Rover 416 SLi


You are searching repair manual in PDF format about Rover 416 SLi use another keyword for search another post or files



  Rover 416 SLi Direct Download speed 5787 Kb/s

  Rover 416 SLi Full Version speed 6767 Kb/s




Airbag diagnostics – Rover Metro • Rover 100 • New Rover 400 • Rover 600

0

Filed Under (Rover) by admin on 23-05-2010

download
some models, no serial diagnostics are available with the airbag system. On these systems, faults are reported by means of the Airbag warning light on the dashboard. The Rover models concerned are as follows: • Metro • Rover 100 • New Rover 400 • Rover 600
ED3 Airbag For the ED3 system on Metro, Rover 100, and New Rover 400 vehicles, the airbag warning light has the following meaning.
Warning light behavior when Meaning ignition is switched on. Comes on then goes off after No fault in system 3 seconds. Comes on and stays on Fault in airbag module, SRS ECU, cabling, or airbag module connector Comes on, goes off after 3 Fault in airbag module, SRS seconds, then comes back on ECU, cabling, or airbag and remains on. module connector

Related entry:

rover 620 wurkshop manual free pdf dawnload, ecu pinout rover 600, geo metro remove airbag, Rover 25 Manual Free Download, 2002 Rover 25-workshop manual-free download, CODE LIGHT MEANING FOR 2006 TORENT, rover 620 repair manual free download, User manual for 2002 Rover 25 series, warning signs of rover 75 and pictures,

Diagnostic connector location – Rover / MG

0

Filed Under (Rover) by admin on 20-06-2010

download
Rover 100 16 pin CAN1 In fuse compartment Rover 200 16 pin CAN1 Behind central console, on end of a free cable. Rover 200 3 pin – Engine MEMS In engine bay beside ECU Rover 200 3 pin – Security A0903111-1 Rear of engine bay New Rover 200 16 pin CAN1 Drivers side, On side of central column. Rover 400 16 pin CAN1 Above pedals, on the end of a free cable. Rover 400 3 pin – Engine A0903111-1 In engine bay beside ECU Rover 400 3 pin – Security A0903111-1 Rear of engine bay New Rover 400 16 pin CAN1 Drivers side, On side of central column. Rover 600 16 pin CAN1 In front of drivers seat above pedals Rover 600 Honda PGM-Fi Honda PGM-Fi Passenger footwell, behind triangular panel just in front of door hinge. Rover 800 16 pin CAN1 Drivers side of central column Rover 800 3 pin – Engine MEMS In engine bay beside ECU Rover 800 4 pin – Security A0903111-1 Bottom of dash, below steering wheel. Rover 25 16 pin CAN1 Drivers side, On side of central column.

2006 Land Rover Range Rover Sport Parking Brake Actuator Removal

0

Filed Under (Rover) by admin on 24-10-2010

download
1. Using the Land Rover approved diagnostic system, drive the parking brake to the ‘mounting position’. 2. Isolate the parking brake electrical circuit. Remove fuse number 8 from the BJB. WARNING: Do not work on or under a vehicle supported only by a jack. Always support the vehicle on safety stands. 3. Raise and support the vehicle. 4. Remove the rear wheels and tires. 5. Release the parking brake shoe adjustment. Remove the plug from the access hole in the brake disc. Using a suitable tool, rotate the brake shoe adjuster to release the adjustment. CAUTION: Do not allow the brake caliper to hang on the brake hose. 6. Reposition the RH rear brake caliper. Remove the 2 bolts. Using a suitable tie strap, support the brake caliper. 7. Remove the RH rear brake disc. Remove the screw. CAUTION: Do not allow the brake caliper to hang on the brake hose. 8. Reposition the LH rear brake caliper. Remove the 2 bolts. Using a suitable tie strap, support the brake caliper. 9. Remove the LH rear brake disc. Remove the screw. 10. Disconnect both parking brake cables from the wheel hubs. Fully loosen the nut. Release the cable from the lower arm. Disconnect the inner cable from the brake shoe 11. Release the LH parking brake cable. Remove the 2 bolts. Release the 3 wiring harness clips. Release the cable from the clip on the chassis.

Related entry:

vp37 wiring, 04 land rover free lander timing marks, 2002 land rover freelander ecm reprogram, evap system purge valve 1998 rang rover, free manual for timing range rover, landrover fault code 1260, torque for range rover sport brake,

2006 Land Rover Range Rover Sport Parking Brake Shoes Removal

0

Filed Under (land rover) by admin on 18-10-2010

download
NOTE: If the parking brake shoes or the brake discs have been removed for access to other components then DO NOT carry out the bedding in procedure. 1. Using the Land Rover approved diagnostic system, drive the parking brake to the mounting position. 2. Isolate the parking brake electrical circuit. Remove fuse number 8 from the BJB. 3. WARNING: Do not work on or under a vehicle supported only by a jack. Always support the vehicle on safety stands. Raise and support the vehicle. 4. Remove the wheels and tires. 5. Release the brake caliper. Remove the brake caliper anchor bolts. 6. CAUTION: Do not allow the brake caliper to hang on the brake hose. Tie the brake caliper aside. 7. Release the park brake shoe adjustment. Remove the plug from the access hole in the brake disc. Using a suitable tool, rotate the brake shoe adjuster to release the adjustment. 8. Remove the brake disc. Remove the Torx screw. 10. Remove the primary brake shoe. Remove the hold-down spring and retaining pin. Pivot the shoe to release it from the spreader plate and return spring. 11. Remove the spreader plate and spring. 12. Remove the return spring. Remove the hold-down spring and retaining pin. Disconnect the parking brake cable retaining spring from the brake shoe lever. Release the parking brake cable.

Related entry:

2006 range rover hse firing order, Haley detection pump on a 04 Land Rover freelandet,

2005 Land Rover Range Rover Fuel Rail: Service and Repair

0

Filed Under (Rover) by admin on 25-08-2010

download
Before disconnecting the battery, ensure all text and cautions in the battery disconnection section are observed. Remove 1. Disconnect battery earth lead. 2. Remove air intake hose. 3. Remove LH ignition coil cover. 4. Remove RH ignition coil cover. 5. Disconnect multiplugs from ignition coils. 6. Disconnect multiplugs from throttle body, thermostat heater, CMP sensor and ECT sensor. 7. Cut 2 cable ties and release engine harness. 8. Disconnect multiplugs from VCC solenoids. 9. Release VCC multiplug harness from clip. 10. Disconnect multiplug from charcoal canister purge solenoid valve. 11. Disconnect alternator multiplug. 12. Release alternator harness from 4 clips. 13. Disconnect multiplugs from KS and CMP sensor. 14. Remove 2 nuts securing fuel injector harness to fuel rail. 15. Release vacuum reservoir and mounting bracket from LH fuel injector harness securing stud. 16. Remove fuel hose and mounting bracket from LH fuel injector harness securing stud.