Diagram 1998 Mazda 626 V6 Timing mark


You are searching repair manual in PDF format about Diagram 1998 Mazda 626 V6 Timing mark use another keyword for search another post or files



  Diagram 1998 Mazda 626 V6 Timing mark Direct Download speed 5787 Kb/s

  Diagram 1998 Mazda 626 V6 Timing mark Full Version speed 6767 Kb/s




1994 Ford Aerostar/Ranger/Explorer Camshaft Timing ADJUSTMENTS

0

Filed Under (Ford) by admin on 08-03-2011

download
Checking Timing An access plug is provided in the cam drive belt cover so that camshaft timing can be checked without removal of the cover or any other parts. 1. Remove the access plug from the cam drive belt cover. 2. Rotate the crankshaft so that the No. 1 piston is rising on compression stroke. 3. Set the crankshaft to TDC by aligning the timing mark on the crank pulley with the TC mark on the belt cover. Always turn the engine in the direction of normal rotation (clockwise, as viewed from the front). Backward rotation may cause the timing belt to jump time, due to the arrangement of the belt tensioner. 4. Look through the access hole in the belt cover to make sure that the timing mark on the cam drive sprocket is lined up with the pointer on the inner belt cover. 5. Install the belt cover access plug. Adjusting Timing Belt SPECIAL SERVICE TOOL(S) REQUIRED Description Crankshaft Belt Tension Adjusting Tool T74P-6254-A 1. Remove the outer timing belt cover as outlined in this section. CAUTION: Attempting to adjust timing belt tension without loosening spring pivot bolt will break Crankshaft Belt Tension Adjusting Tool T74P-6254-A when relieving tension on the belt. 2. If belt timing or tension is incorrect, loosen timing belt spring pivot bolt. 3. Hold tensioner with Camshaft Belt Tension Adjusting Tool T74P-6254-A. 4. While holding tensioner, loosen adjusting bolt and gradually release spring tension. Loosening Timing Belt Tensioner, 2.3L Tool Number 8 — 5. Using adjusting tool, pry tensioner away from belt. While holding, tighten adjusting bolt. There should be no tension on belt. Camshaft Timing Belt, 2.3L I-4 Timing Mark on Camshaft Sprocket Remove the bolts holding the crankshaft position sensor in place and pull the sensor assembly free of the dowel pin. 7. Remove the crankshaft pulley , crankshaft pulley hub and timing belt guide. 8. Remove the drive belt and inspect it for wear or damage. If the belt is damaged, replace it. 9. Remove one spark plug from each cylinder. 10. If not done: a. Loosen tensioner adjusting bolt. b. Using Camshaft Belt Tension Adjusting Tool T74P-6254-A, pry tensioner clockwise against spring tension as far as possible. c. Tighten adjusting bolt to hold tensioner in released position. 11. Align crankshaft so number one piston is at TDC (top dead center) as indicated by timing mark. 12. Line up camshaft sprocket timing mark with inner timing belt cover timing mark and key is pointing down.

Related entry:

yhs-default, yhsm-imp1, 2008 ford edge timing belt or chain, 1g-fe timing, 2000 toyota camry2 2liter timing belt diagram, 2000 volvo s40 timing belt replacement, 4g33 timing marks, diagram for 2005 chevy optra timing belt replacement, how to find compresion stroke on number one on 2005 hyundai tuson, 4d32 injection timing,

