AUTOMATIC GEARBOX SELECTOR SWITCH opel


You are searching repair manual in PDF format about AUTOMATIC GEARBOX SELECTOR SWITCH opel use another keyword for search another post or files



  AUTOMATIC GEARBOX SELECTOR SWITCH opel Direct Download speed 5787 Kb/s

  AUTOMATIC GEARBOX SELECTOR SWITCH opel Full Version speed 6767 Kb/s




2003 Ford Econoline E350 1 Ton Main Climate Control Switches REMOVAL

0

Filed Under (Ford) by admin on 31-07-2010

download
1. Disconnect the battery ground cable. 2. Remove the center trim panel. 3. Remove the control assembly. 1 Remove the screws. 2 Remove the control assembly. 4. Remove the A/C-heater function selector switch knob. 5. Disconnect the vacuum harness connector. 6. Disconnect the A/C-heater function selector switch connector. 7. Remove the A/C-heater function selector switch. 1 Remove the screw. 2 Remove the A/C-heater function selector switch. 8. Remove the temperature control switch knob. 9. Disconnect the temperature control switch connector. 10. Remove the temperature control switch. 1 Remove the screw. 2 Remove the temperature control switch. 11. Remove the heater blower motor switch knob. 12. Disconnect the heater blower motor switch connector. 13. Remove the heater blower motor switch. 1 Remove the screw. 2 Remove the heater blower motor switch. INSTALLATION 1. Follow the removal procedure in reverse order.

Related entry:

1990 e350 ignition switch diagram, auto or manual selector gas oven, econoline headlight knob removal, where does a trailer inertia switch plug into a e350,

2004 Honda Element EX ROCKER ARM OIL PRESSURE SWITCH (VTEC OIL PRESSURE SWITCH)

0

Filed Under (Honda) by admin on 21-12-2010

download
1. Check the engine oil level. Is the level OK? YES- Go to step 2 . NO- Adjust the engine oil to the proper level, then go to step 14 . 2. Turn the ignition switch ON (II). 3. Clear the DTC with the HDS. 4. Do the VTEC TEST in the INSPECTION MENU with the HDS. Is the result OK? YES- Intermittent failure, system is OK at this time. Check for poor connections or loose terminals at the rocker arm oil pressure switch (VTEC oil pressure switch) and the ECM/PCM. NO- Go to step 5 . 5. Check the result of step 4 . Rocker Arm Oil Pressure Switch (VTEC Oil Pressure Switch) Failure Rocker Arm Oil Pressure Switch (VTEC Oil Pressure Switch) Open Rocker Arm Oil Pressure Switch (VTEC Oil Pressure Switch) SIG Line Open Rocker Arm Oil Pressure Switch (VTEC Oil Pressure Switch) GND Line Open Is the test result any of the above? YES- Go to step 6 . NO- Check for poor connections or loose terminals at the rocker arm oil pressure switch (VTEC oil pressure switch). If it is OK, replace the rocker arm oil control solenoid (VTEC solenoid valve) (see step CMP SENSOR A REPLACEMENT ), then go to 14 . 6. Turn the ignition switch OFF. 7. Disconnect the rocker arm oil pressure switch (VTEC oil pressure switch) 2P connector. 8. Check for continuity between rocker arm oil pressure switch (VTEC oil pressure switch) 2P connector terminals No. 1 and No. 2.

Related entry:

2001 accord low pressure intake, peugeot 307 gearbox oil pressure regulation, where is the oil pressure relief valve situated on ford mondeo 2002, 72 monte carlo wiring diag, air solenoid valve on international 8600 not working properly, 2007 element rocker arm oil pressure switch, diagram of windshield wiper relays for1994 honda accord, 2001 mford taurus rocker arm torque, cs198 switch/commutateur interruptor location 1996 camaro, astra switch ignition remove,

1991 Ford F 150 Ignition Switch Service and Repair

0

Filed Under (Ford) by admin on 29-07-2010

download
Removal 1. Disconnect the battery ground cable. 2. Remove steering column shroud and lower the steering column. Refer to Steering Column: Service and Repair: Removal/Installation . 3. Disconnect the switch wiring at the multiple plug. 4. Remove the two nuts that retain the switch to the steering column. 5. LIFT the switch VERTICALLY UPWARD to disengage the actuator rod from the switch and remove switch. Installation 1. When installing the ignition switch, both the locking mechanism at the top of the column and the switch itself must be in LOCK position for correct adjustment. To hold the mechanical parts of the column in LOCK position, move the shift lever into PARK (with automatic transmissions) or REVERSE (with manual transmissions), turn the key to LOCK position, and remove the key. New replacement switches, when received, are already pinned in LOCK position by a metal shipping pin inserted in a locking hole on the side of the switch. 2. Engage the actuator rod in the switch. Must be inserted in the slot of the sliding, white carrier. 3. Position the switch on the column and install the retaining nuts, but do not tighten them. 4. Move the switch UP and DOWN along the column to locate the mid-position of rod lash. Tighten the two ignition switch retaining nuts (TOP NUT FIRST to minimize rod binding) to 4.51-7.34 N.m(40-65 in-lb) . 5. Remove the lockpin. Connect the battery cable, and check for proper start in PARK or NEUTRAL. Also, ensure the start circuit cannot be actuated in the DRIVE and REVERSE position and that the engine will shut off in either DRIVE, REVERSE or NEUTRAL. If the engine will not shut off in the above positions then the switch is NOT adjusted properly. The switch will have to be re-adjusted. Refer to Ignition Switch: Adjustments . 6. Raise the steering column into position at instrument panel. Refer to Steering Column: Service and Repair: Removal/Installation . 7. Confirm that accessories are deactivated with ignition switch in OFF position, and that accessories are operable with switch in RUN position.

