CODE P0175 ON 04 NISSAN ALTIMA


You are searching repair manual in PDF format about CODE P0175 ON 04 NISSAN ALTIMA use another keyword for search another post or files



  CODE P0175 ON 04 NISSAN ALTIMA Direct Download speed 5787 Kb/s

  CODE P0175 ON 04 NISSAN ALTIMA Full Version speed 6767 Kb/s




2003 – 2005 Nissan Altima 2004 Nissan Maxima ENGINE IS HARD TO START WHEN WARM

0

Filed Under (Nissan) by admin on 04-06-2010

download
The engine is hard to start when warm, but starts OK when the engine is cold. NOTE: “Hard start” is engine crank time that is longer then 3 seconds. • If you only have DTC P0340, replace only Bank 1 CMP (Camshaft Position) Sensor. • If you only have DTC P0345, replace only Bank 2 CMP (Camshaft Position) Sensor. • If you have both codes, replace both sensors. • For a “hard to start warm” incident, replace both sensors, even if you have no codes. Refer to sections EC and EM in the correct Service Manual for sensor replacement information. If replacement of the sensors does not solve your incident, go back to ASIST for further diagnostic and repair information.

Related entry:

2 5 Nissan Engine cam removal, 2003 NISSAN MAXIMA AIR BAG CODE B1035, how to install an immobilizer on a 2004 NISSAN maxima, how to replace ac compressor pulley 2005 nissan altima, 04 nissan maxima hard start when hot, LOCATION OF THE ECM ON A 2004 NISSAN MAXIMA, location of tmc in 98 altima, remove headlight assembly from 2007 nissan altima, removing 2000 nissan pathfinder ecm, change headlight on 2001 nissan altima,

2005 – 2009 Nissan FRONTIER, Nissan XTERRA, Nissan PATHFINDER, FRONT AIR BAG CRASH ZONE SENSOR

0

Filed Under (Nissan) by admin on 04-01-2011

download
SERVICE PROCEDURE 1. Set the parking brake. 2. Connect C-III to the vehicle. 3. Use C-III to check for Air Bag DTCs. a. Navigate C-III to Air Bag Direct Diagnostic Mode. b. Make sure to check both SELF DIAG RESULTS and SELF-DIAG [PAST]. • SELF-DIAG [PAST] is under Special function. • If there are any DTCs stored for AIR BAG other than B1033, B1034 and/or B1035, perform repairs as needed, and then erase DTC before continuing with this procedure. • Diagnosis and repair for DTCs other than B1033, B1034, and/or B1035 is not covered by this bulletin. NOTE: All DTCs (except B1033, B1034, and B1035) must be repaired and erased before continuing with this procedure. 4. Disconnect C-III from the vehicle. 5. Start the engine and let it idle for about 5 seconds. 6. Turn the ignition OFF. 7. WARNING: Prep the vehicle for Crash Zone Sensor replacement as follows: The following are VERY IMPORTANT to prevent unexpected air bag deployment. • Remove the ignition key / Intelligent Key from the cabin of the vehicle and set aside, away from the vehicle (this will prevent accidentally turning the ignition ON). • Make sure the ignition remains OFF until after the new sensor is completely installed. • Make sure no one is in the vehicle cabin and no one enters the vehicle cabin until after the sensor is completely installed. • Wait for all control units to “power down” (at least 1 minute) before continuing. 8. Locate the Crash Zone Sensor (see Figure 2). Crash Zone Sensor Cover 9. Remove the 2 Crash Zone Sensor nuts shown in Figure 3. • Discard these nuts. They will not be reused. 10. Remove the Crash Zone Sensor Cover. 11. Disconnect the electrical connector shown in Figure 4.

Related entry:

diagram of nissan HB12 carburetor control unit, 2001 Nissan pathfinder will not idle after replacing battery, nissan serena c25 service manual, urvan nissan engine display repair, Manual Nissan Cabstar, isuzu ud front brakes repair guide, procedure for changing nissan wingroad ECU, abay e25 nissan full gasket set, AIRBAG LIGHT IS BLINKING ON NISAN TIIDA WHAT IS WRONG, AIRBAG LIGHT ON NISSAN TIIDA IS BLINKING WHAT IS WRONG,

1995 Ford Thunderbird Antilock Brakes / Traction Control Systems: Testing and Inspection Displaying and Reading Trouble Codes

