Draining and Filling Cooling System 2004 buick


You are searching repair manual in PDF format about Draining and Filling Cooling System 2004 buick use another keyword for search another post or files



  Draining and Filling Cooling System 2004 buick Direct Download speed 5787 Kb/s

  Draining and Filling Cooling System 2004 buick Full Version speed 6767 Kb/s




2002 Ford Escort Workshop Manual Cooling System Draining Filling and Bleeding

0

Filed Under (Ford) by admin on 07-01-2011

download
Draining 1. Bring the engine to normal operating temperature and turn the engine off. With the cooling system under pressure, inspect cooling system hoses and clamped hose connections for leaks, excessive deterioration or contact wear. Inspect radiator installation retention. Note any discrepancies and proceed. 2. WARNING: Never remove the pressure relief cap while the engine is operating or when the cooling system is hot. Failure to follow these instructions can result in damage to the cooling system or engine or personal injury. To avoid having scalding hot coolant or steam blow out of the degas bottle when removing the pressure relief cap, wait until the engine has cooled, then wrap a thick cloth around the pressure relief cap and turn it slowly. Step back while the pressure is released from the cooling system. When you are sure all the pressure has been released, (still with a cloth) turn and remove the pressure relief cap. CAUTION: The coolant must be recovered in a suitable, clean container for reuse. If the coolant is contaminated, it must be recycled or disposed of correctly and replaced. CAUTION: Some vehicle cooling systems are filled with Motorcraft Premium Engine Coolant VC-4-A (in Oregon VC-5, in Canada CXC-10) or equivalent meeting Ford specification ESE-M97B44-A (green color). Others are filled with Motorcraft Premium Gold Engine Coolant VC-7-A meeting Ford specification WSS-M97B51-A1 (yellow color). Always fill the cooling system with the same coolant that is present in the system. Do not mix coolant types. NOTE: Less than 80 percent of coolant capacity can be removed from the engine. Dirty, rusty or contaminated coolant requires replacement. Drain engine coolant as follows: Open radiator draincock to drain the coolant system. Disconnect radiator overflow hose from radiator filler neck connection. Remove radiator coolant recovery reservoir and empty the fluid. Flush radiator coolant recovery reservoir with clean water. Drain and reinstall radiator coolant recovery reservoir and radiator overflow hose and clamp to radiator filler neck. Correct, repair or install new components found to be inoperative in Step 1. Filling and Bleeding with RADKITPLUS 1. Using the special tool, install the RADKITPLUS and follow the RADKITPLUS manufacturer’s instructions to fill and bleed the cooling system. Filling and Bleeding without RADKITPLUS CAUTION: Engine coolant provides freeze protection, boil protection, cooling efficiency and corrosion protection to the engine and cooling components. In order to obtain these protections, the engine coolant must be maintained at the correct concentration and fluid level in the degas bottle. When adding engine coolant, use a 50/50 mixture of engine coolant and clean, drinkable water. To maintain the integrity of the coolant and the cooling system:

Related entry:

PT Cruiser Cooling System Diagram, 2002 cavalier cooling system diagram, diagrahm of radiator reservoir overflow tank on a 2005 chev aveo, 2001 vr6 jetta coolant system diagram, 2005 sedona cooling system bleed, mustang 20011 3 7L how remove and replace transmission coolant lines, system for cooling infiniti g35, 2001 Chevrolet Malibu cooling system fill procedure, 2002 chevy cavalier engine coolant diagram, 2005 aveo engine to reservoir hose picture,

2002 Lincoln LS Workshop Manual Cooling System Draining, Filling and Bleeding

0

Filed Under (Lincoln) by admin on 23-01-2011

download
Draining WARNING: Never remove the pressure relief cap while the engine is operating or when the cooling system is hot. Failure to follow these instructions can result in damage to the cooling system or engine or personal injury. To avoid having scalding hot coolant or steam blow out of the degas bottle when removing the pressure relief cap, wait until the engine has cooled, then wrap a thick cloth around the pressure relief cap and turn it slowly. Step back while the pressure is released from the cooling system. When you are sure all the pressure has been released, (still with a cloth) turn and remove the pressure relief cap. CAUTION: The coolant must be recovered in a suitable, clean container for reuse. If the coolant is contaminated it must be recycled or disposed of correctly. CAUTION: Care must be taken to ensure the accessory drive belt does not become contaminated with engine coolant. CAUTION: Some vehicle cooling systems are filled with Motorcraft Premium Engine Coolant VC-4-A (in Oregon VC-5, in Canada CXC-10) or equivalent meeting Ford specifications ESE-M97B44-A (green color). Others are filled with Motorcraft Premium Gold Engine Coolant VC-7-A or equivalent meeting Ford specification WSS-M97B51-A1 (yellow color). Always refill the cooling system with the same coolant that was drained from the system. Do not mix coolant types. 1. Release the pressure in the cooling system by slowly turning the pressure relief cap one half turn counterclockwise. When the pressure is released, remove the pressure relief cap. 2. NOTE: Less than 80% of coolant can be recovered with the engine in the vehicle. Dirty, rusty or contaminated coolant requires replacement. Place a suitable container below the radiator draincock. If equipped, disconnect the coolant return hose at the oil cooler. Close the radiator draincock when finished. Filling and Bleeding With RADKITPLUS 1. Using the special tool, install the RADKITPLUS and follow the RADKITPLUS manufacturer’s instructions to fill and bleed the cooling system. Filling and Bleeding Without RADKITPLUS CAUTION: Engine coolant provides freeze protection, boil protection, cooling efficiency and corrosion protection to the engine and cooling components. In order to obtain these protections, the engine coolant must be maintained at the correct concentration and fluid level in the degas bottle. When adding engine coolant, use a 50/50 mixture of engine coolant and clean, drinkable water. To maintain the integrity of the coolant and the cooling system:

