air fuel mixture adjustment for 4g13 engine


You are searching repair manual in PDF format about air fuel mixture adjustment for 4g13 engine use another keyword for search another post or files



  air fuel mixture adjustment for 4g13 engine Direct Download speed 5787 Kb/s

  air fuel mixture adjustment for 4g13 engine Full Version speed 6767 Kb/s




1998 Ford F-150/250 Fuel Charging and Controls DESCRIPTION AND OPERATION

0

Filed Under (Ford) by admin on 25-03-2011

download
Fuel Charging and Controls The fuel charging and controls system consists of: fuel pressure regulator (9C968) fuel injection supply manifold (9F792) fuel injectors (9F593) fuel shut off valve solenoid (9D278) fuel pressure relief valve (9H321) injection pressure sensor engine fuel temperature sensor fuel charging wiring harness Component Location Fuel Pressure Regulator The fuel pressure regulator is located on the inside of the LH frame rail just forward of the transmission support crossmember. It is part of an assembly that includes the coalescer/filter. The fuel pressure regulator reduces the line pressure from tank pressure 20685 kPa (3000 psi) to line pressure 655 kPa (95 psi). Heating/Defrosting—Natural Gas Vehicle Fuel pressure regulator heating is provided by two 3/8-inch taps from the existing heater supply and return hoses on the RH rear of the engine. Two high-temperature 3/8-inch ID heater hoses (packaged with the front low-pressure fuel line) are used to connect the fuel pressure regulator to the tap points on the engine heater hoses. Refer to the Line — Low Pressure Fuel procedure in Section 310-01B for fuel pressure regulator heater hose replacement. Fuel Pressure Regulator Heater Hoses Fuel Injection Supply Manifold The fuel injection supply manifold delivers high-pressure fuel from the vehicle fuel supply line to the fuel injectors. The fuel injection supply manifold consists of the following: a tubular fuel rail eight fuel injector connectors a fuel pressure relief valve a fuel shut off valve solenoid mounting attachments which locate the fuel injection supply manifold and provide fuel injector retention. a fuel inlet connection which has a push-connect fitting an injection pressure sensor an engine fuel temperature sensor Fuel Injection Supply Manifold Fuel Injectors The natural gas fuel injectors are electro-mechanical devices that meter fuel delivered to the engine. The natural gas fuel injectors are mounted in the lower intake manifold (9424) and are positioned so that their tips direct fuel just ahead of the engine intake valves (6507). The natural gas fuel injector bodies consist of a solenoid and a needle and valve assembly. Natural gas fuel injectors can be identified by an aqua cap on the injector body. Fuel Shutoff Valve Solenoid The fuel shut off valve solenoid seals the upstream fuel pressure from entering the fuel injection supply manifold when the engine is not running. The fuel shut off valve solenoid is open only when it is activated by the solenoid valve (fuel pump) relay. Fuel Pressure Relief Valve The fuel pressure relief valve is located on the fuel injection supply manifold, and is used to relieve fuel system pressure from the fuel delivery system. Injection Pressure Sensor The injection pressure sensor is located on the fuel injection supply manifold, and is used to provide a signal to the powertrain control module (PCM) (12A650) that is proportional to pressure in the fuel injection supply manifold. Engine Fuel Temperature Sensor The engine fuel temperature sensor is located on the fuel injection supply manifold, and is used to provide a signal to the powertrain control module that indicates the temperature of the fuel in the fuel injection supply manifold. Fuel Charging Wiring The fuel charging wiring is a single harness that includes electrical connectors for the fuel injectors, ignition coils and various sensors, valves and senders that monitor all engine functions. Fuel Charging Wiring

Related entry:

1980 gas tank wiring harness, 2006 sorento gas gage problems, how to repair a gas gauge in 3000 mistubishi diagrams, 92 f150 fuel pressure relief, 2003 lincoln navigator fuel pump shut off switch, 2001 MATIZ HOW TO CONNECT A FUEL FILTER, how to replace gas cap door sensor on a 2001 honda oddessy, nissan navara d40 reset fuel pressure, nissan navara d22 non retern fuel valve, 2004 ford explorer Line pressure solenoid B valve harness,

