Auto Repair Manual Free Download and ReviewsFree download ebook pdf files automotive manual

download
Removal of Factory Intake 1. 2. Pull upwards to remove the engine cover. Unclip the battery cover and remove, then disconnect the negative battery cable. Disengage the plastic rivet. Slide the battery cold air vent backwards and remove from the engine compartment. Disconnect the mass air sensor electrical connection. Depress the retaining clip and disconnect the rank case vent hose from the stock intake tube. Remove the switch/sensor from the air cleaner cover. Loosen the clamp at the throttle body. Unclip the coolant hose from the air cleaner cover. Unclip the air cleaner cover and remove the complete upper air cleaner assembly. Remove the rubber retainer from the core support. Remove the lower air cleaner assembly. Unclip the wire harness from the side of the battery box. Remove the mass air sensor from the air cleaner cover. Remove the plastic clip from the crank case vent on the stock intake tube. Slide the clamps off rubber rank case vent. Remove the plastic vent from the stock intake tube. Slide the plastic clip from before back onto the crank case vent. Raise the vehicle up and support by jack stands, then remove the left front tire. Remove the four bolts and one plastic rivet from the inner valance, then remove the valance. Remove the three plastic rivets and six hex bolts on the inner valance, then pull the inner valance downward. Remove the three bolts that secure the air intake resonator to the inner fender, then remove the resonator. Secure the rubber mounted stud to the hole on the battery tray. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. Install of Intake 24. Install reducer and clamps onto the throttle body. 25. Install the hose onto the vent on the intake tube. 26. Install the mass air sensor into the intake tube. 27. Slide the tube into the reducer and line up the bracket with stud, then tighten the clamps at the throttle body. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. 38. 39. 40. Secure the switch to the bracket (not for the 06 Mazda 5 model). Install the crank case vent into the hose on the intake tube. Reconnect the crank case vent. Install the rubber mounting stud into the resonator threaded hole. Install the reducer and clamps onto the cold air tube. From underneath the vehicle install the cold air tube. Slide the cold air tube onto the short ram tube. Secure the bracket to the tuber mounted stud. Install the filter onto the cold air tube from the underneath vehicle. Reconnect the mass air sensor. Reverse the removal process and reinstall the inner fender valance. Reinstall the front tire and torque to factory specs. Slide the vent into the core support and line up the other end with the battery box and secure with plastic rivet. 41. Reconnect the negative battery cable, then reinstall the battery cover. 42. Reinstall the engine cover. Resetting the ECU This is to be completed at your own risk. This procedure will reset the computer so that it may “learn” of your new intake. We are not to be held liable for any mishaps that you may occur while completing this process. • • Disconnect the Negative battery cable for 5 minutes. Reconnect the battery cable and false panel cover.

download
Torque Specs always torque bolts in three equal increments Lube or Sealer Torque to: Engine Oil 105 ft-lbs. Connecting Rod Bolts Engine Oil 45 ft-lbs. Engine oil 140 ft-lbs. (blind hole) (water jacket) Rocker Arms (non-adjustable) Engine Oil 20 ft-lbs. Engine Oil 25 ft-lbs. Engine Oil 15 ft-lbs. Cam Bolt (upper gear) Thread Locker 45 ft-lbs. Engine Oil 20 ft-lbs. Non- Hardening 30 ft-lbs. Sealer Engine Oil 10 ft-lbs. Flexplate (Automatic) Thread Locker 85 ft-lbs.

