TOYOTA CRESSIDA 21R DUAL CARBURETOR


You are searching repair manual in PDF format about TOYOTA CRESSIDA 21R DUAL CARBURETOR use another keyword for search another post or files



  TOYOTA CRESSIDA 21R DUAL CARBURETOR Direct Download speed 5787 Kb/s

  TOYOTA CRESSIDA 21R DUAL CARBURETOR Full Version speed 6767 Kb/s




1994 Ford Mustang Dual Converter and Pipe 5.0L Engine Removal Installation

0

Filed Under (Ford) by admin on 07-02-2011

download
5.0L Engine Removal 1. Raise vehicle. Refer to Section 00-02. 2. Disconnect air inlet tube (5F235) from the dual converter and pipe. 3. Remove dual converter and pipe to exhaust manifold retaining nuts. 4. Remove muffler inlet flange to dual converter and pipe outlet flange retaining nuts. 5. Support dual converter and pipe with a suitable jackstand and remove exhaust converter frame bracket to dual converter and pipe retaining nuts. 6. Remove dual converter and pipe from vehicle. 7. Replace any damaged parts. Installation 1. Loosely install dual converter and pipe and support with a suitable jackstand. 2. Install dual converter and pipe onto exhaust converter frame bracket (5E269) and install retaining nuts. Tighten retaining nuts to 14.8-20.2 Nm (11-15 lb-ft). 3. Position dual converter and pipe to exhaust manifold studs and install retaining nuts. Do not tighten nuts. 4. Position muffler inlet flanges to dual converter and pipe outlet flanges and install retaining nuts. Do not tighten nuts. Remove jackstand. 5. Align exhaust system to specification, refer to appropriate illustration. 6. With exhaust system aligned: a. Tighten dual converter and pipe-to-exhaust manifold nuts to 34-46 Nm (25-34 lb-ft). b. Tighten muffler inlet flanges-to-dual converter and pipe outlet flanges retaining nuts to 29.7-40.3 Nm (22-30 lb-ft). 7. Attach air inlet tube to dual converter and pipe. Tighten clamp securely. 8. Check system for leaks and lower vehicle. 3.8L Engine Removal 1. Raise vehicle. Refer to Section 00-02. 2. Remove dual converter and pipe-to-exhaust manifold retaining nuts. 3. Remove dual converter and pipe outlet flange to muffler inlet flange retaining nuts. 4. Support dual converter and pipe with a suitable jackstand and remove exhaust converter frame bracket to dual converter Y pipe retaining nuts. 5. Remove dual converter and pipe from vehicle. 6. Replace any damaged parts. Installation 1. Loosely install dual converter and pipe and support with a suitable jackstand. 2. Install dual converter and pipe onto exhaust converter frame bracket and install retaining nuts. Tighten retaining nuts to 14.8-20.2 Nm (11-15 lb-ft). 3. Position dual converter and pipe to exhaust manifold studs and install retaining nuts. Do not tighten retaining nuts. 4. Position muffler inlet flange to dual converter and pipe outlet flange. Loosely install retaining nuts. 5. Align exhaust system to proper clearance specifications, as shown in the appropriate illustration. 6. With exhaust system aligned: a. Tighten dual converter and pipe to exhaust manifold nuts to 34-46 Nm (25-34 lb-ft). b. Tighten muffler inlet flange to dual converter and pipe flange retaining nuts to 29.7-40.3 Nm (22-30 lb-ft). 7. Check exhaust system for leaks.

Related entry:

flex pipe flange kit 2008 cobalt, 2008 cobalt flex pipe flange, 2007 ford explorer exhaust diagram, 2005 mercury sable exhaust flex flange repair, 2002 mazda tribute catalytic converter installation and removal, 2001 rav4 heat shield clamp, repair F87F-18C868-DD, p/n 06175-p8ca00, how to replace radiator inlet pipe on a 1998 cavalier, how to repair hhr sun visor,

WATER LEAK AT FRONT FLOOR ’02 – ’06 Toyota Camry (TMMK), ’04 – ’06 Toyota Solara Coupe, & ’05 – ’06 Toyota Avalon

0

Filed Under (Toyota) by admin on 04-06-2010

download
Some customers may experience a water leak at the front floor area. Water may be Introduction entering the body due to a body sealer void on the engine compartment rear wall, near the upper door hinge. Repair 1. Raise the vehicle. On the side of the vehicle that has the water leak, remove the front Procedure wheel and the front fender plastic liner. 2. Examine (with flash light and mirror) the body sealer condition on the engine compartment rear wall, near the upper door hinge. Also examine the sealer condition inside the inner fender box frame structure with access holes (see illustration).

Related entry:

toyota crown royal saloon manual, 2000 avalon trunk release mechanism removal, po352 toyota avalon 2006, avensis gearbox dismantel manual, toyota tacoma 3400 four cam fuel line connections, toyota starlet kp61 maintenance booklet free download, toyota innova car repair mannual, how to change a toyota avensis fuse, ACR50 P0717, toyota passo service manual,

COLD AIR SYSTEM Installation Instructions 2003-2004 Toyota Corolla 2002-2004 Toyota Matrix XR

0

Filed Under (Toyota) by admin on 16-04-2010

download
Removing the stock air inlet system
a) Before removing any of the O.E. components, label each individual part so that no components become mixed up during the installation process. There are two Vacuum Switching Valves (VSV), and one air flow meter that have electrical and/or vacuum connections going to them. Be sure to label these connections before disconnecting them.
Remove b) Remove the two nuts and two plastic rivets that hold the plastic engine cover on. The
plastic rivets may be gently lifted with a small screwdriver. Remove the cover. c) Remove the bolt in the radiator support that holds the battery bracket. Unhook the rod at the rear of the battery bracket. Remove the battery from the vehicle

Related entry:

REMOVING toyota matrix ecm, 89 corolla gts tps adjustment, 05 sequoia fuse diagram, 2004 toyota rav 4 cylinder head torque sequence, 2004 toyota estima manual, evap vacuum switch valve diagram 02 4runner, R&R thermostat on 2003 toyota matrix, procedure to replace ecu of 2004 toyota corolla, p 0456 matrix, NZE Toyota Corolla 2004,

Toyota 2H, 12H-T Engine Repair Manual for Toyota Land Cruiser

0

Filed Under (Toyota) by admin on 11-09-2009

Applicable for Toyota Land Crusier HJ60, 61, 75 series
Table of Content1. Introduction 2. Engine Mechanical 3. Fuel System 4. Cooling System 5. Lubrication System
6. Starting System 7. Charging System 8. Service Specifications 9. Standard Bolt Torque Specifications
10. SST and SSM

Toyota B & 2B Engine Manual for Toyota Land Cruiser

0

Filed Under (Toyota) by admin on 11-09-2009

applicable for Toyota Land Cruiser BU20, 30 series, BB10 series, BJ40, 43 series
Table of Content
1. General
2. Engine Tune up
3. Engine Service
4. Lubrication System
5. Cooling System
6. Fuel System
7. Edic System
8. Starting System
9. Charging System
10. SST & Service Specifications

Related entry:

how to locate hj60 edic control,