1997 Jeep Wrangler SE FUEL PRESSURE RELEASE Fuel Rail With Fuel Pressure Test

0

Filed Under (Jeep) by admin on 27-12-2010

download
FUEL PRESSURE RELEASE Fuel Rail With Fuel Pressure Test Port 1. Disconnect negative battery cable. Remove fuel tank cap to release fuel tank pressure. 2. Remove protective cap from fuel pressure test port on fuel rail. Place one end of Fuel Pressure Gauge (5069) hose into approved gasoline container. Screw remaining end of fuel pressure gauge hose onto fuel pressure test port. Fuel pressure will be released into gasoline container. 3. After fuel pressure is released, remove fuel pressure gauge hose from fuel pressure test port. Reinstall protective cap on fuel pressure test port and fuel tank cap. Reinstall negative battery cable. Fuel Rail Without Fuel Pressure Test Port 1. Remove fuel pump relay from Power Distribution Center (PDC), located near windshield washer reservoir. Refer to label on PDC cover for relay location. 2. Start engine and allow to idle until engine stalls. Attempt to start engine several times. Once engine will not restart, turn ignition off. 3. Disconnect electrical connector from any fuel injector. Connect a jumper wire between one fuel injector terminal and positive battery terminal. Connect another jumper wire to remaining fuel injector terminal. CAUTION: DO NOT apply battery voltage to fuel injector for more than 4 seconds, or fuel injector may be damaged. 4. Momentarily touch remaining end of jumper wire to negative battery terminal for no more than 4 seconds. Cover fuel line at fuel rail with shop towel before disconnecting. Disconnect fuel line. 5. Disconnect jumper wires. Reinstall electrical connector on fuel injector. Reinstall fuel pump relay. Diagnostic Trouble Codes (DTCs) may be stored in Powertrain Control Module (PCM) when ASD relay is removed. To clear DTCs from PCM, see TESTS W/CODES – 2.5L article. FUEL PRESSURE TEST

Related entry:

2001 honda accord low pressure service port, where is low pressure port on 2001 mazda tribute, where is low pressire port on 2000 dodge caravan, where is the ac low port on 2008 escalade, diagram of 2003 chevy impala ls a/c low pressure port, low pressure port ac 2000 cadillac escalade, release fuel pressure on 2001 honda accord, where to find low pressure port on a 2002 cadillac deville, 2001 yukon ac low pressure port, 1991 toyota camry ac low pressure port,

1997 Isuzu Rodeo S FUEL PUMP PRESSURE TEST

0

Filed Under (Isuzu) by admin on 23-12-2010

download
NOTE: 1. Release fuel pressure. See FUEL SYSTEM PRESSURE RELEASE . Install a fuel pressure gauge between fuel pressure regulator and fuel distributor pipe. See Fig. 1 . Bleed air from fuel line going to pressure gauge. 2. Unplug fuel pressure regulator Vacuum Switching Valve (VSV) connector on right side fender skirt. This is a 4-wire connector with Black and Blue wires in harness. PCM controls VSV to cut vacuum to fuel pressure regulator during hot engine starts. 3. Start engine and measure fuel pressure at idle. Disconnect fuel pressure regulator vacuum hose. Note fuel pressure at idle with vacuum hose disconnected (no vacuum). Fuel pressure should be 42 psi (3.0 kg/cm2 ). See FUEL PUMP PERFORMANCE . 4. If fuel pump pressure is low, check for fuel leaks, restrictions in intake side of fuel pump, leaking injectors, faulty pressure regulator or faulty fuel pump. If fuel pressure is high, check for restrictions in return line to tank or faulty pressure regulator. If pressure does not change when pressure regulator is disconnected, replace pressure regulator. 5. Reconnect pressure regulator vacuum hose and check fuel pressure (with vacuum). Fuel pressure should be 35 psi (2.4 kg/cm2 ). Apply battery voltage to VSV connector Blue wire terminal, and ground Black wire terminal (with vacuum). See Fig. 2 . Fuel pressure gauge should read about 42 psi (3.0 kg/cm2 ). If fuel pressure is not within specification, check for defective VSV. 6. Disconnect and plug vacuum hose from fuel pressure regulator. Stop engine and ensure fuel pressure remains greater than 35 psi (2.4 kg/cm2 ) for 4 minutes after engine stops. 7. If pressure drops, check for leaking injectors, faulty pressure regulator or bad check valve in fuel pump. If engine does not start, by-pass fuel pump relay to check for fuel pressure. Remove fuel pump relay from underhood fuse/relay box. Connect a fused jumper wire between terminals No. 1 and 3 of fuel pump relay connector in fuse block. See Fig. 3 and Fig. 4 . 8. If fuel pump does not operate, check for battery voltage to terminal No. 3. If battery voltage is present, check for open in fuel pump circuit. If fuel pump operates with jumper wire installed, check fuel pump relay and relay energizing circuit. Repair as necessary. Begin basic fuel system diagnosis with testing fuel pressure.

