GMC 5.7L intake leak


You are searching repair manual in PDF format about GMC 5.7L intake leak use another keyword for search another post or files



  GMC 5.7L intake leak Direct Download speed 5787 Kb/s

  GMC 5.7L intake leak Full Version speed 6767 Kb/s




1995-1997 Buick Riviera Engine Coolant Consumption or Coolant Leak (Inspect for Material Degradation/Replace Intake Manifolds)

0

Filed Under (Buick) by admin on 15-12-2010

download
Condition Some customers may comment on excessive engine coolant consumption, or an engine coolant leak near or under the throttle body area of the upper intake manifold. Cause Upper intake manifold composite material may degrade around the EGR stove pipe and could result in an internal or external coolant leak. Correction 1. Follow the upper intake manifold removal instructions found in the Engine Unit Repair Section of the Service Information Manual. 2. Refer to the arrow in the illustration of the upper intake manifold above. Inspect the inner diameter of the EGR passage for signs of material degradation. Degradation will appear as “pitting” of the composite material in the EGR port passage. 3. If degradation of upper intake manifold composite material is found, replace the lower and upper intake manifolds with the following part numbers: • Gasket Kit, Upper Intake Manifold — 89017554 • Manifold Kit, Upper Intake — 89017272 • Gasket, Lower Intake Manifold — 89017400 • Manifold, Lower Intake — 24508923 4. Follow the lower and upper intake manifold installation instructions found in the Engine Unit Repair Section of the appropriate Service Manual. 5. If degradation is not apparent, skip to Step 7. 6. Verify the repair. 7. If no degradation is found, evaluate the vehicle for other causes of excessive coolant consumption as noted in the Engine Diagnosis Section of the appropriate Service Manual.

Related entry:

97 buick riviera engine coolent refilling, upper metal water hose pipe with lip for 2003 bmw 325i, 2004 grand caravan coolant leak, 2007 doge caravan intake gasget leak, does it matter what antifreeze you use for a buick riveira 97,

2002-2005 Subaru Impreza WRX/STI Cold Air Intake Installation Guide

0

Filed Under (Subaru) by admin on 02-01-2011

download
Removal of Factory Intake 1. 2. Turn the ignition OFF and disconnect the vehicle’s negative battery cable. Loosen and remove the two bolts that secure the air inlet duct to the radiator core support, then remove the air inlet duct. Loosen the clamps at the air cleaner assembly and turbo inlet tube, then remove the stock intake tube. Loosen and remove the two bolts that secure the air cleaner assembly. Pull upwards to remove the air cleaner assembly. Using the bolt removed to secure the ABS control bracket. Loosen and remove the two screws that secure the mass air sensor to the air cleaner assembly, then remove the mass air sensor. Raise the vehicle and support with the jack stands, then remove the front passenger side tire. Remove the five plastic push/screw clips that secure the inner wheel house valance. Remove the 6 screw in push clips that secure the air duct to the lower valance, then remove the air duct. Remove the two remaining push clips that secure the lower valance, then pull the valance down. From inside the apron, remove the push clip that secures the apron to the upper fender. Remove the hex nut that secures the air intake resonator to the inner fender. Loosen and remove the second hex nut that secures the air intake resonator from underneath the vehicle. Remove the air intake resonator. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. Install of Intake 16. Install the reducer and clamps onto the turbo and secure. 17. Loosen and remove the hex bolt on the cam cover. 18. Using the provided allen bolts, secure the mass air sensor into the adapter on the intake tube. 19. Using the allen bolts, secure the mass air sensor into the adapter on the intake tube. 20. Slide the intake tube into the reducer and secure the mass air sensor into the adapter on the intake tube. 21. Tighten the clamp on the intake tube. 22. Install the reducer and clamps onto the intake tube. 23. From underneath the vehicle loosen and remove the hex nut that secures the ABS pump to the inner fender. 24. Slide the cold air tube intake tube from underneath the vehicle into the hole in the inner fender, then line up the bracket with the ABS bolts, and tighten with the nut remove. 25. Slide the reducer onto the cold air intake tube. 26. Install the Bomz Filtercharger onto the cold air intake tube and secure with clamp. 27. Reverse the removal process for the plastic wheelhouse valance and air duct with the stock push clips. 28. Reconnect the mass air sensor electrical connection. 29. Reconnect the negative battery cable and double check to make sure everything is tight before starting the vehicle. Resetting the ECU This is to be completed at your own risk. This procedure will reset the computer so that it may “learn” of your new intake. We are not to be held liable for any mishaps that you may occur while completing this process. • • Disconnect the Negative battery cable for 5 minutes. Reconnect the battery cable and false panel cover.