2003 Buick Rendezvous Draining and Filling Cooling System

0

Filed Under (Buick) by admin on 14-11-2010

download
Draining Procedure Important: Do NOT add any engine coolant supplement sealant pellets to the cooling system. Drain and refill the engine cooling system every 5 years or 240 000 km, (150,000 ml) , whichever occurs first. 1. Park the vehicle on a level surface. 2. Remove and clean the coolant recovery reservoir. Caution: To avoid being burned, do not remove the radiator cap or surge tank cap while the engine is hot. The cooling system will release scalding fluid and steam under pressure if radiator cap or surge tank cap its removed while the engine and radiator are still hot. 3. Remove the radiator cap when the engine is cool: 3.1. Slowly rotate the cap counterclockwise to the detention tab. Do not press down while rotating pressure cap. 3.2. Wait until any residual pressure, indicated by a hissing sound, is relieved. 3.3. After all hissing stops, press down on the radiator cap and rotate the cap counterclockwise in order to remove the cap. Important: Recover and store used coolant in a used coolant holding tank and submit the used coolant for recycling on a regular basis. Do NOT pour used coolant down the drain. Ethylene glycol antifreeze is very toxic. Disposing of ethylene glycol into the sewer system or ground water is both illegal and ecologically unsound. 4. Place a drain pan under the radiator drain cock in order to collect all of the used coolant. 5. Open the radiator drain cock. If only partial cooling system draining is required, drain enough coolant to perform the procedure.

2006 Ford Five Hundred Cooling System Draining, Filling and Bleeding

0

Filed Under (Ford) by admin on 05-07-2010

download
CAUTION: The coolant must be recovered in a suitable, clean container for reuse. If the coolant is contaminated it must be recycled or disposed of correctly. CAUTION: All vehicle cooling systems are filled with Motorcraft Premium Gold Engine Coolant VC-7-A or equivalent meeting Ford specification WSS-M97B51-A1 (yellow color). Always fill the cooling system with the same type of coolant that is present in the system. Do not mix coolant types. NOTE: The addition of Cooling System Stop Leak Pellets, VC-6, darkens Motorcraft Premium Gold Engine Coolant from yellow to golden tan. NOTE: Less than 80% of coolant capacity can be recovered with the engine in the vehicle. Dirty, rusty or contaminated coolant requires replacement.

1997 Mercury Villager Cooling System, Draining, Filling and Bleeding

0

Filed Under (Mercury) by admin on 08-03-2011

download
WARNING: THE ELECTRIC COOLING FAN MAY COME ON AT ANY TIME WHEN THE IGNITION SWITCH IS IN THE ON POSITION. If the coolant has not been changed in the last 36 months, or 48,000 km (30,000 miles), or if the inspection reveals hoses, gaskets, or other components requiring service or replacement, the coolant must be drained and discharged, or saved for reuse, depending on its condition. For a vehicle with a rear heater, set the rear blower switch to 4 and the rear temperature control knob to the full WARM position. 1. For vehicles equipped with manual A/C-heater, turn the ignition switch to the ON position and set the front temperature control panel selectors in the following positions: The front blower switch to 4. The front temperature control knob to the full WARM position. The rear control switch to the 4 position. The mode selector switches to any mode except OFF. 2. For vehicles equipped with electronic automatic temperature control (EATC), turn the ignition switch to the ON position and perform the following procedures: Turn the blower motor control to HI. Press the TEMP button to the maximum temperature setting. Turn the rear control switch to the 4 position. Turn the mode selector switches to any mode except OFF. 3. Turn the ignition switch (11572) OFF. 4. Remove the RH engine and transmission splash shield (6776). 5. NOTE: Do not use a galvanized drain pan if the coolant is going to be reused. Position a drain pan under the radiator (8005). 6. Open the radiator draincock (8115) at the bottom of the radiator inlet tank (8079). 7. CAUTION: Do not allow coolant to contact the drive belts (8620) or they will be damaged. Remove the radiator cap (8100) from the filler neck. If the system is hot and pressurized, carefully release the pressure before fully opening the radiator cap. 8. Use an Allen wrench to loosen the radiator air relief plug three turns. Do not remove the radiator air relief plug.