97 laguna airbag light reset
You are searching repair manual in PDF format about 97 laguna airbag light reset use another keyword for search another post or files
97 laguna airbag light reset Direct Download speed 5787 Kb/s
97 laguna airbag light reset Full Version speed 6767 Kb/s
Filed Under (Renault) by admin on 26-01-2016
The reset button is located under the speedometer on the instrument cluster. Switch ignition on.
? Switch ignition on. ? Press reset button until “spanner” symbol flashes. ? Keep button depressed until “spanner” symbol stops flashing and remains illuminated. ? Indicator shows appropriate service interval. ? Release reset button. ? Switch ignition off. Some Vehicles are fitted with a ‘SERV’ lamp, this is not a service interval indicator lamp. It is a malfunction indicator lamp (MIL)
Filed Under (Mazda) by admin on 01-03-2011
DESCRIPTION On some vehicles, when a power plug with improper fabrication (such as a phone charger) is inserted into either of the accessory sockets (center and/or rear), the airbag warning light may illuminate with DTC B1342, B2477 AND / OR C1946 stored in memory. Due to the improper power plug, the center or rear accessory socket fuse blows, and a short-circuit occurs in the SAS control module, causing the airbag warning light illumination with DTC B1342, B2477 AND / OR C1946 set. Despite the DTCs and airbag warning light being illumi- nated, the airbag system will continue to function. After verifying customer concern, perform the following repair procedures in order: • A – FUSE INSPECTION AND REPLACEMENT • B – SAS CONTROL MODULE CONFIGURATION AND REMOVAL / INSTALLATION (1) • C – PERFORM SSP78 A – FUSE INSPECTION AND REPLACEMENT 1. Visually inspect OUTLET CTR (15A) and OUTLET RR (15A) fuses located in the main fuse block in the engine compartment. Refer to MS3 online information or Workshop Manual WIRING DIAGRAMS. NOTE: – - In the wiring diagram these fuses are referred to as 19 and 20. In the owners manual these fuses are referred to as 17 and 18. 2. Replace any blown fuses with a new 15A fuse (9970-51-315). 3. Proceed to B – SAS CONTROL MODULE CONFIGURATION AND REMOVAL / INSTALLATION. B – SAS CONTROL MODULE CONFIGURATION AND REMOVAL / INSTALLATION
Filed Under (Audi) by admin on 30-03-2010
This Service & Airbag Reset Tool allows you to reset your car’s Airbag Fault Light
& Service (Oil Service & Inspection Service) Indicators on VW/Audi/Seat/Skoda
manufactured from 1994 to the latest one that using CAN-BUS protocol, please
read the Compatible Vehicles for detail models.
Filed Under (Rover) by admin on 23-05-2010
some models, no serial diagnostics are available with the airbag system. On these systems, faults are reported by means of the Airbag warning light on the dashboard. The Rover models concerned are as follows: • Metro • Rover 100 • New Rover 400 • Rover 600
ED3 Airbag For the ED3 system on Metro, Rover 100, and New Rover 400 vehicles, the airbag warning light has the following meaning.
Warning light behavior when Meaning ignition is switched on. Comes on then goes off after No fault in system 3 seconds. Comes on and stays on Fault in airbag module, SRS ECU, cabling, or airbag module connector Comes on, goes off after 3 Fault in airbag module, SRS seconds, then comes back on ECU, cabling, or airbag and remains on. module connector
Filed Under (Dodge) by admin on 18-01-2011
Driver Side 1. Disconnect and isolate the battery negative cable. If the airbag has not been deployed, wait two minutes for the system capacitor to discharge before further service. Driver Side Airbag Module Remove/Install 2. From the underside of the steering wheel, remove the two screws that secure the driver side airbag module to the steering wheel. 3. Pull the airbag module away from the steering wheel far enough to access the wire harness connectors on the back of the airbag module. 4. Unplug the airbag module and horn switch wire harness connectors from the back of the airbag module. 5. Remove the driver side airbag module from the steering wheel. 6. If the airbag has been deployed, the clockspring must be replaced. See Clockspring in the Replacement for the procedures. 7. When installing the airbag module, connect the clockspring wire harness connector to the module by pressing straight in on the connector. Be certain that the connector is fully engaged by observing the latch arms on each side of the connector. When these arms move outward from the connector, the connector is latched. 8. Connect the horn switch wire harness connectors. 9. Install the airbag module in the steering wheel. Tighten the mounting screws to 10.2 N.m (90 in. lbs.) . 10. Do not connect the battery negative cable at this time. See Airbag System in the Diagnosis and Testing for the proper procedures. Passenger Side The following procedure is for replacement of a faulty or damaged passenger side airbag module. If the passenger side airbag module has been deployed, the instrument panel assembly must be replaced. The instrument panel assembly includes a passenger side airbag and airbag door. Refer to Instrument Panel, Gauges and Warning Indicators/Instrument Panel/Instrument Panel Assembly Replacement. 1. Disconnect and isolate the battery negative cable. If the airbag has not been deployed, wait two minutes for the system capacitor to discharge before