Related entry:

ac drain hose for 2010 mazda sx 9, 2001 COUGAR 2 5 LOWER INTAKE SOLENOID, 1997 gmc jimmy MAF relearn procedure, vwbeetle air vents removal procedure, diagram of where air flow sensor and throttle body is located on a toyota 2006 rav 4, torque pattern 3 8 chrysler upper lower intake, p0410 greska ople vektra b, northstar upper plenum, new vw beetle 2000 air vents, map sensor atpter for cold intake on 2004 subaru forester,

1997 Chevy K 1500 Intake Manifold Replacement (Upper)

0

Filed Under (Chevrolet) by admin on 19-09-2010

download
REMOVAL 1. Disconnect the battery negative cable assembly from the battery negative terminal. 2. Remove the air cleaner assembly. Refer to Powertrain Management. 3. Remove the wiring harness connectors and the brackets and move aside. 4. Remove the throttle cable and the bracket from the upper intake manifold. 5. Remove the cruise control cable, (if equipped). 6. Remove the fuel lines from the intake to the rear of the block. Refer to Powertrain Management. 7. Remove the ignition coil and the bracket. Refer to Starting and Charging 8. Remove the upper intake manifold. INSTALLATION 1. Install the upper intake manifold gasket. 2. Install the upper intake manifold. Use care not to pinch the injector lines between the upper and lower intake manifolds. 3. Install the upper intake manifold bolts. Note the marks made at disassembly for proper stud location. Install the two corner studs first in order to help align the two halves. AllData Editor NOTE: Other than the two torque passes listed below, the OE Manufacturer did NOT address or supply a bolt tightening sequence for the upper Intake Manifold for this model year, or other model years where this 2 piece manifold setup is used. A “Play It Safe” final tightening sequence would be to tighten from the center most bolts to the outer most bolts. 4. Tighten the bolts in two steps: a. Tighten the bolts on the first sequence to 5 Nm (44 inch lbs.). b. Tighten the bolts on the final sequence to 10 Nm (88 inch lbs.). 5. Install the purge solenoid and bracket. Refer to Powertrain Management. 6. Install the ignition coil and bracket. Refer to Starting and Charging. 7. Install the PCV hose et the upper intake manifold. 8. Install the fuel lines from the intake at the rear of the block. Refer to Powertrain Management. 9. Install the cruise control cable (if equipped). 10. Install the throttle cable and bracket from the upper intake manifold. Refer to Powertrain Management. 11. Install the wiring harness connectors and brackets. 12. Install the air cleaner assembly. Refer to Powertrain Management. 13. Connect the battery negative cable assembly to the battery negative terminal. – Tighten the bolt to 15 Nm (11 ft. lbs.).

