93 ford aerostar gear shift repair


You are searching repair manual in PDF format about 93 ford aerostar gear shift repair use another keyword for search another post or files



  93 ford aerostar gear shift repair Direct Download speed 5787 Kb/s

  93 ford aerostar gear shift repair Full Version speed 6767 Kb/s




1993 Mitsubishi Montero TRANSFER CASE DISASSEMBLY

0

Filed Under (Mitsubishi) by admin on 30-12-2010

download
Disassembly (Ram-50) 1) Remove both 4WD indicator switches and steel balls. Remove speedometer gear assembly. Remove output shaft cover, gasket, wave spring and spacer. See Fig. 3. Remove rear cover, rear cover gasket and spacer from chain cover. Drive roll pin out of high-low shift fork. 2) Remove 2 seal plugs. Remove 2 poppet springs and steel balls. Shift transfer case to “4WD” and pull high-low shift rail out, in rear cover direction. Remove interlock plunger. Remove pulse generator (if equipped), front output shaft cover and pulse rotor (if equipped). Remove snap ring from rear bearing on output shaft. Remove chain cover, oil guide and side cover. Remove countershaft locking plate. Remove countershaft. 3) Remove countergear, 2 thrust washers, 2 needle bearings and spacer through side cover opening. Remove snap ring, spring retainers and spring from 2WD-4WD shift rail. Remove front output shaft, rear output shaft and chain as assembly. 4) Remove 2WD-4WD shift fork and distance piece. Drive out 2WD-4WD shift rail spring pin. Remove 2WD-4WD shift rail and lug. Remove high-low shift fork and high-low synchronizer sleeve. Remove needle bearing and snap ring from input gear. Remove input gear assembly. 5) If either control shaft or input gear oil seals are to be replaced, drive out roll pin from transmission control change shifter. Separate transfer case from adapter. See Fig. 3. Disassembly (Montero) 1) Remove dynamic damper, 5 detection switches and 3 steel balls. Remove poppet plug, spring and steel ball. Remove speedometer gear assembly. Remove output shaft rear cover, spacers, dust seal guard and oil seals. Front output shaft cover, wave spring and spacer (if equipped). 2) Remove high-low shift rail plug and high-low shift fork spring pin. Shift transfer case to “4WD”. Remove rear cover and high- low shift rail. Remove interlock plunger. Remove rear output shaft (viscous coupling) assembly and center differential assembly. Remove 2WD-4WD synchronizer assembly, chain and front output shaft from transmission as a unit. With White paint make match marks in grooves of 2WD-4WD synchronizer in 3 places. With White paint make match marks on spline projections of 2WD-4WD synchronizer sleeve in 3 places. Refer to match marks during reassembly. 3) Remove snap ring, spring seat, spring, 2WD-4WD shift fork and 2WD-4WD synchronizer sleeve. Remove differential lock hub, oil dam cover and bearing retainer. Remove side cover and gasket. Remove transfer counter gear shaft, transfer counter gear, thrust washer, needle bearings and spacer. Remove transfer drive shaft assembly. Remove high-low shift fork assembly and clutch sleeve. Remove transfer input gear assembly. 4) Remove 2WD-4WD shift lug spring pin, spring, spring retainer 2WD-4WD shift lug and shift rail. Remove input gear oil seal, baffle plate, dust seal guard and front output shaft oil seal. See Fig. 4.

Related entry:

vw t4 gear lever removal, steps for disconnecting the electrical connectors on the back of the steering wheel airbag on a 2000 Chevy Venture, 1996 VW Golf Manual Shift Linkage, f250 ashtray removal, how to remove a visor from a subaru outback, How to replace an antenna on a S10 blazer, disconnect anti theft fuse on 1991 sadandiville diagram, Remove Snap ring on 2004 toureg drive shaft, c220 front spring removal, 2010 toyota yaris radiator removal how to,

