axle nut size for chevy venture


You are searching repair manual in PDF format about axle nut size for chevy venture use another keyword for search another post or files



  axle nut size for chevy venture Direct Download speed 5787 Kb/s

  axle nut size for chevy venture Full Version speed 6767 Kb/s




1997 Oldsmobile Bravada Axle Shaft Assembly: Service and Repair Drive Axle Installation FRONT DRIVE AXLE

0

Filed Under (Oldsmobile) by admin on 18-08-2010

download
INSTALL OR CONNECT It is essential that the differential carrier, axle seals are not lubricated or damaged during this process. Prior to drive axle installation, cover the shock mounting bracket, lower control arm bail stud, and all other sharp edges with a shop towel so as not to damage the boot. 1. Axle shaft to differential carrier. With both hands on the tripot housing, align the splines on the shaft with the differential carrier. Then center the drive axle into the differential carrier seal and firmly push the shaft straight into the differential carrier until the snap ring seats into place. NOTICE: Be careful that the safety stand does not damage or bend any components it may contact. 2. Raise the safety stand to support the weight of the lower control arm. Important: It will be necessary to slightly start the knuckle onto the drive axle while simultaneously guiding the lower ball stud to its proper 1997 Oldsmobile Truck Bravada V6-4.3L VIN W location on the steering knuckle. 3. Assemble the lower ball joint. 4. Lower shock mount. 5. Upper ball joint. 6. Drive axle washer and nut. 7. Drive axle nut. – Tighten bolts to 140 Nm (103 ft. lbs.). 8. 9. 10. 11. 12. ABS Bracket located on the top of the upper control arm ball joint. Brackets from upper control arm holding both the ABS wire and brake hose. Caliper and rotor. Tires and wheel. Remove safety stands.

Related entry:

how tight should a axel nut be on a chevy uplander, 2004 ford explorer rear axle nut size, 2004 ford escape axle nut, yhs-synd1, isuzu axiom front axle desamble, 2002 gmc envoy axle but size, 97 camry bolt inboard axel, tools required to remove drive axles hub nut on 2001 Toyota Rav 4, pinion arm 1996 chevy k 1500, 2006 mazda 3 axle nut torque specs,

2005 Chevy Suburban Front Axle Will Not Disengage

0

Filed Under (Chevrolet) by admin on 30-10-2010

download
Front Axle Will Not Disengage Circuit Description The front axle control circuit consists of an electric motor actuator which engages and disengages the front axle. The front axle actuator motor consists of a permanent magnetic motor, a worm gear controlled plunger, a front axle switch and an electronic control circuit all within the actuator assembly. The front axle actuator consists of the following circuits: The front axle control circuit, which is also connected to the transfer case shift control module The front axle switch circuit, which is also connected to the transfer case shift control module A battery feed circuit A ground circuit When a shift to AUTO 4WD, 4HI or 4LO is requested, the transfer case shift control module engages the front axle by grounding the front axle control circuit through a current limiting driver. Diagnostic Aids A mechanical condition inside the front axle could prevent the shift fork from moving causing the motor to be stuck in one position. Refer to Symptoms – Front Drive Axle See: Differential Assembly\Testing and Inspection\Symptom Related Diagnostic Procedures\Diagnosis By Symptom – Front Drive Axle\- Symptoms – Front Drive Axle

Related entry:

1998 chevy 1500 truck front transaxle stuck will not disengage, hub assembly nut size 2005 chevy venture, how to replace pinion bearing on 97 cavalier, how to replace 04 tundra fromt axel actuator, front axle for a 2005 chevy colorado diagram, diagram on axle tube on 2005 chevy colorado, diagram of front axle&wheel of 2005 chevy trailblazer, diagram of axle tube replacement on 2005 chevy colorado, 2004 tundra front differential actuator, what is a pinion bearing on a 97 cavalier,

2004 Ford F-150 Rear Axle Differential Cover Axle Shaft Oil Seal and Rear Wheel Bearing REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 28-02-2011

download
1. With the vehicle in NEUTRAL, position on a hoist. For additional information, refer to Section 100-00. 2. Remove the rear wheel and tire assembly. For additional information, refer to Section 204-00. 3. Remove the parts in the order indicated in the following illustration and table. 4. To install, reverse the removal procedure. 5. Fill the axle with the specified quantity of the specified lubricant. For additional information, refer to the Specifications in this section. Item 2: Rear Disc Brake Caliper Removal Note 1. CAUTION: Do not allow the caliper to hang from the brake hose. Provide a suitable support. Position the rear disc brake caliper aside. For additional information, refer to Section 206-00. Item 7: Differential Pinion Shaft Removal Note 1. Move the differential pinion shaft out far enough to remove the U-washers. Replace the shaft and install the lock bolt finger tight when U-washers are removed. Item 8: U-washer Removal Note 1. CAUTION: Do not damage the rubber O-rings in the axle shaft grooves. Remove the U-washers. 1. Push the axle shafts inboard. 2. Remove the U-washers. Item 10 and 11: Wheel Bearing Oil Seal and Axle Shaft Bearing Removal Note 1. CAUTION: Never remove the wheel bearing oil seal by itself. Always remove the wheel bearing oil seal and the rear wheel bearing at the same time. For the 8.8 inch rear axle, use the special tools to remove the rear wheel bearing and wheel bearing oil seal. 2. CAUTION: Never remove the wheel bearing oil seal by itself. Always remove the wheel bearing oil seal and the rear wheel bearing at the same time. For the 9.75 inch and the 10.25 inch rear axles, use the special tools to remove the rear wheel bearing and wheel bearing oil seal. Item 11: Axle Shaft Bearing Installation Note 1. For the 8.8 inch and the 9.75 inch rear axles, use the special tools to install the rear axle wheel bearing. 2. For the 10.25 inch rear axle, use the special tools shown to install the rear axle wheel bearing. Item 10: Wheel Bearing Oil Seal Installation Note 1. Use the special tools shown to install the rear wheel bearing oil seal. Item 8: U-washer Installation Note 1. CAUTION: Do not damage the rubber O-rings in the U-washer grooves. Install the U-washers. 1. Position the two U-washers on the button end of the axle shafts. 2. Pull the axle shafts outward.