Related entry:

remove mandafold from07rav4, bolt torque 2005 escape intake manifold, 1998 ford f150 4 2 plenum lines exploded view, torque specifications intake manifold ford 3 8L engine, how to relace a manifold on a 1995 ford e150, 2003 caravan 3 3 upper plenum torque, 3 0 merc sable intake manifold bolt torque, 2006 srx intake torque specs, how to remove intake on 2000 villager, mazda 6 intake manifold stuck open,

1997 Chevy C Tahoe Intake Manifold Replacement (Upper)

0

Filed Under (Chevrolet) by admin on 20-09-2010

download
REMOVAL 1. Disconnect the battery negative cable assembly from the battery negative terminal. 2. Remove the air cleaner assembly. Refer to Powertrain Management. 3. Remove the wiring harness connectors and the brackets and move aside. 4. Remove the throttle cable and the bracket from the upper intake manifold. 5. Remove the cruise control cable, (if equipped). 6. Remove the fuel lines from the intake to the rear of the block. Refer to Powertrain Management. 7. Remove the ignition coil and the bracket. Refer to Starting and Charging 8. Remove the upper intake manifold. INSTALLATION 1. Install the upper intake manifold gasket. 2. Install the upper intake manifold. Use care not to pinch the injector lines between the upper and lower intake manifolds. 3. Install the upper intake manifold bolts. Note the marks made at disassembly for proper stud location. Install the two corner studs first in order to help align the two halves.Other than the two torque passes listed below, the OE Manufacturer did NOT address or supply a bolt tightening sequence for the upper Intake Manifold for this model year, or other model years where this 2 piece manifold setup is used. A “Play It Safe” final tightening sequence would be to tighten from the center most bolts to the outer most bolts. 4. Tighten the bolts in two steps: a. Tighten the bolts on the first sequence to 5 Nm (44 inch lbs.). b. Tighten the bolts on the final sequence to 10 Nm (88 inch lbs.). 5. Install the purge solenoid and bracket. Refer to Powertrain Management. 6. Install the ignition coil and bracket. Refer to Starting and Charging. 7. Install the PCV hose et the upper intake manifold. 8. Install the fuel lines from the intake at the rear of the block. Refer to Powertrain Management. 9. Install the cruise control cable (if equipped). 10. Install the throttle cable and bracket from the upper intake manifold. Refer to Powertrain Management. 11. Install the wiring harness connectors and brackets. 12. Install the air cleaner assembly. Refer to Powertrain Management. 13. Connect the battery negative cable assembly to the battery negative terminal. – Tighten the bolt to 15 Nm (11 ft. lbs.).

1997 Ford Explorer LOWER INTAKE MANIFOLD REMOVAL

0

Filed Under (Ford) by admin on 09-01-2011

download
1. Remove the accelerator control splash shield. 2. Disconnect the speed control and accelerator cables from the throttle body control lever and the upper intake manifold. 3. Disconnect the intake air temperature (IAT) sensor. 4. Disconnect the fresh air tubes from the air cleaner outlet tube, then remove the air cleaner outlet tube. 5. Disconnect the idle air control (IAC) valve and the throttle position (TP) sensor. 6. Disconnect the following vacuum hoses: See Figures 1 and 2. ^ Brake booster. ^ Intake manifold tuning valve (IMTV) servo, if equipped. ^ Right side upper intake vacuum supply (two hoses). ^ PCV valve. 7. Remove the fasteners securing the EVR/VIS solenoid bracket. It is not necessary to disconnect the solenoids. Refer to Figure 2. 8. Remove the upper intake manifold screws. 9. Lift up the upper intake manifold to access the vapor management valve (VMV) hoses. Remove the locking clips and disconnect the right and left VMV hoses. See Figure 3. 10. Remove the upper intake manifold by carefully sliding the manifold off of the exhaust gas recirculation (EGR) tube. See Figure 3. 11. If equipped, position the engine vacuum reservoir aside. See Figure 4. 12. Remove the lower intake manifold. See Figure 4. CAUTION: The intake ports of the cylinder heads must be covered to avoid any foreign material from entering the engine. 13. Clean all foreign material from the intake manifold/cylinder head area, then cover the cylinder head ports with clean shop towels.

Related entry:

1995 volkswagen mk3 engine hose diagram,