Related entry:

how to relieve injector pressure on 2001 pt cruiser, how to repair ac low side nipple, 2001 Pontiac Montana fuel injector connector release how to, 1990 passat starts and stalls, 1998 chevy silverado fuel system pressure measurement, 96 vw rear brake pressure regulating valve diagram, 300d turbo boost measurement, fuel regulator open sedona, where is the fuel pressure test port on a 2001 mercury cougar, gmc jimmy pump fuel regulator installation,

2005 GMC Sierra 2500 Fuel System Diagnosis

0

Filed Under (GM) by admin on 27-10-2010

download
FUEL SYSTEM DESCRIPTION Fuel is drawn by the supply pump through a pre-filter screen in the tank and to the engine through the fuel supply lines. There is no lift pump in the fuel tanks or on the frame. The fuel passes through the base plate of the fuel injector control module (FICM) to cool the module. From the FICM the fuel flows to the fuel filter/heater element housing, which combines a water separator, a prime pump, a fuel heater element and a filter element. The fuel is then delivered to the high-pressure pump. An integrated hand pump is used to prime the fuel system after changing the fuel filter or servicing the fuel system. The fuel injection pump at the front of the engine valley includes the fuel supply pump and the high-pressure pump. If the fuel system is not suppling enough fuel, a driveability concern may occur. If air is being drawn into the fuel injection system, a Cranks But Will Not Run or Hart Start symptom could exist. HIGH PRESSURE SYSTEM The much larger section of the pump assembly is the high-pressure fuel injection pump. The pump is engine-driven by the camshaft gear. From the high-pressure pump, the pressurized flows to the left common fuel rail. A balance pipe from the center of the left rail then feeds the right common fuel rail. Each common fuel rail supplies one bank of 4 fuel injectors. The fuel rail pressure sensor is mounted in the middle of the right common fuel rail. RETURN SYSTEM The fuel return system routes fuel from the fuel injectors and the fuel injection pump. The fuel rail pressure relief valve is located in the rear of the left common rail. The return fuel travels to the fuel cooler and then to the fuel tank. This fuel is used to cool and lubricate the injection pump and the injectors. DIAGNOSTIC AIDS The following conditions may cause an air leak into the fuel supply system: Deformed or cut O-rings at the fuel supply line connections Improperly seated fuel supply line fittings Porous or weathered rubber fuel supply lines

2000 Dodge RAM 1500 Van Fuel Pressure Leak Down Test

0

Filed Under (Dodge) by admin on 04-05-2011

download
Use this test in conjunction with the Fuel Pump Pressure Test and Fuel Pump Capacity Test. Check Valve Operation: The electric fuel pump outlet contains a one-way check valve to prevent fuel flow back into the tank and to maintain fuel supply line pressure (engine warm) when pump is not operational. It is also used to keep the fuel supply line full of gasoline when pump is not operational. After the vehicle has cooled down, fuel pressure may drop to 0 psi (cold fluid contracts), but liquid gasoline will remain in fuel supply line between the check valve and fuel injectors. Fuel pressure that has dropped to 0 psi on a cooled down vehicle (engine OFF) is a normal condition. When the electric fuel pump is activated, fuel pressure should immediately (1 – 2 seconds) rise to specification. Abnormally long periods of cranking to restart a hot engine that has been shut down for a short period of time may be caused by: Fuel pressure bleeding past a fuel injector(s). Fuel pressure bleeding past the check valve in the fuel pump module. 1. Disconnect the fuel inlet line at fuel rail. Refer to Fuel Tubes/Lines/Hoses and Clamps for procedures. On some engines, air cleaner housing removal may be necessary before fuel line disconnection. 2. Obtain correct Fuel Line Pressure Test Adapter Tool Hose. Tool number 6539 is used for 5/16″ fuel lines and tool number 6631 is used for 3/8″ fuel lines. Fig.7 Connecting Adapter Tool (Typical) 3. Connect correct Fuel Line Pressure Test Adapter Tool Hose between disconnected fuel line and fuel rail (Fig. 7). 4. Connect the 0 – 414 kPa (0 – 60 psi) fuel pressure test gauge (from Gauge Set 5069) to the test port on the appropriate Adaptor Tool. The DRB III Scan Tool along with the PEP module, the 500 psi pressure transducer, and the transducer-to-test port adapter may also be used in place of the fuel pressure gauge. The fittings on both tools must be in good condition and free from any small leaks before performing the proceeding test. 5. Start engine and bring to normal operating temperature. 6. Observe test gauge. Normal operating pressure should be 339 kpa ±34 kPa (49.2 psi ±5 psi) . 7. Shut engine OFF. 8. Pressure should not fall below 30 psi for five minutes . 9. If pressure falls below 30 psi , it must be determined if a fuel injector, the check valve within the fuel pump module, or a fuel tube/line is leaking. 10. Again, start engine and bring to normal operating temperature. 11. Shut engine OFF. 12. Testing for fuel injector or fuel rail leakage: Clamp OFF the rubber hose portion of Adaptor Tool between the fuel rail and the test port “T” on Adapter Tool. If pressure now holds at or above 30 psi , a fuel injector or the fuel rail is leaking.

Related entry:

location of diagnostic port 2005 jaguar, toyota camryhow to test fuel pressure, suzuki 2005 aerio fuel pump relay testing, location of fuel pressure regulator 06 nissan altima 2 5lt, 2006 kia sorento fuel pressure test port, kia fuel pressure test adapter, check fuel pressure 2007 kia sedona, 5 4 triton engine fuel pressure test, 2006 nissan altima fuel pressure check, where do you check the fuel pressure on a nissan altima 2006,