audi a6 2000
You are searching repair manual in PDF format about audi a6 2000 use another keyword for search another post or files
audi a6 2000 Direct Download speed 5787 Kb/s
audi a6 2000 Full Version speed 6767 Kb/s
Filed Under (Audi) by admin on 15-09-2009
Check the following wire connection for open circuit according to wiring diagram:Relay carrier in E-box, plenum chamber, position 3Terminal Harness connector atignition coils Terminal 8 1 Specified value: Wire resistance max 1.5 – If necessary, repair wire connection. Audi A4 Sedan 2002-2004, Audi A4 Avant 2002-2004, Audi A4 Cabriolet 2003-2004 – 1.8 Liter 4-Cyl. 5V Turbo Generic Scan Tool, Engi…Page 5 24-158 If no malfunctions are found in wires: – Check voltage supply of Motronic Engine Control Module (ECM) voltage supply relay – J271 – Page 24-158 . – Check activation of Motronic Engine Control
Module (ECM) voltage supply relay – J271 – Page 24-159 . Checking voltage supply If specified value is not obtained:
- Connect multimeter for voltage measurement as follows. Relay carrier in E-box, plenum chamber, position 3
Filed Under (Audi) by admin on 11-06-2010
2000 Audi A4 Quattro 2.8L, Vin H, Eng 2000 Audi A6 Quattro 2.8L, Vin H, Eng Cfg V6, Eng Des ATQ, USA/Canada Cfg V6, Eng Des ATQ Potential Causes: Engine Mechanical — Mechanical fault causing lack of closed loop operation (vacuum leak/low fuel pressure). Oxygen (O2) Sensors Defective Thermostat Tech Tips: If engine is running too cold, the oxygen sensors will not be enabled by powertrain control module and the allowed time to run the monitor for oxygen sensors will expire, setting the DTC with no other specific fault with the oxygen sensor. 3. If there is no voltage then test for voltage between terminal 1 of the vehicle harness and vehicle ground. Specification with the vehicle running is battery voltage. If voltage specified is not obtained then check the wiring from terminal 1 to the fuel pump relay using available wiring diagrams. 4. If voltage is as specified then test voltage between the vehicle harness terminal 2 and battery positive. Specification with the vehicle running is battery voltage. If specified voltage is not obtained then inspect the wiring between the O2 harness terminal 2 and Engine Control Module (ECM) terminal 5 for open circuit.
Filed Under (Audi) by admin on 03-10-2009
Audi A6 Electrical Wiring Manual: 1998-2000 covers Audi A6 models built on the “C5″ platform through model year 2000. This manual has been prepared us- ing factory wiring diagrams, electrical component location information and scantool diagnostics. Whether you’re a professional service technician or a do-it-your- self Audi owner this manual will be indispensable as a source of the same detailed electrical system information available at an authorized Audi dealer
A6 Sedan 1998, 1999, 2000 A6 Avant 1999, 2000 allroad quattro 2000
Filed Under (Audi) by admin on 25-05-2010
1. With the ignition switch in the OFF position, press and hold button A whilst turning the key to the ON position. 2. The message “Service OIL” will appear. If the message does not display, repeat step 1. 3. Pull out the button B until the message is extinguished. 4. The display should now show “Service —”, indicating that the SRI has been reset.
Audi Manual Service Reset – Audi A4 and A6 (1995 – 1999)
Filed Under (Audi) by admin on 24-05-2010
GEAR BOX CONTROL UNIT MODELS AFFECTED: Audi V8 from ’91 & A8 from ’94 FAULT: 018 gearbox the ATF cooler pipe connection leaks at gearbox. CAUSE: The ATF cooler pipe vibrates this causes the pipe adapter at the gear box to leak. SOLUTION: Do not replace control unit. It is possible to code with VAG 1551 with a workshop
code smaller than 655 36.