Peugeot 307 vacuum


You are searching repair manual in PDF format about Peugeot 307 vacuum use another keyword for search another post or files



  Peugeot 307 vacuum Direct Download speed 5787 Kb/s

  Peugeot 307 vacuum Full Version speed 6767 Kb/s




2004 Jeep Grand Cherokee Limited DIAGNOSIS AND TESTING – VACUUM RESERVOIR

0

Filed Under (Jeep) by admin on 18-11-2010

download
1. Disconnect vacuum hose at speed control servo and install a vacuum gauge into the disconnected hose. 2. Start engine and observe gauge at idle. Vacuum gauge should read at least ten inches of mercury. 3. If vacuum is less than ten inches of mercury, determine source of leak. Check vacuum line to engine for leaks. Also check actual engine intake manifold vacuum. If manifold vacuum does not meet this requirement, check for poor engine performance and repair as necessary. 4. If vacuum line to engine is not leaking, check for leak at vacuum reservoir. To locate and gain access to reservoir, refer to Vacuum Reservoir REMOVAL /INSTALLATION . Disconnect vacuum line at reservoir and connect a hand-operated vacuum pump to reservoir fitting. Apply vacuum. Reservoir vacuum should not bleed off. If vacuum is being lost, replace reservoir. 5. Verify operation of one-way check valve and check it for leaks. a. Locate one-way check valve. The valve is located in vacuum line between vacuum reservoir and engine vacuum source. Disconnect vacuum hoses (lines) at each end of valve. b. Connect a hand-operated vacuum pump to reservoir end of check valve. Apply vacuum. Vacuum should not bleed off. If vacuum is being lost, replace one-way check valve. c. Connect a hand-operated vacuum pump to vacuum source end of check valve. Apply vacuum. Vacuum should flow through valve. If vacuum is not flowing, replace one-way check valve. Seal the fitting at opposite end of valve with a finger and apply vacuum. If vacuum will not hold, diaphragm within check valve has ruptured. Replace valve.

Related entry:

vacuum hoses routing 4x4 01 ram 1500, 2007 ford f150 vacuum fitting connection, vacuum diagram 2003 ford ranger, vacuum hoses routing for 2E toyota engine, vacuum line diagram for 1988 4 3 engine, 1980 280zx vacuum diagram, 2001 gm savanna 5 7 vacume hose diagram, 2003 silverado vacuum lines, location of vacuum hoses on a 2007 ford edge, 2001 oldsmobile aurora 3 5 vacuum line diagram,

2005 Chevrolet Malibu Vacuum Brake Booster Check Valve and/or Hose Replacement Removal Procedure

0

Filed Under (Chevrolet) by admin on 19-10-2010

download
1. Disconnect the brake booster vacuum check valve (1) from the brake booster. 2. If the vacuum check valve (1) needs to be separated from the vacuum hose (3), release and reposition the clamp (2) on the vacuum hose (3) and remove the check valve (1) from the hose (3). 3. If replacing the vacuum check valve (1), remove the grommet (4) from the brake booster and discard the grommet. 4. If removing the vacuum hose (2), take note of the vacuum hose routing then disconnect from the engine intake manifold connection (3) by releasing tension on the vacuum hose clamp (1) and sliding the vacuum hose (2) off the intake manifold connection (3). Installation Procedure Important: A small amount of denatured alcohol can be used as an assembly aid when installing the vacuum check valve and/or grommet. Do NOT use soap. 1. If the vacuum hose (2) was removed, install the vacuum hose into position on the vehicle as noted prior to removal, then connect the vacuum hose (2) to the engine intake manifold connection (3) and secure with the vacuum hose clamp (1). 2. If the vacuum check valve (1) is being replaced, install a NEW grommet (4) to the brake booster. 3. If the vacuum check valve (1) was separated from the vacuum hose (3), install the check valve (1) to the vacuum hose (3). Install and secure the clamp (2) into position on the hose (3). 4. Connect the brake booster vacuum check valve (1) to the brake booster.