2006 Pontiac GTO Transmission Jumps Out of Gear

0

Filed Under (Pontiac) by admin on 31-10-2010

download
If the transmission jumps out of gear during deceleration, inspect the components that may allow for the gears or shafts to tip. If the gears or shafts tip, the synchronizer sleeve can disengage from the selector teeth on the speed gear. If the transmission jumps out of gear during acceleration, inspect the components that may not allow full engagement of the synchronizer sleeve to the selector teeth on the speed gear. Insufficient engagement of the selector teeth under torque may cause the transmission to jump out of gear. Test Description The numbers below refer to the step numbers on the diagnostic table. 2. A static shift test is performed by shifting into all gear positions with the engine not operating. While performing the test, slowly move the shift lever. Feel for proper movement of the shift lever and transmission internal shift components. 4. A dynamic shift test is performed by shifting into all gear positions with the engine operating. Test for the correct mesh of the synchronizers sleeve and the speed gear selector teeth. Move the shift lever, and feel for the synchronizer sleeve to release from the gear, then let up on the clutch pedal. Depress the clutch pedal and move the shift lever to engage the gear again, to ensure full travel of the shift components. 5. This step inspects for worn or damaged transmission or engine mounts. Loose mounts may cause a shock on the transmission allowing for gear disengagement. 6. This step inspects for the misalignment of the torque tube to transmission. Misalignment may put a bind on the input shaft, allowing for the input shaft or the mainshaft to tip. 8. This step inspects the pilot bearing and the pilot bearing journal on the input shaft. A worn pilot bearing or input shaft may allow the input shaft to tip, causing gear disengagement.

Related entry:

adjust shifter 05 chevy aveo, 1997 geo tracker driven gear, ADJUST SHIF LINKAGE 05 AVEO, fixing corsa c gear link adjustment,

Ford / Mercury / Lincoln Band-Mounted Sensor Re-Learn Instructions

0

Filed Under (Ford, Lincoln) by admin on 17-10-2009

The instructions below can be used for the following vehicles: 2008 Ford Crown Victoria / Lincoln Town Car / Mercury Grand Marquis 2008 Ford E-series 2007-2009 Ford Edge / Lincoln MKX 2005-2008 Ford Escape / Mercury Mariner 2007-2009 Ford Expedition / Lincoln Navigator 2006-2009 Ford Explorer / Lincoln Aviator / Mercury Mountaineer 2007-2008 Ford F150, F250, and F350 / Lincoln Mark LT
2009 Ford Flex 2008-2009 Ford Focus 2006-2007 Ford Freestar / Mercury Monterey 2008-2009 Ford Fusion / Lincoln MKZ / Mercury Milan 2007-2009 Ford Mustang 2007-2009 Ford Ranger 2008-2009 Ford Taurus / Mercury Sable

1. Make sure all tires are inflated to the vehicle’s recommended inflation pressures (found in the owner’s manual on the door placard). 2. Turn the ignition switch to OFF then press and release the brake pedal. 3. Turn the ignition switch from OFF to RUN (engine OFF) 3 times, ending in the RUN position. Do this within 10 seconds. 4. Press and release the brake pedal

download

Related entry:

1997 Lincoln Repair Manual Free, Diagram of Ford E350 replacing Canister Purge Valve Solenoid, 2005FordKAEngineManagementWiringDiagramFreePDF, 1992 Ford Explorer Owners Manual, 1996 f 150 ac capacity, 1992 Ford Explorer Manual, idle speed relearn f150, 7 3 idi manuel, replace alternator 2009 fusion 2 3lt, removal of intake plenum on a 1989 Mercury Gran Marquis,

