Auto Repair Manual Free Download and ReviewsFree download ebook pdf files automotive manual

download
WARNING: Carefully read cautionary information on product label. For EMERGENCY MEDICAL INFORMATION seek medical advice. In the USA or Canada on Ford/Motorcraft products call: 1-800-959-3673. For additional information, consult the product Material Safety Data Sheet (MSDS) if available. Failure to follow these instructions may result in personal injury. CAUTION: Do not spill brake fluid onto painted or plastic surfaces. If spilled, wipe up immediately before damage to the plastic or painted surfaces occurs. 1. Remove the wheel and tire assembly. For additional information, refer to Section 204-00. 2. Remove the parts in the order indicated in the following illustration and table. To remove individual parts, only carry out the listed steps: 3. To install, reverse the removal procedure. 4. If the hydraulic system was opened, bleed the brake system. For additional information, refer to Brake System Bleeding in this section. Item 2: Brake Caliper Removal Note 1. CAUTION: Do not allow the brake caliper to hang by the flexible brake hose. Support the caliper to the vehicle. Item 11: Brake Disc Removal Note 1. If removing the brake disc, only remove the caliper bracket bolts and position the caliper and bracket aside. Item 10: Spindle Nut Installation Note 1. Tighten the spindle nut to the specified torque. Rotate the hub counter-clockwise 5 rotations and then recheck the torque. Item 3: Brake Disc Pads Installation Note 1. CAUTION: Install a new lining if worn to or past the specified thickness above the metal backing plate or if the pad is damaged. Install new pads in complete axle sets. If replacing the brake pads, use a suitable suction device, remove the brake fluid in the master cylinder reservoir until it is half filled. 2. If replacing the brake pads, use a suitable tool to push the brake caliper pistons into the caliper bore. 3. One brake disc pad kit contains the pads required for both the RH and LH side. Item 1: Caliper Bolt Installation Note 1. Tighten the bottom caliper bolt and then the top caliper bolt. Item 11: Brake Disc Inspection Note 1. NOTE: If machining is necessary use a hub-mount brake lathe to machine the front brake disc. For additional information, refer to section Section 100-04. Measure the front brake disc, and resurface as necessary. Install a new front brake disc if beyond specification.

download
Master Cylinder Priming — In-Vehicle or Bench WARNING: Carefully read cautionary information on product label. For EMERGENCY MEDICAL INFORMATION seek medical advice. In the USA or Canada on Ford/Motorcraft products call: 1-800-959-3673. For additional information, consult the product Material Safety Data Sheet (MSDS) if available. Failure to follow these instructions may result in personal injury. CAUTION: Do not allow the brake master cylinder reservoir to run dry during the bleeding operation. Keep the brake master cylinder reservoir filled with the specified brake fluid. Never reuse the brake fluid that has been drained from the hydraulic system. CAUTION: Brake fluid is harmful to painted and plastic surfaces. If brake fluid is spilled onto a painted or plastic surface, immediately wash it with water. NOTE: When any part of the hydraulic system has been disconnected for repair or installation of new components, air can enter the system and cause spongy brake pedal (2455) action. This requires bleeding of the hydraulic system after it has been correctly connected. The hydraulic system can be bled manually or with pressure bleeding equipment. NOTE: When a new brake master cylinder (2140) has been installed or the system has been emptied, or partially emptied, it should be primed to prevent air from entering the system. 1. For in-vehicle priming, disconnect the brake lines. 2. For bench priming, mount the brake master cylinder (2140) in a vise. 3. Install short brake tubes with the ends submerged in the brake master cylinder reservoir (2K478), and fill the brake master cylinder reservoir with High Performance DOT 3 Brake Fluid C6AZ-19542-AB or equivalent DOT 3 fluid meeting Ford specification ESA-M6C25-A. 4. Have an assistant pump the brake pedal (2455), or slowly depress the primary piston until clear fluid flows from both brake tubes, without air bubbles. 5. If the brake master cylinder has been primed at the bench, install it in the vehicle. For additional information, refer to Section 206-06. 6. Remove the short brake tubes, and install the brake outlet tubes. 7. Bleed each brake tube at the brake master cylinder as follows: 1. Have an assistant pump the brake pedal, and then hold firm pressure on the brake pedal. 2. Loosen the rear most brake tube fittings until a stream of brake fluid comes out. While the assistant maintains pressure on the brake pedal, tighten the brake tube fitting. 3. Repeat this operation until clear, bubble-free fluid comes out. 4. Refill the brake master cylinder reservoir as necessary. Repeat the bleeding operation at the front brake tube. Master Cylinder Priming — 4.6L 1. CAUTION: Use only bleed screws on the engine side of the brake master cylinder (2140). The hydro-boost bleed screw, located near the dash on the hydro-booster casting, is for the booster cavity filled with power steering fluid, not brake fluid. Connect a clear waste line to the bleed screw closet to the booster first and the other end in a container partially filled with recommended brake fluid.