Related entry:

1940 ford ignition, 1970 c10 manual transmission back up switch, 1996 FORD TAURUS ACTUATOR, 1996 ford taurus ignition actuator rod, 2000 e250 only goes into drive, HOW TO HOOK TOGGLE SWITCH TO THE IGNITION 1990 ARROWSTAR, standard transmission reverse light,

2008–2009 Toyota Highlander Intermittent No Crank/No Start

0

Filed Under (Toyota) by admin on 20-05-2011

download
Some Highlander, Matrix, and RAV4 vehicles may intermittently exhibit a “no crank” condition. The engine can usually be started after moving the shift lever to the Neutral position or by cycling the shift lever in and out of the Park position. A revised neutral start switch assembly is available to address this condition. Repair Procedure 1. Replace the neutral start switch assembly. Refer to the Technical Information System (TIS), applicable model and model year Repair Manual: 2008 Highlander: • Drivetrain – Automatic Transmission/Transaxle – “U151E Automatic Transaxle: Park/Neutral Position Switch: Removal / Adjustment / Installation” • Drivetrain – Automatic Transmission/Transaxle – “U151F Automatic Transaxle: Park/Neutral Position Switch: Removal / Adjustment / Installation” 2009 Highlander: • Drivetrain – Automatic Transmission/Transaxle – “U151E Automatic Transaxle: Park/Neutral Position Switch: Removal / Adjustment / Installation” • Drivetrain – Automatic Transmission/Transaxle – “U151F Automatic Transaxle: Park/Neutral Position Switch: Removal / Adjustment / Installation” 2009 Matrix: • Drivetrain – Automatic Transmission/Transaxle – “U140F Automatic Transmission/Transaxle: Park/Neutral Position Switch: Removal / Adjustment / Installation” 2010 Matrix: • Drivetrain – Automatic Transmission/Transaxle – “U140F Automatic Transmission/Transaxle: Park/Neutral Position Switch: Removal / Adjustment / Installation”

Related entry:

automatic park neutral switch 2005 optra, U241E AUTOMATIC TRANSAXLE manual, 03 highlander ps pump replacement procedure, 2004 toyota highlander red mud guard, wheres the transmission fluid in a 2004 holden vectra automatic,

1996 Jeep Cherokee Neutral Safety Switch: Service and Repair Automatic

0

Filed Under (Jeep) by admin on 17-09-2010

download
REMOVAL 1. Raise vehicle. 2. Disconnect switch wire harness connector. 3. Pry washer lock tabs upward and remove switch attaching nut and tabbed washer. 4. Remove switch adjusting bolt. 5. Slide switch off manual valve shaft. INSTALLATION 1. Disconnect shift linkage rod from shift lever on left side of transmission. 2. Rotate manual shift lever all the way rearward. Then rotate lever forward two detent positions to Neutral. 3. Install switch on manual valve shaft and install switch adjusting bolt finger tight. Do not tighten bolt at this time. 4. Install tabbed washer on manual valve shaft and install switch attaching nut. Tighten nut to 6.9 Nm (61 inch lbs.) torque but do not bend washer lock tabs over nut at this time. 5. Verify that transmission is in Neutral. 6. Rotate switch to align neutral standard line with vertical groove on manual valve shaft. 7. Align switch standard line with groove or flat on manual valve shaft. 8. Tighten switch adjusting bolt to 13 Nm (108 inch lbs.) torque. 9. Bend at least two washer lock tabs over switch attaching nut to secure it. 10. Connect shift linkage rod to shift lever on left side of case. 11. Connect switch wires to harness and lower vehicle. 12. Check switch operation. Engine should start in Park and Neutral only.

Related entry:

mazda 6 neutral safety switch, 1988 f250 neutral safety switch removal, how to wire chevy p30 nuetral safety switch, how to change neutral safety switch in 2005 mazda3, 2008 mazda 3 netural switch location, installing a neutral safety switch 2007 mazda 6, replacing the safety neutral switch on a mazda 6, where is the pnp switch located on a 2001 impala 3 8 and floor shift, how to replace a neutral safety switch on a 2003 chevy impala, where is the neutral safety switch in 2005 mazda3,