How to remove Chrysler Town and Country front Bumper Cover


You are searching repair manual in PDF format about How to remove Chrysler Town and Country front Bumper Cover use another keyword for search another post or files



  How to remove Chrysler Town and Country front Bumper Cover Direct Download speed 5787 Kb/s

  How to remove Chrysler Town and Country front Bumper Cover Full Version speed 6767 Kb/s




1993 Mitsubishi Montero TRANSFER CASE DISASSEMBLY

0

Filed Under (Mitsubishi) by admin on 30-12-2010

download
Disassembly (Ram-50) 1) Remove both 4WD indicator switches and steel balls. Remove speedometer gear assembly. Remove output shaft cover, gasket, wave spring and spacer. See Fig. 3. Remove rear cover, rear cover gasket and spacer from chain cover. Drive roll pin out of high-low shift fork. 2) Remove 2 seal plugs. Remove 2 poppet springs and steel balls. Shift transfer case to “4WD” and pull high-low shift rail out, in rear cover direction. Remove interlock plunger. Remove pulse generator (if equipped), front output shaft cover and pulse rotor (if equipped). Remove snap ring from rear bearing on output shaft. Remove chain cover, oil guide and side cover. Remove countershaft locking plate. Remove countershaft. 3) Remove countergear, 2 thrust washers, 2 needle bearings and spacer through side cover opening. Remove snap ring, spring retainers and spring from 2WD-4WD shift rail. Remove front output shaft, rear output shaft and chain as assembly. 4) Remove 2WD-4WD shift fork and distance piece. Drive out 2WD-4WD shift rail spring pin. Remove 2WD-4WD shift rail and lug. Remove high-low shift fork and high-low synchronizer sleeve. Remove needle bearing and snap ring from input gear. Remove input gear assembly. 5) If either control shaft or input gear oil seals are to be replaced, drive out roll pin from transmission control change shifter. Separate transfer case from adapter. See Fig. 3. Disassembly (Montero) 1) Remove dynamic damper, 5 detection switches and 3 steel balls. Remove poppet plug, spring and steel ball. Remove speedometer gear assembly. Remove output shaft rear cover, spacers, dust seal guard and oil seals. Front output shaft cover, wave spring and spacer (if equipped). 2) Remove high-low shift rail plug and high-low shift fork spring pin. Shift transfer case to “4WD”. Remove rear cover and high- low shift rail. Remove interlock plunger. Remove rear output shaft (viscous coupling) assembly and center differential assembly. Remove 2WD-4WD synchronizer assembly, chain and front output shaft from transmission as a unit. With White paint make match marks in grooves of 2WD-4WD synchronizer in 3 places. With White paint make match marks on spline projections of 2WD-4WD synchronizer sleeve in 3 places. Refer to match marks during reassembly. 3) Remove snap ring, spring seat, spring, 2WD-4WD shift fork and 2WD-4WD synchronizer sleeve. Remove differential lock hub, oil dam cover and bearing retainer. Remove side cover and gasket. Remove transfer counter gear shaft, transfer counter gear, thrust washer, needle bearings and spacer. Remove transfer drive shaft assembly. Remove high-low shift fork assembly and clutch sleeve. Remove transfer input gear assembly. 4) Remove 2WD-4WD shift lug spring pin, spring, spring retainer 2WD-4WD shift lug and shift rail. Remove input gear oil seal, baffle plate, dust seal guard and front output shaft oil seal. See Fig. 4.

Related entry:

PT Cruiser Manual Trans Removal, removing the dash pad in a 2000 porsche boxster, how to remove a rack and pinion 2004 gmc envoy, how to take the glove box out of an avalon, remove front bumper es 300 lexus 2003, 2006 Dodge Caravan tailgate removal, challenger fron cowl removal, removing front drivers side fender S10, How to pull out rear windows in a fj40, remove gear shift knob 1996 chrysler pacifica,

