust fluid level between minimum line and the minimum hole at the bottom of the hash marks on dipstick. This level is within the safe operating fluid level and does not require the customer to have the fluid level readjusted after flat tow operation. (Figure 1) 2. Maximum towing speed is 65 MPH (105 Km/h). 3. Do not flat tow the vehicle for greater than 6 hours at a time. 4. Start and run the engine for: a. 5 minutes before towing each day b. 5 minutes every 6 hours or less. c. While running the engine at idle for 5 minutes, with foot on the brake, shift through all gears. These guidelines are designed to prevent damage to the transmission due to overheating. If setting the fluid level for a customer that will be recreational (flat) towing the vehicle, set the level between minimum line and the minimum hole at the bottom of the hash marks on dipstick (Figure 1) per WSM Section 307-01.

Related entry:

1998 ford contour towing all 4 wheels on ground, wheel nut torque specifications 2010 chevy hhr, replace alternator 2010 milan, how to replace idler pulley ford fusion 2010, how long transmission to reach normal operating temp, chevy hhr lug nut torque, 2010 traverse ac lines diagram, 2010 tahoe freon takes, 2010 Ford Fusion Shop Manual, who builds ecm for 2010 ford fusion,

2003-2005 Chevrolet TrailBlazer Automatic Transmission/Torque Converter Clutch (TCC) Shudder

0

Filed Under (Chevrolet) by admin on 30-12-2010

download
Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Condition Some customers may comment on a shudder condition at approximately 64-80 km/h (40-50 mph) when the TCC engages. Cause This condition may be caused by water in the automatic transmission fluid (ATF). Water may enter the transmission by dripping from the cowl area onto the handle of the transmission fluid level indicator. Indications of water in the ATF may include: • Visible rust on the transmission fluid level indicator. • Visible water in the oil pan. • A milky white substance inside the pan area. • Spacer plate gaskets that appear to be glued to the spacer plate, valve body or case. • Rust on internal transmission iron/steel components. Correction First, repair the transmission and second, replace the transmission fill tube, seal and level indicator to prevent repeat water contamination of the ATF. Transmission Repair 1. Remove the transmission. Refer to the appropriate SI procedure. 2. Disassemble and inspect the transmission. Refer to Unit Repair Automatic Transmission – 4L60-E/4L65-E. Important: If water or coolant is found in the transmission, the following components MUST be replaced. • Replace all of the rubber type seals. • Replace all of the composition-faced clutch plate assemblies including the band. • Replace all of the nylon parts (Thrust Washers). • Replace the torque converter. • Thoroughly clean and rebuild the transmission, using new gaskets and oil filter. • Flush and flow check the transmission oil cooler using J 45096. Refer to Corporate Bulletin Number 02-07-30- 052C or newer – Automatic Transmission Oil Cooler Flush and Flow Test Essential Tool J 45096 TransFlow . Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator WITH the transmission REMOVED from vehicle. 1. Remove the transmission fluid filler tube from the transmission. 2. Replace the transmission fill tube seal, P/N 1259475. 3. Replace the transmission fill tube, P/N 15000220, following the appropriate SI Document for Transmission Installation. 4. Replace the transmission fluid level indicator, P/N 15069769 when appropriate during the transmission installation. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator with the transmission in the vehicle. 1. Remove the air cleaner outlet duct. Refer to Air Cleaner Element Replacement (SI Document ID# 1364496). 2. Remove the transmission fluid level indicator from the filler tube.

