CHANGE Ignition Coil FOR MERCURY MONTEREY 2004


You are searching repair manual in PDF format about CHANGE Ignition Coil FOR MERCURY MONTEREY 2004 use another keyword for search another post or files



  CHANGE Ignition Coil FOR MERCURY MONTEREY 2004 Direct Download speed 5787 Kb/s

  CHANGE Ignition Coil FOR MERCURY MONTEREY 2004 Full Version speed 6767 Kb/s




1993 Honda Civic del Sol S IGNITION CHECKS ELECTRONIC IGNITION SYSTEM

0

Filed Under (Honda) by admin on 03-01-2011

download
Spark Check for spark at secondary coil wire and each spark plug wire using a spark tester. If spark is not present, continue with following tests. Check spark plug wire resistance on suspect wires. Resistance should be less than 25,000 ohms. Ignition Coil Power Source 1. On Civic, remove distributor cap to check power source directly at coil. On all models, disconnect ignition coil primary leads. Turn ignition on. Using voltmeter, check voltage between ground and Black/Yellow wire terminal of ignition coil harness. 2. Battery voltage should be present. If battery voltage is not present, check for open in Black/Yellow wire between coil and ignition switch. Ignitor Power Source Turn ignition off. Disconnect harness connector at distributor. Turn ignition on. Using voltmeter, check for battery voltage between ground and Black/Yellow wire of harness. If voltage is not present, check for open in Black/Yellow wire between ignition coil and harness connector. If wire is okay, check ignition coil resistance (for internal short to ground). Ignitor Check Check TDC/CRANK/CYL sensor resistance values. See TACH PULSE SIGNAL . Check power sources. If no problems are found and spark is not present, replace ignitor. Ignition Coil Resistance (Accord & Prelude) 1. Remove primary and secondary leads from ignition coil. Using an ohmmeter, check resistance between primary terminals “A” and “C” (“A” and “B” for Prelude) of ignition coil. See Fig. 2 . Resistance should be .6-.8 ohm at room temperature. 2. On Accord, check resistance between terminals “B” and “D” of ignition coil (tachometer circuit). Resistance should be about 2090-2310 ohms at room temperature. 3. On all models, check secondary resistance between terminal “A” and secondary output terminal (coil tower). See IGNITION COIL RESISTANCE table. Check for continuity between terminals “A” and “B” (“A” and “C” for Prelude). Continuity should exist. If readings are not within specification, replace coil.

Related entry:

72 monte carlo ignition switch wires color code, ga16de ignition wiring, 2000 ford e350 will not crank, 2000 pontiac montana wiring ignition coil schematics, ignition coil connector diagram on 2001 pontiac boneville, ignition coil pack for ford freestar 2005, 2003 jeep liberty 3 7 6cyl in cap coils how to check what is the ohms reading should be, 2003 s10 ignition removal, 2004 cadillac cts 3 6 ignition coil ohm spec, 2004 ford ranger 3 0 coil terminals andspark plug wire connection points,

1999 Subaru Forester Ignition Coil and High Tension Cables Inspection

0

Filed Under (Subaru) by admin on 06-10-2010

download
rePaIr Procedure/InformatIon Step 1) Ignition Coil Inspection Check the tower portion of the ignition coil for carbon tracks (leakage). If leakage is more than 5mm long, the ignition coil and high tension cables should be replaced (see Figure 1). Figure 1 Example of leakage on ignition coil tower. Step 2) High Tension Cable Inspection Check the high tension cables for carbon tracks (leakage). If leakage is evident, the high ten- sion cables should be replaced and the ignition coil cleaned (see figure 2 and refer to Step 3). Figure 2 Leakage on cable. Step 3) Ignition Coil Cleaning Procedure (if carbon track is less than 5mm) • • • • note: Do not insert the high tension cables until the ignition coil is dry. If there is any evidence of carbon, clean the surface of the ignition coil using a clean, soft rag dampened with water. Permit the ignition coil to dry. Clean the same area of the ignition coil using a clean soft rag dampened with Isopropyl alcohol. Permit the ignition coil to dry.