1996 Ford Mustang Bumper and Bumper Cover Front Removal and Installation

0

Filed Under (Ford) by admin on 16-02-2011

download
1. Drill out four license plate rivets (if required). 2. Remove fog lamps (15200) (if equipped). 3. Remove two nuts and two screws retaining front bumper (17757) to each front fender (16005). 4. Remove one screw (3 on Cobra) retaining front bumper cover (17D957) to each front fender splash shield (16102). 5. Remove three pushpins retaining front bumper cover to radiator support (16138). 6. Remove two upper blind rivets retaining front bumper cover to radiator grille opening panel reinforcement (8A284). Front Bumper Cover 7. Remove two rivets retaining front bumper cover support (17C947) to front bumper. Remove center pins from rivets using a drift punch. Remove the remainder of the rivets using a drill. Use care not to enlarge the retaining holes in the sheet metal. 8. Remove LH and RH headlamp bulbs (13007). Refer to Section 17-01. 9. Insert a thin screwdriver blade between the underside of the front bumper cover and the radiator grille opening panel reinforcement to release the front bumper cover locking tabs on both LH and RH sides, underneath the headlamp opening. Remove the front bumper cover while the lock tabs are lifted. Front Bumper Cover Removal 11. On each side of vehicle (convertible only), remove one bolt and one nut retaining front bumper vibration damper to front bumper. Front Bumper Vibration Damper—Convertible

Related entry:

remove bumper from es 300 lexus 2003, r129 front bumper removal, chevrolet aveo rear bumper removal, 2007 camary toyota front bumper cover removal, google es 300 lexus remove bumper 2003, 2006 FORD EXPLORER Bumper Cover Retainer, how to remove front bumber toyota yaris 2003, how to remove bumper cover on 2007 aveo, remove rear bumper ford escape video instuctions, installer un bumper sur astro van,

2008 Mercury Mariner Rear Bumper Cover / Fascia Removal and Replacement

0

Filed Under (Mercury) by admin on 29-07-2010

download
BUMPER COVER – REAR Exploded View Removal and Installation 1. Remove the 2 rear bumper cover lower screws (1 each side). To install, tighten to 5 Nm (44 lb-in) . 2. Remove the 4 rear bumper cover center screws. 3. Remove the 2 rear bumper cover lower pushpins. 4. Remove the 2 rear splash shield-to-rear bumper cover screws (1 each side). 5. Remove the 2 rear bumper cover upper screws (1 each side). To install, tighten to 5 Nm (44 lb-in) . 6. Remove the 2 liftgate alignment bumper bolts and the 2 liftgate alignment bumpers. To install, tighten to 8 Nm (71 lb-in) . 7. Disconnect the parking aid system or trailer tow electrical connector, if equipped. 8. Remove the rear bumper cover. 9. To install, reverse the removal procedure. When installing, position the rear bumper cover into the bumper slides.

Related entry:

FJ CRUISER Body Armor Rear Bumper install, 2007 Saturn aura xr frame repairs,

1994 Ford Mustang A/C Evaporator Housing Removal and Installation

0

Filed Under (Ford) by admin on 06-03-2011

download
1. Disconnect battery ground cable (14301) . 2. Remove two console armrest mounting access covers (047A62) at rear of console panel (045A36) (snaps out) to gain access to armrest retaining bolts. 3. Remove four armrest-to-floor bracket retaining bolts and remove armrest assembly (snaps out of console). 4. Remove console panel gear shift plate (044G24) (snaps out). On vehicles equipped with manual transmissions, shift boot is attached to bottom of finish panel. Remove shift knob and slide boot and console panel gear shift plate up shift lever to remove. 5. To remove top finish panel position emergency brake lever in the UP position. Remove four retaining screws and lift top finish panel up. Disconnect necessary wire connectors. 6. Remove two console-to-rear floor bracket retaining screws. 7. Insert a small screwdriver into two notches at bottom of front upper finish panel and snap out. 8. If the vehicle has a radio chassis (18806) , the radio chassis must be removed. Refer to Section 15-01. If the vehicle doesn’t have a radio chassis , use a small screwdriver and pry radio cover finish panel out of console. 9. Flex glove compartment bin tabs inward. Drop down glove compartment (06010) assembly. Remove two console-to-instrument panel retaining screws. 10. Remove four console bracket retaining screws. Remove console panel from vehicle. 11. Remove three bolts retaining steering column opening cover (3A673) and reinforcement panel. Remove cover. 12. Remove steering column opening reinforcement by removing two bolts. 13. Remove two bolts retaining steering column opening reinforcement and remove reinforcement. 14. Remove six steering column retaining nuts (two retaining the hood release mechanism and four retaining column to lower brake pedal support). Lower steering column to floor. 15. Remove upper and lower steering column shrouds (3530) and disconnect wiring from turn signal and windshield wiper switch (13K359) . 16. Remove steering column through bolt and nut on engine compartment side of cowl panel. Remove steering column from vehicle. 17. Remove brake pedal support nut. 18. Snap out instrument panel defroster opening grille (044E82) . 19. Remove screws from speaker covers. Snap out speaker covers. 20. Remove front screws retaining RH and LH scuff plates at cowl side trim panels. 21. Remove RH and LH cowl side trim panels. 22. Disconnect wiring at RH cowl side. 23. Remove cowl side retaining bolts (one each side). 24. Remove five cowl top screws attachments. 25. Gently pull instrument panel (04320) away from RH side of cowl panel. Disconnect speedometer cable, air conditioning controls and wire connectors. 26. Place a drain pan or suitable container under the heater water hose connections at the cowl panel. 27. Disconnect heater water hoses (18472) from heater core tubes and plug heater water hoses with suitable 5/8-inch and 3/4-inch plugs. Cap heater core tubes to prevent coolant loss from heater core (18476) during removal of heater case. 28. Remove screw retaining A/C evaporator case support bracket (19A639) to cowl top panel. 29. Disconnect vacuum supply supply hose (black) from A/C vacuum supply in engine compartment. 30. Working under the hood (16612) , remove nut retaining heater case to cowl panel. 31. Inside passenger compartment, remove screw retaining A/C evaporator case mounting bracket (19A865) to cowl top panel. 32. Remove one screw retaining A/C evaporator case mounting bracket below heater case to cowl panel. 33. Carefully pull heater case from cowl panel and remove heater case assembly from vehicle. 34. To install, reverse Removal procedure. Check operation of all components. 35. After repairs have been completed, check the coolant level in the radiator (8005) and in the radiator coolant recovery reservoir (8A080) . Fill as required with the recommended coolant mixture.