Related entry:

diagram of the rear traction of dodge grand caravan awd 3 8, 2002 ford explorer rear differential diagram, differential for 2005 lincoln aviator, 2007 kia sportage rear hub removal, replace hub on 2007 equinox, diagram for 2008 ford F-150 8 8 rearend, 1999 rodeo wheel seal change schematic, 2003 explorer rear cv removal, 2005 kia sorento drive mid shaft bearing replacement procedure, pictures of how to remove rear wheel bearings from 2003 suzuki xl7,

1996 Pontiac Bonneville Axle Shaft Assembly: Service and Repair FRONT DRIVE AXLE

0

Filed Under (Pontiac) by admin on 11-08-2010

download
1. Raise and support vehicle, then remove tire and wheel assembly. 2. Install a brass drift or a screwdriver to prevent the rotor from turning, Fig. 7 . 3. Remove axle nut and washer. 4. Remove stabilizer shaft or link from control arm. 5. Remove nut from ball joint, then separate ball joint from steering knuckle using separator tool No. J-36226, or equivalent. 6. Remove drive axle from hub and bearing assembly using front hub spindle remover tool No. J-28733-A, or equivalent, Fig. 8 . 7. Remove drive axle from transaxle using axle shaft remover puller tool Nos. J-33008, J-29794 and slide hammer tool No. J-2619-01, or equivalents, if necessary, Fig. 9 . INSTALLATION 1. Install drive axle into the transaxle using seal protector J-37292-B, or equivalent 2. Seat snap ring by placing a screwdriver into the groove on the joint housing and tapping until seated, Fig. 9 . 3. Grasp the inner housing and pull outward. If the snap ring is properly seated, the axle will remain in place. 4. Install drive axle into hub and bearing assembly. 5. Install lower ball joint to steering knuckle and tighten to specifications. 6. Install stabilizer shaft or link to control arm, tighten to specifications. 7. Insert a screwdriver or drift into caliper and rotor to prevent rotor from turning, Fig. 7 . 8. Install new hub nut and washer, tighten to specification. 9. Install tire and wheel assembly, then lower vehicle

Related entry:

axle nut torque 2003 boneville, pontiac montana axle torque, torque specs on the front drive axle of a 2000 Bonneville,

2003 Ford F-150 Front Drive Axle and Differential Exploded View

0

Filed Under (Ford) by admin on 30-03-2011

download
The axle housing assembly consists of a cast-aluminum center section, a removable cast-aluminum axle housing tube (3B210), and a differential housing cover (3N136). Both the axle housing tube and the differential housing cover use silicone sealant as a gasket. The hypoid-design gearset consists of an 8.8-inch ring gear (3A397) and a pinion gear (3N175). Two opposed tapered roller bearings support the drive pinion in the axle housing. A drive pinion collapsible spacer (4662), located on the pinion shaft, maintains pinion bearing preload. The pinion nut adjusts the preload. Differential bearing shims (4A451), located between the differential bearing cups (4221) and the axle housing, adjust the differential bearing preload and the ring gear backlash. The differential case (4205) is a one-piece design with two openings to allow for assembly of the internal components and lubricant flow. Two opposed tapered roller bearings (differential bearings [4221]) support the differential case in the axle housing. Removable differential bearing caps (4224) retain the differential assembly in the axle housing. Inside the differential case, the differential pinion shaft (4211) supports two differential pinion gears (4215). The pinion gears engage the differential side gears (4236), to which the left axle shaft (3A381) and the axle cluster gear shaft (7L253) are splined. The differential pinion shaft bolt retains the differential pinion shaft in the differential case. An embossed metal tag, bolted to the rear face of the RH axle tube, contains front axle identification information. CAUTION: Actuate the front drive axle with the wheels in a straight ahead position, and at light throttle only. A front axle actuator motor assembly (7G360), controlled by an instrument panel-mounted switch, actuates the front drive axle.

Related entry:

99 chevy blazer front differential, differential spezialisten vw touareg, 2000chevrolet blazer s10 front differential noise, front diff case halves sealant for trailblazer, lexus differential exploded veiw, diagram chevy s10 front differential, 1998 jaguar xjr differential, 1996 suburban front differential pics, chevy s10 differential repair, chrysler 9 25 differential exploded view,