Filed Under (Mercedes-Benz) by admin on 10-05-2010
The fuse/relay box is located in the left side of the engine compartment. Relay and Control Unit Locations Fuse Box and Fuse Location (Fuses 1 – 4) Fuse Box and Fuse Location (Fuses G, H, F10, F15, F22, F22/1,
F22/2) Fuse Box and Fuse Location (Fuses F24 & F24/1)
Filed Under (Mitsubishi) by admin on 07-06-2010
Valve timing procedures Valve timing procedures Ensure crankshaft at TDC on No.1 cylinder. Ensure crankshaft pulley timing mark aligned with 0° timing mark on chain cover . Ensure notch on camshaft points upwards . If notch not visible, turn crankshaft one more turn. Install timing gears as follows: Ensure crankshaft gear and intermediate shaft gear timing marks aligned . Install LH balancer shaft . Ensure timing marks on intermediate shaft gears and LH balancer shaft gear aligned  & . Ensure RH balancer shaft gear and oil pump gear timing marks aligned . Install oil pump housing complete with RH balancer shaft. Ensure timing marks on oil pump gear and crankshaft gear aligned . Install injection pump as follows  : Ensure notch on injection pump gear aligned with mark ‘T’ on flange . During installation of injection pump: Notch on gear moves in direction of arrow. Install timing chain as follows:
Filed Under (Volvo) by admin on 14-05-2010
Fuses Panel Locations Fuses 11A/1 To 11A/9 & 11B/1 To 11B/5 In Relay Fusebox In Engine Compartment Relays Panel Locations Other Relays 2/11 Relay engine coolant fan (FC) 2/43 Relay heated rear seat (S70/V70) 2/54 Relay coolbox (V70)
2/74 Relay heating plugs coolant (Diesel) 7/1 Bulb failure warning sensor rear 11C/1-40 Fuses 1/1 Battery 2/35 Starter motor relay 2/76 Central locking/anti theft alarm (lock/alarm) control module 3/1 Ignition switch 3/71 Gear position sensor 4/9 SRS Supplemental Restraint System Crash Sensor 4/30 ECC climate control module 5/1 Combined instrument panel 6/25 Starter motor 6/26 Generator
24/2 Connector Firewall cable harness – Engine compartment harness 24/13 Connector Dashboard harness – Engine compartment harness 24/14 Connector Left door sill harness – Engine compartment harness 24/15 14-pin connector Engine compartment harness – engine harness 24/43 8-pin connector Engine compartment harness – engine harness 24/53 26-pin connector Engine harness – AW 50-42 31/4 Engine ground point (ground terminal – battery-engine) 31/7 Ground terminal driver’s side A post 31/44 Engine compartment ground point (battery ground terminal – body)
Filed Under (Mitsubishi) by admin on 20-12-2010
Exhaust System Removal Note: With a used vehicle, we suggest a penetrating spray lubricant to be applied liberally to all exhaust fasteners and al- lowing a significant period of time for the chemical to lubricate the threads before attempting to disassemble. 1. Unbolt the flange located just in front of the rear muffler as shown in. (figure 1) 2. Lubricate all the hangers and rubber isolators. 3. Using a muffler stand or an additional person to hold the rear muffler into position, remove the hangers from the rub- ber isolators and remove the rear muffler from the vehicle as shown. (figure 2) 4. Unbolt the flange located just behind the catalytic converter as shown. (figure 3) 5. Place hardware and gasket to the side for use during the installation of your new exhaust system. Using a muffler stand or an additional person to hold the front muffler assembly into position, remove the bolt from the rubber isolator and remove the front muffler assembly from the vehicle as shown. (figure 4) 1. Using the original hardware and gasket, place the muffler assembly into position as shown. Hand tighten the hardware for now. (figure 5) 2. Place a clamp over the expanded end of the intermediate pipe and set it into position as shown making sure to install the hanger into the rubber isolator. Do Not tighten the clamp. (figure 6) 3. Place a clamp over the expanded end of the tail pipe assem- bly and set it into position as shown making sure to install the hangers into the rubber isolators. Do Not tighten the clamp. (figure 7) 4. Check your exhaust system for proper clearance under the vehicle and also for tip alignment.
Filed Under (Mitsubishi) by admin on 18-12-2010
Function The original intercooler for the L200 is quite small. Because of this the cooling capacity is low and the pressure drop is considerable. When increasing the power output of the L200 engine the boost air temperature must be kept as low as possible, while it has a great influence in performance as well as engine durability. Charge air cooling also has a positive effect on exhaust emissions from diesel engines. The pressure drop through the charge air cooler lowers the air mass flow trough the engine. To maximize air mass flow is essential to increase performance. The sttemtec charge air cooler upgrade maximizes the cooling capacity and minimizes the pressure drop of the charge air cooler without any negative effects of the vehicle. List of content 1. Charge air cooler 2. Air hose 3. Bag, Brackets and rubber mountings for intercooler Installation Installation preparations 1. Perform test drive with verification of general engine functions. 2. Wash engine bay with special attention to radiator and intercooler (wash, compressed air). System installation Remove the radiator grille by first remove the four plastic clips and then the claws by pulling out and up.