Related entry:

2002 3 0 s-type vacuum hose diagrahm, cruise control vacum digram 1980 corvette, 2000 navigator heater hose removal, discovery 2004 brake booster vacuum hose fitting, 2004 navigator hose diagram, 5 4 triton engine vacuum line to brake booster, 99 civic ex vacuum line pinch on manifold, 99 contour vacuum hose diagram, 1999 vw passat 1 8t vacuum check valve diagram, 2006 chrysler pacifica cruscontrol vacume digram,

PEUGEOT 307 – ELECTRO HYDRAULIC POWER STEERING PROBLEM

0

Filed Under (Peugeot) by admin on 17-04-2010

download
Fault Caller reported that the Electro Hydraulic Power Steering system (EHPS) was not operating after a low speed accident.
Cause
Peugeot dealer reported that if the vehicle is involved in an accident impact which is in excess of approx 1g of impact force, the EHPS control module (ECM) will default to an accident safe mode. Vehicles
Rectification
In the accident safe mode, the electro-hydraulic power steering system defaults to minimum power steering assistance and will not return to normal operation until the EHPS is interrogated with self diagnostic equipment to check for fault codes, and if no faults are found the EHPS, is reset

Related entry:

1 6 hdi 307 manual gearbox removal pdf, adjuat a gear box on a peugeot 307 cc, byte tändstift peugeot, dash board peugeot 307 schema wiring, P0105 PEUGEOT, p0105 peugeot 207, peugeot 307 sw 2005 manual, peugot 307 hood switch, track rod removal on a peugoet 307,

2002-2003 Saturn VUE (Retorque Intake Manifold Vacuum Chamber Bolts, Install Vacuum Chamber Springs)

0

Filed Under (Saturn) by admin on 04-06-2010

download
Condition Some customers may comment on the (MIL) SERVICE ENGINE SOON telltale being illuminated. (DTC(s) P0171 – Fuel Trim System Lean Bank 1 and/or DTC P0174 – Fuel Trim System Lean Bank 2 may be set and stored in the ECM memory.) Cause This condition may be caused by insufficient torque on the intake manifold vacuum chamber bolts. Under deceleration, enough vacuum can be created inside the intake manifold to lift the vacuum chamber off it’s seal creating an intermittent vacuum leak. Correction Refer to the service procedure in this bulletin to retorque the intake manifold vacuum chamber bolts and install the vacuum chamber springs. Procedure: Notice: When servicing intake manifold, do not use power tools. Damage to threads or manifold may occur. 1. Loosen clamp at air cleaner assembly and throttle body assembly. 2. Remove attachment bolts from outlet resonator/duct assembly.

Related entry:

decarbonize combustion chamber,

1998-2000 Honda Accord Moisture in the fuel pressure regulator

0

Filed Under (Honda) by admin on 29-12-2010

download
1. Locate and identify the three vacuum ports on the intake manifold. 2. Disconnect and discard the vacuum hose that connects the fuel pressure regulator to vacuum port C. 3. Plug vacuum port C with the cap from the tube kit. 4. Replace the fuel pressure regulator. Refer to page 11-113 of the 1998-00 Accord Service Manual. 5. Install the new vacuum hose kit using one of the following procedures. M/T WITH CRUISE CONTROL 1. Remove and discard the cap from vacuum port A. 2. Connect the short vacuum hose to vacuum port A. 3. Anchor the long vacuum hose by attaching it to the rear intake air duct clip and to the cruise control hose. 4. Route the new vacuum hose to the fuel pressure regulator. Attach the hose to the three rear clips on the engine wire harness cover. A/T WITH CRUISE CONTROL 1. Remove and discard the vacuum hose from vacuum port A. This hose supplies vacuum to the rear engine mount control solenoid. 2. Connect the short vacuum hose from the top of the Y fitting to vacuum port A.