0

Filed Under (Ford) by admin on 14-08-2010

download
NOTE: Ford DOES NOT provide procedures to retrieve or clear trouble codes without the Super Star II tester. The anti-lock brake/traction assist system has on-board diagnostic capabilities. However, the module as received from manufacturing is equipped with a stored error code (61). This will affect the service procedure. The error codes can be retrieved from the ABS module in the following manner. 1. 2. 3. 4. Connect Super STAR II tester to connector located in engine compartment on the power distribution box. Turn on Super STAR II tester and latch button down in TEST position. Turn ignition switch to RUN position. Read first code output. After approximately 15 seconds, the next code will be output. Leave button latched until all codes are output. NOTE: Make sure that all codes are written down. 5. The diagnostic procedure should be as follows provided that the CHECK ANTI-LOCK BRAKE indicator stays on all the time or flashes intermittently. NOTE: If the BRAKE warning indicator is on or intermittently comes on, refer to the Warning Indicator Symptom Chart. NOTE: If there are more codes stored in the anti-lock brake control module memory, no codes will erase until all codes have been output by the Super STAR II tester, all malfunctions have been serviced and the vehicle is driven about 40 km/h (25 mph). This means that if a 20s code originally existed and was serviced, it can be ignored when running the on-board diagnostic the second time. If the first code received is 18, 19 or in the 20s and no other code is received, service the indicated component. No other codes can be output if a 20s code exists. After servicing the indicated 18, 19, or 20s code, repeat the procedure for retrieving error codes. 6. If a code 61 is received with any other code, ignore the code 61 and service the other indicated components. If, after correcting all other indicated malfunctions, the CHECK ANTI-LOCK BRAKE indicator is still on, service the Fluid Level Switch (FLS) circuit. 7. If a code 61 is received and no other codes are received, service the FLS circuit. 8. If no code, or only a code 10 is received, use the Anti-Lock Quick Check Sheet since some possibilities are not recognized and retained in the anti-lock brake control module memory. See: Trouble Code Descriptions/Quick Check Sheet 9. When dealing with intermittent ABS warning light ON concern, make certain to visually inspect all wiring related to the component associated with the code received.

Related entry:

International Trouble Code Chart, International Trouble Code 2023 14P, ford code p2073, Navistar Fault Code List, Code P0645 Repair, 98 jeep grand cherokee engine code 320, cadillac seville climate control diagnostic procedure, list of codes for 2003 jeep liberty, 2005 International Trouble Code Chart, engine code 3984,

2002-2004 Nissan Altima W/QR25 ENGINE; NO-START AFTER ‘COLD SOAK’

0

Filed Under (Nissan) by admin on 29-11-2010

download
IF YOU CONFIRM • After a ‘cold soak’,* the engine cranks (turns with starter), but does not start. *Cold soak: Engine has cooled down to ambient (outside) temperature, regardless of summer or winter seasonal variations. • The engine may start if it is cranked for an extended period (more than 5 seconds) or if the throttle is opened during cranking. • After starting and operating for a few minutes the engine runs normally. ACTIONS • Replace the starter motor. • Add 1 can of Nissan Fuel System Cleaner into the fuel tank. • Perform ECM Part Number Check to see if the vehicle you are working on needs ECM Reprogramming. • Perform ECM Reprogramming, if needed. SERVICE PROCEDURE Replace Starter, Add Cleaner 1. Replace the starter motor. • Use the part number from the Parts Information section of this bulletin. • Refer to section SC, “STARTING SYSTEM, Removal and Installation” in the applicable Nissan Electronic Service Manual (ESM). 2. Add one full can of Nissan In-Tank Fuel System Cleaner to the fuel. NOTE: If the fuel tank is less than ¾ full, instruct the customer to fill the tank as soon as it is convenient after the repair. Driving with the Cleaner installed and low fuel level will not harm the fuel system or engine, but will reduce the effectiveness of the cleaning process. 3. Continue to ECM Part Number Check (next page).

NISSAN PERIODIC MAINTENANCE SCHEDULE NISSAN MICRA

0

Filed Under (Nissan) by admin on 11-04-2010

download
ENGINE MAINTENANCE (Petrol Engine) Replace engine oil Replace engine oil filter Inspect drive belts Inspect cooling system
Page 1© NISSAN NISSAN PERIODI CMAINTENANCE SCHEDULE NISSAN MICRA 15,000 KM Inspect brake, clutch and automatic
trans-axle fluids Inspect manual trans-axle gear oil Inspect power steering fluid and lines Inspect brake, clutch and exhaust systems
Inspect steering gear and linkage, axle and suspension parts and front driveshafts Inspect wheel alignment (if necessary rotate
tyres and balance Inspect brake pads, rotors and other brake components Inspect brake linings, drums and other brake
components Inspect foot brake, parking brake and clutch Lubricate locks, hinges & hood latch Inspect seat belts, buckles, retractors,
anchors & adjuster Clean or replace ventilation filter Replace brake fluid (Severe conditions only)

Related entry:

replacing micra interior light, NISSAN MICRA 1 2 2007 SERVICE SCHEDULE, intelligent key for y11 wingroad 2004 make, nissan micra bcm repairs, replacing micra aerial, Torque Settings for micra k12 cylinder head bolts, WHAT TIP OF ENGINE OIL FOR 1500CC NISSAN WINGROAD Y12,