1986 Chevy Truck C 10 P/U Steering Column: Service and Repair Assembly

0

Filed Under (Chevrolet) by admin on 29-08-2010

download
1. To assemble bearing housing, proceed as follows: a. Using a suitable socket, press bearings into bearing housing. b. Install lock shoe springs, lock shoes and shoe pin into bearing housing. c. Install shoe release lever, spring and pin. d. Install sector drive shaft and snap ring into housing. e. Install lock bolt and engage bolt with sector cam. f. Install rack and spring. Block tooth on rack should engage block tooth on sector. g. Install tilt release lever. h. Install lock bolt spring and retaining bolt. Torque bolt to 35 inch lbs. On C, G and K models, install shift lever spring into housing. On Caballero and El Camino models, install shift lever spring into shift bowl. Install bearing support lock plate and wave washer. On C, G and K models, carefully install shift tube into lower end of steering column jacket. Install wobble plate end of tool J-23073 into upper end of shift tube. Install adapter over end of tube, seating it against the lock plate. Place nut onto threaded portion of tool and pull shift tube into housing. Remove tool. On Caballero and El Camino models, install bearing support thrust washer and retaining ring. Carefully install shift tube into lower portion of steering column jacket. Align shift tube key with shift bowl keyway. Using tool J-23073, pull shift tube into the shift bowl. Install thrust washer and retaining ring. Install actuator rod through support hole between shift bowl and steering column jacket. Install bearing support. Align bearing support “V” with “V” on steering column jacket. Install attaching bolts through support and into lock plate. Torque attaching bolts to 60 inch lbs. Align lower bearing adapter or bushing with notches in steering column jacket. Install lower bearing, bearing reinforcement and retaining clips. Ensure clips align with reinforcement slots on steering column jacket and adapter assembly. Install centering spheres and anti-lash spring onto upper shaft. Install lower steering shaft assembly. On C, G and K models, install steering shaft assembly into shift tube. Install ignition switch actuator rod through shift lever housing. On Caballero and El Camino models, position shift bowl into Park (counterclockwise to stop). Install ignition switch actuator rod between shift bowl and steering column jacket. Assemble bearing housing over steering shaft and engage rack over actuator rod end. On Caballero and El Camino models, position access hole of bearing housing over dimmer switch actuator rod end. While holding the locking shoes in the disengaged position, install bearing housing over steering shaft until pivot pin holes align with holes in support assembly. Install pivot pins. Place bearing housing in the full up (tilt) position. Install tilt lever spring guide, spring and spring retainer. On C, G and K models, proceed as follows: 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17.

Related entry:

installing camber bolts n 99 suburban, mazda cx7 front license bracket instructions, how to install a front license plate on a 2004 mazda 6, repair shift assembly jeep patriot, how to install a center support bearing on a 2004 dodge 3500, instal shocks on 2003 trailblazer, HOW TO ALIGN A TRAILBLAZER, How to Fix your TrailBlazers 2006 Shift linkage / bushing, how to change a shift bushing on a 2003 cavalier, how to install headliner in 63 vw bus,

2005 Ford Expedition, Ford F-250, Ford F-350 TICKING AND/OR KNOCKING NOISE FROM ENGINE

0

Filed Under (Ford) by admin on 07-09-2010

download
FORD: 2005 Mustang 2004-2005 F-150 2005 Expedition, F-250, F-350 This article supersedes TSB 05-15-8 to update the Service Procedure. ISSUE Some vehicles equipped with a 4.6L 3-valve or 5.4L 3-valve engine may exhibit a ticking and/or knocking noise after reaching normal operating temperature. The noise may be described as “ticks”, “taps”, “knocks”, or “thumps”. In some cases the noise may be a normal characteristic of these engines. In other cases the noise may require further investigation. Sorting out and defining the noise as reported by the customer is important to successfully diagnose and/or repair the condition. ACTION Before starting diagnosis, it is critical to determine the specific engine noise the customer is concerned with. The customer should be interviewed to get their detailed perception and description of the noise, and to determine if the noise occurs at idle or above idle speed, and if the engine is cold, hot, or both. Attempt to duplicate the noise, and determine the source of the symptom. Refer to the following Service Procedure to help determine the source of the noise and if a repair is needed. LINCOLN: 2005 Navigator PRE-CHECKS 1. 2. 3.

Related entry:

2007 ford exployer noise when starting, radiator diagram for 2001 7 3, 2004 ford f250 front schematic, INTERMENIT TICKING NOISE IN ENGINE WHEN STARTING 2011 FORD ESCAPE, schematic diagram of the motor on a 2005 ford expidition, 2000 ford excusrion shift solenoid, expedion tcc repacement, 1997 Ford Expedition AC Recharge, how to change a pvc hose on 2001 ford expedtion, 4 6 3 valve v8 on 2007 ford explorer ticking noise,