2003 TOYOTA TACOMA TIMING BELT INSTALLATION REMOVAL

0

Filed Under (Toyota) by admin on 13-01-2011

download
NOTICE: Always turn the crankshaft clockwise. (c) Check that the timing marks of the camshaft timing pul- leys and No.3 timing belt cover are aligned. If not, turn the crankshaft pulley 1 revolution (360°). (d) Remove the crankshaft pulley bolt. IF REUSING TIMING BELT, CHECK INSTALLATION MARKS ON TIMING BELT Check that there are 3 installation marks and front mark on the timing belt. If the installation and front marks have disappeared, before re- moving the timing belt, place 3 new installation marks on the timing belt to match the timing marks of the timing pulleys, and place a new front mark on the timing belt. 18. 19. REMOVE TIMING BELT TENSIONER Alternately loosen the 2 bolts, and remove them, the belt ten- sioner and dust boot. 20. REMOVE TIMING BELT 21. (a) REMOVE RH CAMSHAFT TIMING PULLEY Using SST, loosen the pulley bolt. SST 09960–10010 (09962–01000, 09963–01000) Remove the bolt, knock pin and timing pulley. (b) 22. (a) REMOVE LH CAMSHAFT TIMING PULLEY Using SST, loosen the pulley bolt. SST 09960–10010 (09962–01000, 09963–01000) Remove the bolt, knock pin and timing pulley. (b) 23. REMOVE NO.2 IDLER PULLEY Remove the bolt and idler pulley. 24. REMOVE NO.1 IDLER PULLEY Using a 10 mm hexagon wrench, remove the pivot bolt, idler pulley and plate washer. 25. REMOVE CRANKSHAFT TIMING PULLEY Remove the timing pulley. HINT: If the pulley cannot be removed by hand, use SST and a service bolt to remove the timing pulley. SST 09950–50011 (09951–05010, 09952–05010, 09953–05020, 09954–05011)

Related entry:

yhs-fullyhosted_003, mazda protege 2002 eng 2 0 camshaft timing mark, how to set the timing on a 2004 chevy cav, 2004 Chrysler Pacifica can you still be at top dead center and cranky and still be off the compression stroke, how tight to tighten ac belt on kia sorento, timing marks on a toyota paseao, 96 tahoe distributor timing marks diagram, 1992 525i m502tb camshaft timing marks diagram, Timing nissan NA20 engine on YouTube, 05 hyundia elantra 2 0 timing marks,

1996 Mitsubishi Eclipse GS-T TIMING BELT & BALANCE SHAFT BELT Removal

0

Filed Under (Mitsubishi) by admin on 18-01-2011

download
1. Disconnect negative battery cable. Remove engine undercover. Place wooden block between jack and oil pan, and raise engine slightly. Remove engine mount assembly near timing belt cover. 2. Remove clamp for power steering return hose near timing belt cover. Remove all drive belts and tensioner pulley bracket. See Fig. 1 . Remove power steering and water pump pulleys. Rotate crankshaft clockwise so that No. 1 cylinder is at TDC of compression stroke. Remove crankshaft pulley. CAUTION: DO NOT rotate crankshaft counterclockwise. Ensure timing marks are aligned. If reusing timing belts, mark timing belts for direction of rotation. 3. Remove upper timing belt cover and gasket. Remove stub bolt of engine support bracket, and remove center timing belt cover. Remove lower timing belt cover. NOTE: Camshaft sprocket dowel pins will be in 12 o’clock position when timing marks are correctly aligned. 4. Ensure camshaft, crankshaft and oil pump sprocket timing marks are aligned. See Fig. 2 or Fig. 3 . Loosen tensioner pulley center bolt. Move tensioner to relieve timing belt tension. Remove timing belt. Remove timing belt auto tensioner. See Fig. 1 . 5. Remove plug from left side of cylinder block. Install a .31″ (8.0 mm) diameter Phillips screwdriver into the hole against balance shaft. See Fig. 4 . Screwdriver must go in at least 2.36″ (60 mm) or more. If screwdriver will only go in about .79-.98″ (20-25 mm) before striking balance shaft, turn sprocket one revolution and align timing mark. Keep screwdriver in place until timing belt is installed. This ensures balance shaft driven by oil pump sprocket remains in correct position. 6. To remove timing belt “B” (balance shaft belt), hold crankshaft sprocket stationary with a spanner wrench. Remove crankshaft sprocket bolt. Using gear puller, remove outer crankshaft sprocket. 7. Remove crankshaft sensing blade (if equipped). See Fig. 5 . Loosen timing belt “B” tensioner bolt. If reusing timing belt “B”, mark direction of belt rotation for reassembly reference. Remove timing belt “B”.