Related entry:

remove center console e39, removal of center console 2003 suburban, ford e450 ac compressor clutch removal, how to remove the console in a Lexus GX470, headliner removel ford expedition, how to remove 1999 cavalier center console, 2010 ford 150 evaporator disassembly, equinox console removal, 2012 subaru outback tailgate panel remove, 96 cavalier remove console,

1997 Ford F-250/350/Super Duty Engine Front Cover Removal

0

Filed Under (Ford) by admin on 06-03-2011

download
Crankshaft front seal replacement is recommended whenever the engine front cover (6019) has been removed. 1. Disconnect battery ground cable (14301). Drain crankcase. 2. Drain cooling system. Refer to Section 03-03. 3. Remove drive belts (8620). Refer to Section 03-05. 4. Remove bolts attaching fan shroud (8146) to radiator (8005). 5. Remove fan blade (8600) from fan clutch (8A616) and remove fan shroud. 6. Remove fan clutch and water pump pulley (8509) from water pump (8501). 7. Disconnect upper radiator hose (8260) and lower radiator hose (8286) at engine (6007). Disconnect transmission oil cooler lines at radiator. 8. Remove upper radiator support bracket and remove radiator. 9. Remove generator pivot and attaching bolts. Remove generator (GEN) (10300) from generator mounting bracket (10153) and generator adjusting arm (10145). 10. Remove two bolts attaching generator adjusting arm to water pump and generator mounting bracket and remove generator adjusting arm. 11. Remove air pump pivot and attaching bolts. Remove secondary air injection pump (AIR pump) (9A486) from generator mounting bracket. 12. Remove four bolts attaching generator mounting bracket to cylinder head (6049), cylinder blocks (6010) and water pump, and remove generator mounting bracket. 13. Remove power steering pump pulley (3A733) from power steering pump (3A674). 14. Remove power steering lines from power steering pump. Remove four bolts attaching power steering pump to A/C compressor mounting bracket (2882) and remove power steering pump from A/C compressor mounting bracket. 15. Remove four bolts attaching A/C compressor (19703) to A/C compressor mounting bracket. Remove four bolts and one nut attaching A/C compressor mounting bracket to cylinder head and water pump. Remove A/C compressor mounting bracket from engine. 16. Remove the crankshaft pulley (6312) from the crankshaft vibration damper (6316). 17. Remove bolt and washer attaching crankshaft vibration damper. Remove crankshaft vibration damper using Crankshaft Damper Remover T58P-6316-D or Rotunda Gear and Pulley Puller 014-00293 or equivalent. Remove Woodruff key and crankshaft damper spacer from crankshaft (6303).

Related entry:

2000 blazer vapor canister mounting bracket, vapor canister blazer bracket, navistar clean feed power cable, installing front license plate bracket on 2004 ford freestar minivan, how to remove clutch fan on navigator 5 4 dohc, ford contour crankshaft pulley removal, crankshaft pulley 1996 ford contour, audi a4 fan pulley removal, 2002 cavalier brake caliper slide pin torque value, wiring ac kompresser kancil,