Related entry:

2000 ford focus transmission removal, turbo 400 transmission diagram, ford transmission parts diagram 1997 ford 4r/55e, 2000 cadillac deville transmission removal, where is the transmission vent located on a 2002 ford escape, what vehicles all have re4f04a transmission, 2001 international 4700 check trans light, auto trans fluid filling plug in 2011 sorento, Digrams For Automatic Transaxle for 2005 Bonneville Pontiac, diagram 2002 hyundai elantra manual transaxle,

2006 Ford Crown Victoria Automatic Transaxle/ Transmission REMOVAL

0

Filed Under (Ford) by admin on 19-02-2011

download
NOTICE: Whenever a transmission has been disassembled to install new parts, the transmission fluid cooler tubes must be cleaned and backflushed using a suitable torque converter/fluid cooler cleaner. A new Oil-To-Air (OTA) transmission fluid cooler must also be installed. When internal wear or damage has occurred in the transmission, metal particles, clutch plate material or band material may have been carried into the torque converter and fluid cooler. These contaminants are a major cause of recurring transmission concerns and must be removed from the system before the transmission is put back into service. NOTE: After the transmission is removed for a major overhaul, it is important to completely clean all transmission components, including torque converter, cooler inlet tube, main control valve body, clutches and all coasting booster valve shuttle balls after any transmission service that generates contamination. These contaminants are a major cause for recurring transmission concerns and must be removed from the system before the transmission is returned to service. The cleaning of foreign material from the direct clutch check ball is often omitted. This omission can lead to a repeat servicing of the transmission. A new Oil-To-Air (OTA) transmission fluid cooler must be installed under the following condition. For additional information, refer to Section 307-02. Evidence of broken transmission components or transmission fluid contamination found due to the following transmission or converter failure modes: Major metallic failure Multiple clutches or clutch plate failure Sufficient component wear which results in metallic contamination 1. Disconnect the battery ground cable. For additional information, refer to Section 414-01. 2. WARNING: Before servicing a vehicle equipped with a fire suppression system, depower the system by following the procedure in Section 419-03. Failure to follow the instructions may result in serious personal injury. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section 100-02. 3. NOTE: Only if transmission disassembly or replacement is required, drain the transmission fluid. For additional information, refer to Fluid Pan, Gasket and Filter in this section. Drain the transmission fluid. Loosen the transmission fluid pan bolts and allow the transmission fluid to drain. After transmission fluid has drained remove the bolts and the pan and drain the remaining transmission fluid that is in the pan. 4. Install the transmission fluid pan and the old transmission fluid pan gasket. 1. Position the transmission fluid pan gasket. 2. Position the transmission fluid pan. 5. NOTE: To maintain the initial driveshaft balance, mark the rear driveshaft yoke and the axle pinion flange so they can be installed in their original positions. Mark the rear driveshaft yoke and the axle pinion flange and remove the 4 bolts.

Related entry:

how to remove the valve body of a 2005 pacifica transmission, 1975 ford maverick engine schematic, Chevy carveler transmission revove, 2003 Ford Escape Transmission Removal, removing transaxle from a 2003 rav 4 awd, 2002 ford escape transmission diagram, remove transmission from bmw 745, 94 chevy transmision removal, Engine and transmission removal 3 8 bonneville 2000, chevy metro automatic transmission removal,

