95 chevy truck rear brake diagram


You are searching repair manual in PDF format about 95 chevy truck rear brake diagram use another keyword for search another post or files




2010 Toyota Prius Rear Brake Squeak

0

Filed Under (Toyota) by admin on 09-05-2011

download
Introduction Some 2010 Prius vehicles may experience rear brake squeak when backing up or moving forward during the ?rst few brake applications when the brakes are cold. An updated rear brake shim kit is available to reduce the likelihood of this condition occurring. Repair Procedure 1. Test drive the vehicle to con?rm the squeak is coming from the rear brakes. The condition occurs more frequently when backing up during light brake pedal application after cold soak. 2. Remove rear brake shims. Refer to the Technical Information System (TIS) 2010 Prius Repair Manual: Brake – Brake (Rear) Brake: Rear Brake: Removal 3. Clean the rear brake pad backing plates with a clean shop towel and apply a small amount of black disc brake grease to the backing plate of each rear brake pad. NOTE Make sure disc brake grease is not applied to the lining of the rear brake pads. 4. Install the No. 1 Anti-squeal shims. Install the No. 2 Anti-squeal shims. Figure 3. 5. Using the Variable Pin Wrench (SST 09960-10010), slowly rotate the caliper piston until the piston groove is positioned as shown in the illustration below. 6. Install new rear brake anti-squeal shims with brake pads into the rear caliper assemblies brackets. Refer to (TIS), 2010 Prius Repair Manual: Brake – Brake (Rear) Brake: Rear Brake: Installation NOTE • When installing the rear disc brake caliper assembly on the rear disc brake caliper mounting bracket, ensure the protrusion on the brake pad is centered in the caliper piston groove. • It is important to ensure the protrusion is not contacting the outer edges of the caliper piston groove. (both sides) 7. Road test the vehicle to con?rm the condition has been reduced.

1997 Ford Explorer Cable and Conduit Parking Brake Rear Removal

0

Filed Under (Ford) by admin on 18-02-2011

download
1. NOTE: Make sure the parking brake control is fully released. Relieve the tension on the parking brake system. 1. Pull the front parking brake cable and conduit. 2. Insert a suitable retainer. 2. CAUTION: Do not use heat to loosen a seized lug nut (1012). Heat can damage the wheel and the wheel bearings. Remove the rear wheels and tires; loosen the lug nuts. 1. Remove the center cap. 2. With the weight of the vehicle on the wheels, loosen, but do not remove, the lug nuts. 3. WARNING: THE ELECTRICAL POWER TO THE AIR SUSPENSION SYSTEM MUST BE SHUT OFF PRIOR TO HOISTING, JACKING OR TOWING AN AIR SUSPENSION VEHICLE. THIS CAN BE ACCOMPLISHED BY TURNING OFF THE AIR SUSPENSION SWITCH LOCATED IN REAR JACK STORAGE AREA. FAILURE TO DO SO MAY RESULT IN UNEXPECTED INFLATION OR DEFLATION OF THE AIR SPRINGS WHICH MAY RESULT IN SHIFTING OF THE VEHICLE DURING THESE OPERATIONS. Raise and support the vehicle; refer to Section 100-02 . 4. Remove the tire and wheel assembly. 1. Remove the lug nuts. 2. Remove the tire and wheel assembly. 5. Disconnect the (A) parking brake intermediate cable from the (B) parking brake rear cable and conduit, LH. 6. Separate the (A) RH parking brake rear cable and conduit from the (B) LH parking brake rear cable and conduit at the (C) parking brake cable equalizer. 7. Remove the RH parking brake rear cable and conduit from the parking brake cable bracket (2530). 1. Compress the parking brake cable clip. 2. Remove the RH parking brake rear cable and conduit from the parking brake cable bracket. 8. Remove the RH parking brake rear cable and conduit to LH parking brake rear cable and conduit clip. 9. Remove the (A) RH parking brake rear cable and conduit from the (B) rear parking brake cable retainer (2A709). 10. Remove the RH parking brake rear cable and conduit to the RH hydraulic brake line clip. 11. Remove the parking brake cable retainer clip (2A826). 1. Remove the parking brake cable retainer clip bolt. 2. Remove the parking brake cable retainer clip. 12. Unclip the parking brake rear cable and conduit from the brake line clip on top of the rear axle housing.

2000 Ford F-150 Parking Brake Rear Drum Brakes

0

Filed Under (Ford) by admin on 02-02-2011

download
Remote release handle Parking brake control Parking brake rear cable and conduit clip (part of 2A635) Parking brake cable bracket Parking brake rear cable and conduit— (LH) Parking brake rear cable and conduit— (RH) Parking brake cable equalizer Front parking brake cable and conduit Front parking brake cable clip The parking brake system is actuated when the parking brake control (2780) is depressed. The parking brake control applies tension to the front parking brake cable and conduit (2853) and parking brake cable equalizer (2A602). The parking brake cable equalizer is coupled to the RH parking brake rear cable and conduit (2A635) and the LH parking brake rear cable and conduit. The respective rear brake assemblies are then applied. The rear wheel brake assembly contains a cable-actuated parking brake assembly. The parking brake releases the rear brakes using a remote release lever incorporated with the parking brake control. If the parking brake control is not fully released, the parking brake signal switch will illuminate the brake warning light. The parking brake signal switch is mounted on the parking brake control. The switch is held in place by a self-tapping screw and aligned with a locater pin. The drum brake parking brake system is self-adjusting, therefore cable tension does not need to be adjusted. Rear Disc Brakes Parking Brake Components, Rear Disc Brakes

