Auto Repair Manual Free Download and ReviewsFree download ebook pdf files automotive manual

download
- with CODE (848) Electric pivoting side window Remove/Install 1 Remove paneling on C-pillar 2 Secure window against falling down. NOTE: To avoid damage to window or paintwork 3 Unscrew bolts (A) at hinges Screw for side window hinge to C pillar = 12 Nm 4 Pull back cover at opening mechanism Pull back cover at opening mechanism NOTE: For access to connecting point at opening mechanism. 5 Remove window NOTE: Caution: Do not damage window and paint if adhesive tape or support is removed Extend window toward top (B). Check seal. If necessary, replace seal of side window. 6 Install in the reverse order

download
- with CODE (U49) Styling Package Remove/Install 1 Remove cover (1) from bumper NOTE: Do not break retaining lugs. 2 Remove bulb housing (2) NOTE: To unlock, rotate counterclockwise. Installation: Ensure that the locking device has locked securely. 3 Remove fog lamp insert (6) from housing Installation wedge: See Special Tools below. 4 Disconnect connector (4) 5 Remove bulb on the back of the fog lamp insert (6) CAUTION: Do not hold the bulb with bare fingers, as fingerprints bake and leave behind opaqueness on the bulb. Use a soft, lint-free cloth. NOTE: Lock securely. 6 Install in the reverse order Special Tools

download
AR68.20-P-2020GI Remove/Install Rear Center Console – Models 163.154/174 #A as of 289565 – Models 163.157/175 (all) Remove/Install 1 Remove armrest lid (1) 2 Remove stowage box in the center console NOTE: Press the center pin approx. 4 mm downwards, then remove the rivet upwards 3 Remove screws (2) on the cup holder 4 Remove inner part of ashtray 5 Remove ashtray trim (3) CAUTION: Risk of breaking the clips (4) NOTE: Loosen clips (4) and pull back the lower edge of the cover and remove upwards 6 Remove screws (5) 7 Unclip rear center console (6) above (arrows) Long wedge: See Special Tools below. 8 Remove rear center console (6) from the center console 9 Disconnect plug from control module of rear control panel and ashtray NOTE: Disconnect plug of the rear ashtray from ashtray housing 10 Install in the reverse order Special Tools Long Wedge P/N # 115 589 03 59 00

download
Table of contents A. B. C. D. E. F. Front bumper removal Lower Side Vent Grille Install Lower Center Grille Install Main Grille Install Front bumper Install Side Vent modifications for fog lights A. Front bumper removal. Tools Reqd: ratchet with 8mm and 10mm sockets (extension not required), small flat blade screwdriver, small phillips head screwdriver. Open the hood and prop it up. Remove the four 10mm bolts (see photo) Remove the quick-lock fasteners holding the weather trim piece in place. They are removed using a small Phillips screwdriver. Remove the 4 quick-lock fasteners in the passenger fender wheel (see photo). Using a Phillips head screwdriver, to back the center out (you may need to hold the outer ring to prevent it from turning) then pull the center out and then the outer ring. Repeat this for the driver’s side as well. Pull back the underpinning in the fender wells to locate the 8mm fastener that holds the side markers (orange lenses). Once the fastener is removed, a tab (see sub photo) must be released by pressing it down while pulling the side marker outward. The side marker is then slid to the rear to fully remove. Looking under the front end of the car you will find ten 8mm screws that hold the front bumper to the underpinning (see photo). At this point the front bumper cover is held in place merely by a locating pin that is beneath the trim at the top. Pull the bumper cover away from the fender on both sides at the side markers then proceed to lift the bumper cover upward and forward. At this point if you have fog lamps you will need to remove the wiring connectors. Place the front bumper cover on a padded surface to prevent scratching. You should now have something like this (minus the snazzy new grille).

download
1. Vehicle Disassembly (a) Set parking brake. (b) Remove the negative battery cable. (Fig. 1-1) (1) Protect the fender before starting. (2) Do not touch the positive terminal with any tool when removing cable. (c) Remove instrument panel garnish LH: (1) Disengage the 2 clips and remove the instrument panel garnish. (Fig. 1-2) NOTE: Pull the instrument panel garnish up at a 45º angle to remove it. (d) Remove instrument panel garnish RH: (1) Disengage the 2 clips and remove the instrument panel garnish. (Fig. 1-3) (e) Remove floor shift position indicator for automatic transmission. (1) Unscrew shift knob. (2) Disengage the 6 claws and 3 clips and remove assembly. (Fig. 1-4) (3) Disconnect any connectors. (f) Remove upper console shift boot panel for manual transmission. (1) Unscrew shift knob. (2) Disengage the 2 claws and 5 clips with panel removal tool & remove panel. (Fig. 1-5) (g) Remove center console garnish on automatic transmission. (1) Disengage the 3 claws and 5 clips with panel removal tool. (Fig. 1-6) (2) Disengage clamp. (3) Disconnect connector and remove garnish.