download
When a new brake master cylinder (2140) has been installed, or the brake system emptied or partially emptied, fluid may not flow from the bleeder screws during normal bleeding. It may be necessary to prime the system using the following procedure: 1. Use a tubing wrench to remove the brake lines from the master cylinder. 2. Install short brake lines in the brake master cylinder and position them so that they point back into the reservoir, and the ends of the pipes are submerged in brake fluid. 3. Fill the reservoir with new Ford High Performance DOT-3 Brake Fluid C6AZ-19542-AA or DOT-3 equivalent meeting Ford specification ESA-M6C25-A. 4. Cover the reservoir with a clean shop towel. 5. CAUTION: Brake fluid is harmful to painted and plastic surfaces. If brake fluid is spilled onto a painted or plastic surface, immediately wash it with water. Pump the brakes until clear, bubble-free fluid comes out of both brake lines. 6. Remove the short brake lines and reinstall the ones from the vehicle. 7. Bleed each brake line at the brake master cylinder using the following procedure: a. Have an assistant pump the brake pedal 10 times and then hold firm pressure on the pedal. b. Loosen the front brake line fitting with a tubing wrench until a stream of brake fluid comes out. Have your assistant maintain pressure on the brake pedal until the brake line fitting is tightened again. c. Repeat this operation until clear, bubble-free fluid comes out from around the tubing fitting. d. Repeat this bleeding operation at the rear brake line fitting. 8. If any of the brake lines or calipers have been removed, it may be helpful to prime the system by gravity bleeding it. This should be done after the brake master cylinder is primed and bled. To prime the brake system: a. Fill the brake master cylinder reservoir (2K478) with new Ford High Performance DOT-3 Brake Fluid C6AZ-19542-AA or equivalent meeting Ford specification ESA-M6C25-A. b. Loosen both rear caliper bleeder screws and leave them open until clear brake fluid flows out. Be sure to check the reservoir fluid level often and not let it run dry. c. Tighten the bleeder screws. d. One at a time, loosen the front caliper bleeder screws. Leave the bleeder screws open until

download
WARNING: Do not use any fluid other than clean brake fluid meeting manufacturer’s specification. Additionally, do not use brake fluid that has been previously drained. Following these instructions will help prevent system contamination, brake component damage and the risk of serious personal injury. WARNING: Carefully read cautionary information on product label. For EMERGENCY MEDICAL INFORMATION seek medical advice. In the USA or Canada on Ford/Motorcraft products call: 1-800-959-3673. For additional information, consult the product Material Safety Data Sheet (MSDS) if available. Failure to follow these instructions may result in serious personal injury. WARNING: Always install new brake shoes or pads at both ends of an axle to reduce the possibility of brakes pulling vehicle to one side. Failure to follow this instruction may result in uneven braking and serious personal injury. NOTICE: Do not spill brake fluid onto painted or plastic surfaces or damage to surface may occur. If brake fluid is spilled onto a painted or plastic surface, immediately wash the surface with water. 1. Check the brake fluid level in the brake master cylinder reservoir. If required, remove the fluid until the brake master cylinder reservoir is half full. 2. Remove the wheel and tire. For additional information, refer to Section 204-04. 3. NOTICE: Do not allow the brake caliper to hang by the flexible brake hose or damage to the hose may occur. Remove the 2 brake caliper guide pin caps and bolts and position the caliper and brake pad assembly aside. Support the caliper using mechanic’s wire. Remove and discard the guide pin bushings. Inspect the guide pin threads for damage, install new guide pin(s) as necessary. 4. Remove the brake pads from the caliper. 5. Inspect the brake pads for wear or contamination and install new pads as necessary. For additional information, refer to General Procedures in Section 206-00. 6. Using a C-clamp and a worn brake pad, press the piston into the caliper. 7. Inspect the brake disc and resurface or install a new brake disc as necessary. For additional information, refer to General Procedures in Section 206-00. Installation 1. Clean, dry and inspect the brake caliper anchor plate. Apply equal amounts of the supplied yellow lubricant to the 4 brake pad contact points on the anchor plate as shown. 2. NOTICE: Do not apply lubricant to guide pin threads or incorrect tightening of the guide pins may result. Install new brake hardware as follows: Apply equal amounts of the supplied white lubricant to the inside of the guide pin bushings. Install the guide pin bushings into the caliper bores. Install the guide pins into the bushings. 3. Install the brake pads to the caliper. 4. Position the caliper onto the anchor plate and install the 2 brake caliper guide pin bolts. To install, tighten to 38 Nm (28 lb-ft). Clean and dry guide pin threads as necessary. 5. Fill the master cylinder with clean, specified brake fluid. 6. Install the wheel and tire. For additional information, refer to Section 204-04. 7. Apply the brake several times to verify correct brake operation.

download
1. Remove the front disc brake caliper anchor plate. 2. On 4×4 vehicles, remove the brake disc. 3. On 4×2 vehicles, remove the brake disc and hub as follows: 1. 2. 3. 4. 5. 6. 7. Remove the hub grease cap. Remove the cotter pin. Remove the nut retainer. Remove the spindle nut. Remove the front wheel outer bearing retainer washer. Remove the outer front wheel bearing. Remove the brake disc and hub. 4. If necessary on 4×2 vehicles, remove the front wheel bearing. 1. Remove the wheel hub grease seal. 2. Remove the front wheel bearing. Installation 1. On 4×4 vehicles, position the brake disc to the wheel hub. Use Metal Brake Parts Cleaner F3AZ-19579-SA or equivalent to clean the brake disc and hub. On 4×2 vehicles, thoroughly clean and inspect the front wheel bearings and the brake disc and hub. Use Metal Brake Parts Cleaner F3AZ-19579-SA or equivalent. 3. On 4×2 vehicles, lubricate the front wheel bearings. Use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford specification ESA-M1C75-B.