Related entry:

2003 s-10 evaporator coil cleanning, cleaning evaporator on 1995 chevy truck, cleaning the evaporator 96 chevy truck, evaparator coil cleaning 97 chevrolet truck,

2002 Nissan ALTIMA AND SENTRA MIL “ON” AND DTC P0340

0

Filed Under (Nissan) by admin on 16-01-2011

download
If an applied vehicle exhibits one or more of the following symptoms: • • • MIL “ON” with DTC P0340 (Camshaft Position Sensor) stored in Self Diagnosis results, Engine stumbles momentarily during cruise condition, Engine stops running at idle, The cause of this incident may be the ignition coils. A new resistor assembly (located inside the ignition coil tube) is available to repair the described symptoms, if they should occur. SERVICE PROCEDURE 1. Verify that the vehicle has one or more of the symptoms listed above in the Service Information. 2. Remove all four ignition coils. Refer to the appropriate 2002 Service Manual for removal procedure of the ignition coils (page EM-26 for Altima, page EM-106 for Sentra). 3. Install the new resistor assembly in all four ignition coil tubes as follows: A. Pull the rubber boot away from the ignition coil. Then, twist and pull the ignition coil tube from the ignition coil to separate them (see Figure 1). Rubber boot Tube Ignition coil Figure 1 TP010651 B. Remove the spring from the ignition coil tube and discard. Insert the new resistor assembly into the ignition coil tube exactly as shown in Figure 2 below. C. Assemble the ignition coil tube to the ignition coil. • Rotate the tube while pressing onto the coil. • A “pop” sound will be heard when the rubber boot is seated correctly to the ignition coil. • Ensure there are no gaps and bulges between the coil body and the rubber boot (see Figure 3).

Related entry:

1 and 15 term on coil mk2 jetta, 2002 nissan altima dos cheep coil packs cause problems, 2003 Nissan Altima how to manually unlock gas cap, ignition coil boot toyota corolla 2002, signs of a bad 2010 Mercedes CLS550 spark plugs coil packs, what are symtoms of failing ignition coil packs,

2001 Honda Accord EX IGNITION CHECKS

0

Filed Under (Honda) by admin on 23-04-2010

download
Ignition Coil Test (Accord 2.3L & CR-V) 1. Turn ignition off. Remove distributor cap, rotor and leak cover. Remove primary leads from ignition coil. Using an ohmmeter, check primary resistance between ignition coil terminals “A+” and “B-”. See Fig. 12 . Resistance should be as specified. See IGNITION COIL RESISTANCE table. 2. Check secondary resistance between ignition coil terminal “A+” and secondary output terminal (ignition coil tower). See IGNITION COIL RESISTANCE table. If readings are not as specified, replace ignition coil.Ignition Control Module (ICM) Input Test (Accord 2.3L) 1. Turn ignition off. Remove distributor cap, rotor and leak cover. Disconnect wires from ICM. See Fig. 14 or Fig. 15 . Turn ignition on. Check for voltage between body ground and ICM Black/Yellow wire. If battery voltage exists, go to next step. If battery voltage does not exist, check for open in Black/Yellow wire between ignition switch and ICM. See WIRING DIAGRAMS article.

Related entry:

2001 honda accord ignition switch replacement, remove icm 1998 honda accord,

2008-2009 GMC Canyon, GMC Envoy 2008-2009 Saab 9-7X Engine Runs Rough (Inspect for Water Intrusion in Spark Plug Recess Area, Replace Spark Plug and Ignition Coil, Seal Ignition Coil Bolt Hole Vents and Seal Hood Air Grille)

0

Filed Under (GM) by admin on 04-06-2010

download
Models: 2008-2009 Chevrolet Colorado, TrailBlazer 2008-2009 GMC Canyon, Envoy 2008-2009 HUMMER H3, H3T 2008-2009 Saab 9-7X All Equipped With Engine RPOs LLR, LLV, LL8 Please Refer to GMVIS Condition Some customers may comment that the malfunction indicator lamp (MIL) is illuminated. Some customers may also comment that the engine runs rough. The technician may find DTCs P0300, P0301, P0302, P0303, P0304, P0305, or P0306 set as current or in history, depending on which engine the vehicle is equipped with. Upon further examination, the technician may observe evidence of water intrusion into the spark plug recess area. Cause This condition may be caused by an engine being exposed to a large quantity of water, which may result in some of the water seeping down past the vented threads of an ignition coil bolt, then flowing through the vent opening that is located in the bottom of the related ignition coil bolt hole, and collecting in the spark plug recess area. Correction Important: DO NOT reprogram or replace the engine control module (ECM) for this condition. If evidence of water intrusion in the spark plug recess area/s is not observed, then refer to the appropriate DTC procedures in SI.

Related entry:

how to replace ac ac actuator on 2002 envoy, location of the evaporater drain on a 08 gmc acadia, how o install head lights on a 2008 GMC ACADIA, were is the ac receiver dryer on 2010 acadia, thermostat in where is the battery on a 2008 gmc acadia, 2008 gmc acadia free repair manual, service manual pdf for 04 gmc envoy xuv, 2008 gmc acadia thermostat, scematatics on midgate release button on 2004 gmc envoy xuv, replacing coil pack on 2009 gmc acadia,