Related entry:

camshaft sprocket removal mitsubishi 4g64 1992 8v, 1992 sirius 4g64 timing belt replacement mighty max, Mitsubishi 1992 4G64 SOHC timing belt tensioner spring wrench, mitsubishi triton balance shaft belt timing, mitsubishi 4g64 main timing belt tensioner spring installation instrudtioins, mitsubishi 4d56 timing, who can balance toyota drive shaft 412-814 area, metcees clk 320 tan seat belt, jhow tighting tenshon timing 2004 endeavor 3 8 engine, how to replace timing belts 1992 mitsubishi sirius 4g64 8 valve video,

1998 Mazda 626 LX Air Flow Meter/ Sensor Using the NGS Tester

0

Filed Under (Mazda) by admin on 19-11-2010

download
1. Check the mass air flow sensor for damage and cracks. 2. Connect the New Generation Star tester to the data link connector. 3. Turn the ignition switch to ON. 4. Select the “PID/DATA MONITOR AND RECORD” function on the NGS tester display and press TRIGGER. 5. Select “MAF V” on the NGS tester display and press START. The NGS tester measures and show the voltage. 6. If not as specified, inspect the following. (1) Harness continuity Between PCM terminal 88 and mass air flow sensor terminal E Between PCM terminal 36 and mass air flow sensor terminal D Between PCM terminal 103 and mass air flow sensor terminal C Between main relay terminal E and mass air flow sensor terminal B (2) Terminal voltage Mass air flow sensor terminal B voltage: Battery positive voltage Mass air flow sensor terminal C voltage: Below 1.0 V 7. If the terminal voltage is correct and there is harness continuity, replace the mass air flow sensor.

Related entry:

99 escort emission, 1998 infinity q45 maf connection, 2002 camaro black positive terminal wire, diagram of a 1998 for escort se, lb7 symptom and cause chart, truble shooting air mass problems 1998 mazda b2500,

1994-2000 Mazda 626 with 4 cyl A/T Vehicles with the Ford CD4E automatic transmission

0

Filed Under (Mazda) by admin on 10-10-2010

download
1994-1997 Ford Probe, Mazda MX3 with 4 cyl. & A/T 1994-2000 Mazda 626 with 4 cyl. & A/T 1998-2000 Mazda 626 with 6 cyl. & A/T 1995-2000 Ford Contour/Mercury Mystique with 6 cyl. & A/T 1999-2001 Mercury Cougar with A/T SUBJECT Vehicles with the Ford CD4E automatic transmission. CONDITION The driver’s side front CV axle has a 6-½ inch male inboard stub that fits into the transmission’s side gear. On the stub next to the housing seal surface is a carrier support surface that fits into the final drive sun gear inside the transmission (see figure 1). This sprocket assembly is chain driven with the reverse/overdrive sprocket by the planetary gear sets (see figure 2). The final drive sprocket assembly rides on the axle stub carrier support surface using a pressed, center bored bushing. This bushing wears the carrier support surface causing damage to the axle and eventually the transmission. SOLUTION If the carrier support surface of the axle being replaced appears rough and worn, then several possible failures need to be checked before replacing the axle or premature failure of the axle or possible damage to the transmission could occur. If the transmission’s internal oiling solenoid that lubricates this bushing fails, then the 2nd and 3rd gearshifts will not function. Although the Aftermarket lists this bushing, no tool exists to replace it. Ford only offer the bushing in a complete sprocket assembly making its replacement a very costly repair. The most common contributor to premature wear of this bushing is the vehicle not being within proper alignment specs. Without a four-wheel alignment, even though the front wheels may be centered to the rack, the rear thrust is pushing the front wheels causing stress on the front CV joints. The thrust forces acting on the front wheels while driving changes ALL the alignment specs resulting in the front wheels being in a constant turning action. This will wear the side gears and transmission seals as well as stressing this bushing. Another possible sign that alignment is affecting these items is a worn or torn inboard boot. Do not forget that worn motor mounts will also affect alignment thrust forces.

Related entry:

timing marks 2000 mazda 626 2 5 engine, mazda b 4000 manual 1994 download, yhs-adk_sychp, ford lynx gsi review, 1994 Ford L9000 Manual, what direction should turn cam to line the timing mark in a v6 1997 mazda 626, 2000 ford escort error po340 p1383, 2000 ford explorer exploded exhaust diagram, 2000 ford focus dome light assy, 2000 madza millenia 2 5 camshaft timing marks diagram,