2006 Ford Explorer Transmission Fluid Refill procedure

0

Filed Under (Ford) by admin on 07-03-2011

download
Transmission Fluid Refill NOTICE: This procedure contains the air purge steps required to purge air from the cooling system. This procedure is NOT intended for use with the Transmission Fluid Level Check. NOTICE: The vehicle should not be driven if the fluid level is low as internal failure could result. NOTICE: The fluid fill plug is located near the exhaust system. The exhaust will be extremely hot during this procedure. NOTICE: The use of any other transmission fluid than specified, can result in the transmission failing to operate in a normal manner or transmission failure. NOTE: If the transmission starts to slip, shifts slowly or shows signs of fluid leaking, the fluid level should be checked. NOTE: Here is an overview of the Transmission Fluid Drain and Refill procedure. Adding 3.3L (3.5 qt) of clean automatic transmission fluid to the transmission is an initial fill enabling you to start the engine. The cold level range shown in the procedure allows the vehicle to be driven. The vehicle should be driven to allow the transmission fluid temperature to reach 85ºC-88ºC (185ºF-190ºF) in order to purge the air from the transmission cooling system. Fill the transmission fluid to the fill range on the fluid level indicator at the normal operating range 80ºC-85ºC (175ºF-185ºF). 1. NOTE: The transmission will need 3.3L (3.5 qt) of clean automatic transmission fluid added to the transmission as an initial fill if: the transmission has been overhauled. a new mechatronic assembly has been installed. the transmission fluid pan or fluid filter have been removed. Using the special tool, add 3.3L (3.5 qt) of clean automatic transmission fluid to the transmission through the fluid fill hole. For additional information, refer to Adding Additional Transmission Fluid in this procedure. 2. Check the transmission fluid level cold. 1. The vehicle is safe to drive if the transmission fluid is in the cold level range 32°C-43°C (90° F-11 0° F). Using the scan tool and the engine running, place the transmission selector lever in each gear position and hold approximately 5 seconds. Place the transmission selector lever in PARK, with the engine at idle (600-750 rpm).

Related entry:

09G Transmission Fluid Fill Procedure, Kia ATF 6S SP-4 MSDS, 2006 chevy hhr transmission fluid change, how di i change trannyfluid on 2006 equinox, 2004 tahoe transmission fluid check, hot to change transmission filter on 2005 chevy equinox, change trans filter 2007 expedition, 2005 CADILLAC SRX TRANSMISSION OIL, 2005 Suzuki Forenza adding tranmission fliud, checking transmission fluid level on a 2011 caravan,

2006 Ford Freestyle Transmission Fluid Drain and Refill GENERAL PROCEDURES

0

Filed Under (Ford) by admin on 31-03-2011

download
NOTICE: The use of any fluid other than what is recommended for this transmission will cause transmission damage. Draining 1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section 100-02. 2. Remove the transmission fluid drain plug and allow the transmission fluid to drain. Refill 3. Install the transmission fluid drain plug. Tighten to 47 Nm (35 lb-ft). 4. Remove the transmission fluid fill plug. 5. Fill the transaxle with approximately 3.7L (4 qt) of clean transmission fluid. 6. Install the transmission fluid fill plug. Tighten to 39 Nm (29 lb-ft). 7. With the transaxle in (P) PARK, the vehicle should be on a level surface, the engine at idle (680-780 rpm), foot pressed on the brake, move the selector lever through each gear and allow engagement of each gear. Place the selector lever back in the PARK position. 8. Wipe the transmission fluid level indicator cap and remove the fluid level indicator. 9. Wipe the transmission fluid level indicator with a clean cloth. 10. NOTE: In order to get an accurate transmission fluid level reading, the vehicle should be on a level surface, the engine at idle (680-780 rpm) for 5 minutes and the transmission fluid temperature should be at least 70°C-80° (158° C F-176° using the scan tool. F) If transmission fluid needs to be added, add transmission fluid in 0.25L (1/2 pint) increments through the transmission fluid fill plug located on the top of the transaxle near the transmission fluid level indicator. Do not overfill the transmission fluid. Install the transmission fluid level indicator back in the transmission fluid filler tube until it is fully seated, then remove the indicator. The transmission fluid level should be at the upper-most mark on the transmission fluid level indicator. Only fill to the upper-most mark on the transmission fluid indicator. Do not overfill. Damage to the transaxle will occur.

Related entry:

TORQUE REQUIRED FOR 2008 TOYOTA SIENNA TRANSMISSION DRAIN PLUG, renault traffic transmission fluid, 2004 kia optima transaxle fill plug, automatic transmission repair on automatic honda stream, transmission drain plug on 2007 ford edge, how to check transmission fluid on a 2007 pntiac torrent, Ford Taurus Transmission Fluid Capacity, ford freestyle transmission removal, how much to rebuild transmission for 2005 ford freestyle, ford freestyle high pressure filter,