bmw e46 relay layout
You are searching repair manual in PDF format about bmw e46 relay layout use another keyword for search another post or files
bmw e46 relay layout Direct Download speed 5787 Kb/s
bmw e46 relay layout Full Version speed 6767 Kb/s
Filed Under (volkswagen) by admin on 05-11-2010
Relay location on the thirteen position auxiliary relay panel, above relay panel: 1 – Auxiliary Emergency Flasher Relay (404) 2 – Relay for Motor Remote Unlock Rear Lid (79) 3 – Starting Interlock Relay (53) (185) (465) 4 – Fog Light Relay (53) 5 – Control Module for Multi-function Steering Wheel (450) 6 – Control Module for Multi-function Steering Wheel (450) 7 – Daytime Running Lights Change-over Relay (173), from April 1999 8 – Daytime Running Lights Change-over Relay (173), through March 1999 9 – Dual Horn Auxiliary Relay (53) 10 – Glow Plug Relay (180) 10 – Warning Lamp Auxiliary Relay (200) 11 – Park/Neutral Position (PNP) Relay (175) 12 – Power Supply (Terminal 30, B+) Relay (109) Relay Panel: 1 – Dual Horn Relay (53) 2 – Load Reduction Relay (18) (100) 4 – Fuel Pump (FP) Relay (409) V – Wiper/Washer Intermittent Relay (192) (377) (389) VI – Wiper/Washer Intermittent Relay (192) (377) (389) NOTE Number in parentheses ( ) indicates production control number stamped on relay housing.
Filed Under (Dodge) by admin on 07-12-2010
1. Remove fuel pump relay from power distribution center at driver’s side front corner of engine compartment, near the battery. Note terminal identification on fuel pump relay. See Fig. 6 . 2. To check fuel pump relay resistance, use ohmmeter and check resistance between terminals No. 85 and 86 on fuel pump relay. Replace fuel pump relay if resistance is not 70-80 ohms. 3. To check fuel pump relay operation, connect ohmmeter between terminals No. 30 and 87A on fuel pump relay. See Fig. 6 . Ohmmeter should indicate continuity between terminals No. 30 and 87A on fuel pump relay. 4. Connect ohmmeter between terminals No. 30 and 87 on fuel pump relay. See Fig. 6 . Ohmmeter should indicate no continuity between terminals No. 30 and 87 on fuel pump relay. CAUTION: DO NOT allow ohmmeter leads to contact terminals No. 85 and 86 on fuel pump relay when fuel pump relay is energized. 5. Connect 16-gauge jumper wire between negative battery terminal and terminal No. 85 on fuel pump relay. Connect 16-gauge jumper wire between positive battery terminal and terminal No. 86 on fuel pump relay. 6. Fuel pump relay should now be energized. No continuity should now exist between terminals No. 30 and 87A on fuel pump relay. Continuity should now exist between terminals No. 30 and 87 on fuel pump relay. Disconnect jumper wires. Replace fuel pump relay if defective. 7. If fuel pump relay or wiring circuit failure exists, a Diagnostic Trouble Code (DTC) will be stored in Powertrain Control Module (PCM). See appropriate G – TESTS W/CODES article.
Filed Under (Volvo) by admin on 07-08-2010
No. 1/1 2/1 2/2 2/4 2/5 2/6 2/7 2/11 2/15 2/16 2/17 2/20 2/22 2/23 2/28 2/30 2/32 2/35 2/44 2/46 2/53 2/61 2/66 3/1 3/2 3/3 3/4 3/6 3/7 Component Name Battery Headlight relay with bulb failure sensor Foglight relay Intermittent wiper relay, windshield wipers Relay, seat belt reminder/ignition key warning Overload relay 15I Central lock relay, inside lighting, delayed action Relay, engine cooling fan Relay exhaust temperature sensor Intermittent wiper relay, tailgate wiper Horn relay Relay auto down power windows Automatic climate control A/C relay Relay, fuel pump Anti-theft relay Overload relay, +X Main relay, Fuel Injection system Start motor 50 relay Relay rear window/door mirror heating Relay ignition coil Air pump relay Parking lights relay Relay, fog lights, USA Ignition lock High and low beam switch Switch, turnsignal/high-low beam Cruise control operation Switch, hazard warning with flasher relay Foglight switch
Filed Under (Jaguar) by admin on 20-11-2010
R1 R2 R3 R4 R5 R6 R7 R8 R9 R10 R11 WINDSHIELD WIPER MOTOR RELAY WINDSHIELD HEATER RELAY HORN RELAY ACCESSORY POWER RELAY POWER WASH PUMP RELAY A/C COMPRESSOR CLUTCH RELAY EMS CONTROL RELAY TCM RELAY DIP BEAM RELAY STARTER RELAY THROTTLE MOTOR RELAY R15 R16 R17 R18 R19 R20 R21 MAIN BEAM / FRONT FOG RELAY NOT USED REVERSE LAMPS RELAY IGNITION RELAY HEATED REAR WINDOW RELAY A/C BLOWER RELAY BATTERY SAVER RELAY
Filed Under (Honda) by admin on 11-12-2010
FUEL SYSTEM PRESSURE RELEASE NOTE: 1. Loosen fuel tank filler cap to relieve tank pressure. Remove fuel pump relay from underhood fuse/relay box. Start and operate engine until it stalls. Crank engine an additional 30 seconds. 2. Loosen hose clamp of fuel line on side of pressure regulator, coming from fuel line inlet distributor pipe. Cover fuel hose with a shop towel, and slowly pull hose from pressure regulator to relieve fuel pressure. When fuel stops leaking, reinstall hose and clamp. FUEL PRESSURE & FUEL PUMP RELAY TEST NOTE: Fuel Pressure 1. Relieve fuel pressure. See FUEL SYSTEM PRESSURE RELEASE . Attach Fuel Pressure Gauge Set (J-34730-1 ) and Adapter (J-35957-1 ) to Schrader fitting on fuel rail. Disconnect pressure regulator vacuum hose. Turn ignition on. Allow fuel pump to run for about 2 seconds. 2. Fuel system pressure should be about 41-46 psi (2.8-3.2 kg/cm2 ). See FUEL PUMP PERFORMANCE . Start engine and check for leaks. Connect pressure regulator vacuum hose. If engine will not start, the fuel pump relay can be by-passed. Also see appropriate CHART A-3 – ENGINE CRANKS BUT WILL NOT RUN under TROUBLE SHOOTING CHARTS. With engine idling, fuel pressure should be 25-30 psi (1.8-2.1 kg/cm2 ). NOTE: Fuel pump relay is located in engine compartment fuse/relay box. Begin basic fuel system diagnosis with testing fuel pressure. To test the fuel pump relay circuit, proceed to CHART A-5 – FUEL PUMP RELAY CIRCUIT under TROUBLE SHOOTING CHARTS. Fuel Pump Relay 1. ECM supplies power to relay as long as ECM receives ignition reference signals or starter crank signal. To run fuel pump without starting engine, remove relay and jumper terminals No. 2 and 4. See Fig. 5 and Fig. 6 . 2. To test relay, use jumper wires to ground terminal No. 4 of relay and apply battery voltage to terminal No. 2 of relay. Using ohmmeter, check for continuity between relay terminals No. 1 and 3. If continuity is not present, replace relay.