download
1. Remove both front wheels from the car. 2. Unclip the hard plastic breather hose from the breather nipple by squeezing the blue retaining clip. 3. Lift up and remove the steel bracket securing the purge solenoid valve (PSV) to the inlet hose. Leave the PSV attached to the valve and move it out of the way. 4. Unplug the MAF sensor from the wiring harness. 5. Unclip the MAF sensor wiring harness from the side of the air filter housing 6. Loosen the hose clamps securing the inlet hose to the throttle body and the air filter housing. Remove the inlet tube.(View B, #5) 7. Remove the air filter housing lid (View B, #1) by unhooking the metal retaining clips and sliding the lid out. 8. Remove the air filter element (View B, #2). 9. Remove the lower air filter housing (View B, #3) by removing the two nuts securing the housing to the chassis. Next, lift up on the back side of the housing and remove it from the vehicle. 10. Remove the retaining clips and bolts securing the driver and passenger side splash shields to the bumper and chassis. Remove the splash shields. 11. Disconnect the front fog light connectors for vehicles equiped with fog lights. 12. Disconnect the side marker light connectors. View C: Bumper Removal / Installation 13. Remove the parts in the order indicated in Table A: 14. Remove the fresh air duct by removing the two plastic clips and the bolt securing it to the chassis (View B,#6). 15. Remove the plastic fasteners (View D, #1) securing the plastic shroud seal plate (View D, #2) between the steel bumper support (View D, #4) and the chassis. 16. Unhook the wiring harness from the horn and unclip it (View D, #3) from the bumper support. 17. Remove the 8 bolts securing the bumper support to 7.8-11.8 the chassis. Remove the bumper support. {80-120, 18. Remove the stock MAF sensor from the air filter 70-104} housing lid (View B, #1). 19. Remove the plastic breather nipple, spring clamp, and two hose clamps from the stock inlet hose. 1. Install the plastic breather hose nipple (View E, #2) removed in step #18 into the supplied throttle body coupler (View E, #3) and secure using the stock spring clamp (See View F). 2. Install the two hose clamps removed in step #18 (View B) onto the supplied throttle body coupler. Install the coupler onto the throttle body. Do not tighten hose clamp. 3. Install the steel PSV bracket (View E, #1) from the stock inlet tube by sliding it into the mount on the throttle body coupler. Be sure bracket is fully seated at top guide pin. 4. Plug the plastic breather hose onto the nipple. Be sure both the breather hose and PSV bracket are secure before proceeding. 5. Install the MAF sensor into the upper intake pipe (View E, #4) and secure using the two supplied 8-32 bolts (View E, #5). Torque the bolts to 12-15 in-lbs (1.4-1.7 N-m).

download
TORQUE SPECIFICATIONS Application A/C Compressor Bracket Bolts Upper Vertical Bolt Horizontal Bolts A/C Compressor-To-Bracket Bolts Air Inlet Tube-To-Supercharger Bolts Camshaft Locating Plate Bolt Camshaft Sprocket Bolt Connecting Rod Nuts Step 1 Step 2 Coolant Outlet-To-Intake Manifold Bolts Crankshaft Pulley Bolt Cylinder Block Coolant Drain Plug Cylinder Head Bolts (2) Step 1 – Cylinder Head Bolts Step 2 – Cylinder Head Bolts Step 3 – Cylinder Head Bolts Step 4 – Cylinder Head Bolts Step 5 – Intake Manifold Bolts/Nuts (3) Step 6 – Intake Manifold Bolts/Nuts Step 7 – Intake Manifold Bolts/Nuts Step 8 – Intake Manifold Bolts/Nuts Step 9 – Cylinder Head Bolts Step 10 – Cylinder Head Bolts Step 11 – Cylinder Head Sub-Bolts Step 12 – Intake Manifold Bolts/Nuts Step 13 – Intake Manifold Bolts/Nuts Step 14 – Intake Manifold Bolts/Nuts Distributor Hold Down Bolt EGR Pipe

download
REMOVAL 1. Remove the engine cover. 2. Disconnect ETS connector (A) 3. Disconnect CMP connector (A), and knock sensor connector (B). 4. Disconnect injector connector (A). 5. Remove the delivery pipe (A), brake vacuum hose (B), and PCSV hose (C). 6. Remove coolant hose (A) from throttle body. 7. Remove oil pressure switch connector (A) from bracket. 8. Remove knock sensor connector (A) from bracket. 9. Remove PCV hose (A). 10. Remove oil level gauge. 11. Remove intake manifold stay (A). 12. Remove intake manifold (A) and gasket (B). INSTALLATION 1. Install intake manifold. Tightening torque 18.62 – 27.44 Nm (1.9 – 2.8 kgf.m, 13.7 – 20.2 ft. lbs.) 2. Install intake manifold stay. Tightening torque 18.6 – 27.44 Nm (1.9 – 2.8 kgf.m, 13.7 – 20.2 ft. lbs.) 3. Install oil level gauge 4. Install PCV hose 5. Install air cleaner assembly 6. Install engine cover.