2003 Ford Mustang Brake System Bleeding

0

Filed Under (Ford) by admin on 08-03-2011

download
Master Cylinder Priming — In-Vehicle or Bench WARNING: Carefully read cautionary information on product label. For EMERGENCY MEDICAL INFORMATION seek medical advice. In the USA or Canada on Ford/Motorcraft products call: 1-800-959-3673. For additional information, consult the product Material Safety Data Sheet (MSDS) if available. Failure to follow these instructions may result in personal injury. CAUTION: Do not allow the brake master cylinder reservoir to run dry during the bleeding operation. Keep the brake master cylinder reservoir filled with the specified brake fluid. Never reuse the brake fluid that has been drained from the hydraulic system. CAUTION: Brake fluid is harmful to painted and plastic surfaces. If brake fluid is spilled onto a painted or plastic surface, immediately wash it with water. NOTE: When any part of the hydraulic system has been disconnected for repair or installation of new components, air can enter the system and cause spongy brake pedal (2455) action. This requires bleeding of the hydraulic system after it has been correctly connected. The hydraulic system can be bled manually or with pressure bleeding equipment. NOTE: When a new brake master cylinder (2140) has been installed or the system has been emptied, or partially emptied, it should be primed to prevent air from entering the system. 1. For in-vehicle priming, disconnect the brake lines. 2. For bench priming, mount the brake master cylinder (2140) in a vise. 3. Install short brake tubes with the ends submerged in the brake master cylinder reservoir (2K478), and fill the brake master cylinder reservoir with High Performance DOT 3 Brake Fluid C6AZ-19542-AB or equivalent DOT 3 fluid meeting Ford specification ESA-M6C25-A. 4. Have an assistant pump the brake pedal (2455), or slowly depress the primary piston until clear fluid flows from both brake tubes, without air bubbles. 5. If the brake master cylinder has been primed at the bench, install it in the vehicle. For additional information, refer to Section 206-06. 6. Remove the short brake tubes, and install the brake outlet tubes. 7. Bleed each brake tube at the brake master cylinder as follows: 1. Have an assistant pump the brake pedal, and then hold firm pressure on the brake pedal. 2. Loosen the rear most brake tube fittings until a stream of brake fluid comes out. While the assistant maintains pressure on the brake pedal, tighten the brake tube fitting. 3. Repeat this operation until clear, bubble-free fluid comes out. 4. Refill the brake master cylinder reservoir as necessary. Repeat the bleeding operation at the front brake tube. Master Cylinder Priming — 4.6L 1. CAUTION: Use only bleed screws on the engine side of the brake master cylinder (2140). The hydro-boost bleed screw, located near the dash on the hydro-booster casting, is for the booster cavity filled with power steering fluid, not brake fluid. Connect a clear waste line to the bleed screw closet to the booster first and the other end in a container partially filled with recommended brake fluid.

2008 Ford Expedition Brake Pads REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 04-03-2011

download
WARNING: Do not use any fluid other than clean brake fluid meeting manufacturer’s specification. Additionally, do not use brake fluid that has been previously drained. Following these instructions will help prevent system contamination, brake component damage and the risk of serious personal injury. WARNING: Carefully read cautionary information on product label. For EMERGENCY MEDICAL INFORMATION seek medical advice. In the USA or Canada on Ford/Motorcraft products call: 1-800-959-3673. For additional information, consult the product Material Safety Data Sheet (MSDS) if available. Failure to follow these instructions may result in serious personal injury. WARNING: Always install new brake shoes or pads at both ends of an axle to reduce the possibility of brakes pulling vehicle to one side. Failure to follow this instruction may result in uneven braking and serious personal injury. NOTICE: Do not spill brake fluid onto painted or plastic surfaces or damage to surface may occur. If brake fluid is spilled onto a painted or plastic surface, immediately wash the surface with water. 1. Check the brake fluid level in the brake master cylinder reservoir. If required, remove the fluid until the brake master cylinder reservoir is half full. 2. Remove the wheel and tire. For additional information, refer to Section 204-04. 3. NOTICE: Do not allow the brake caliper to hang by the flexible brake hose or damage to the hose may occur. Remove the 2 brake caliper guide pin caps and bolts and position the caliper and brake pad assembly aside. Support the caliper using mechanic’s wire. Remove and discard the guide pin bushings. Inspect the guide pin threads for damage, install new guide pin(s) as necessary. 4. Remove the brake pads from the caliper. 5. Inspect the brake pads for wear or contamination and install new pads as necessary. For additional information, refer to General Procedures in Section 206-00. 6. Using a C-clamp and a worn brake pad, press the piston into the caliper. 7. Inspect the brake disc and resurface or install a new brake disc as necessary. For additional information, refer to General Procedures in Section 206-00. Installation 1. Clean, dry and inspect the brake caliper anchor plate. Apply equal amounts of the supplied yellow lubricant to the 4 brake pad contact points on the anchor plate as shown. 2. NOTICE: Do not apply lubricant to guide pin threads or incorrect tightening of the guide pins may result. Install new brake hardware as follows: Apply equal amounts of the supplied white lubricant to the inside of the guide pin bushings. Install the guide pin bushings into the caliper bores. Install the guide pins into the bushings. 3. Install the brake pads to the caliper. 4. Position the caliper onto the anchor plate and install the 2 brake caliper guide pin bolts. To install, tighten to 38 Nm (28 lb-ft). Clean and dry guide pin threads as necessary. 5. Fill the master cylinder with clean, specified brake fluid. 6. Install the wheel and tire. For additional information, refer to Section 204-04. 7. Apply the brake several times to verify correct brake operation.