bmw s62 oil gallery diagram


You are searching repair manual in PDF format about bmw s62 oil gallery diagram use another keyword for search another post or files



  bmw s62 oil gallery diagram Direct Download speed 5787 Kb/s

  bmw s62 oil gallery diagram Full Version speed 6767 Kb/s




2003 Buick Century Engine Oil and Oil Filter Replacement Removal Procedure

0

Filed Under (Buick) by admin on 15-12-2010

download
1. 2. 3. 4. 5. Raise and support the vehicle. Refer to Vehicle Lifting. Position the oil drain pan under the engine oil drain plug. Remove the engine oil drain plug. Clean and inspect the engine oil drain plug, repair or replace if necessary. Clean and inspect the engine oil drain plug sealing surface on the oil pan, repair or replace oil pan if necessary. 6. Remove the oil filter. 7. Clean and inspect the oil filter sealing area on the engine block, repair or replace if necessary. Installation Procedure 1. Lightly oil the replacement oil filter gasket with clean oil and install the new oil filter. Notice: Refer to Fastener Notice in Service Precautions. 2. Install the new oil filter. Tighten the new oil filter to 3/4 to 1 full turn, after the oil filter gasket contacts the oil filter mounting surface. 3. Install the engine oil drain plug. Tighten the plug to 30 Nm (22 ft. lbs.) . 4. 5. 6. 7. 8. 9. Remove the oil drain pan. Lower the vehicle. Fill the engine with new engine oil. Start the engine. Inspect for oil leaks after engine start up. Turn off the engine and allow the oil a few minutes to drain back into the oil pan. Remove the oil level indicator from the oil level indicator tube. Clean off the indicator end of the oil level indicator with a clean paper towel or cloth. Install the oil level indicator into the oil level indicator tube until the oil level indicator handle contacts the top of the oil level indicator tube. Again, remove the oil level indicator from the oil level indicator tube keeping the tip of the oil level indicator down. Check the level of the engine oil on the oil level indicator. If necessary, adjust the oil level by adding or draining the engine oil. 10. 11. 12. 13. 14. 15.

Related entry:

removing transmission sump filter seal 2011 ram 6 7, automotive compressor capacities, outlet oil cooler line replacement, where is opl sensing unit for 2000 chrysler crown victoria, how to remove a clio sump pan, gwhere is oil filter on F150 2004 diagramogle, installation procedure for iol cooler blazer, chrysler balancer shaft 2 4 install, oil pressure sending unit 2007 chevy uplander, 2008 ford 5 4 triton oil pump removal,

Oil Filter Cap Assembly Precautions

0

Filed Under (Toyota) by admin on 20-05-2011

download
To prevent damage to the oil ?lter cap assembly, this procedure must be closely followed during oil ?lter replacement to avoid immediate and future oil ?lter serviceability concerns. The following engines are equipped with a plastic oil ?lter cap assembly: • 1UR-FE (Tundra, Sequoia) • 3UR-FE (Tundra, Sequoia, Land Cruiser) • 2ZR-FE (Corolla, Matrix) • 1AR-FE (Highlander, Venza) • 2AR-FE (RAV4, Camry) Repair Procedure NOTICE During oil ?lter replacement: • Ensure that SST 09228-06500-02 or 09228-06501 is used to remove and install the oil ?lter cap — or damage to the cap may occur. • Inspect the SST for any damage or distortion before use. • Con?rm that the SST is fully seated on the oil ?lter cap when removing/installing (see Figure 1). Figure 1. 1 3 4 1 2 3 4 • Ensure a torque wrench is used for oil ?lter cap installation. Torque: 25 +/- 5 N*m (255 +/- 51 kgf*cm, 18 +/- 3.7 ft*lbf) • There is a possibility the oil ?lter cap will be dif?cult to remove if the torque range is exceeded. FAILURE TO FOLLOW THE INSTRUCTIONS ABOVE MAY RESULT IN OIL FILTER CAP AND/OR SST DAMAGE. With Drain Plug Without Drain Plug Oil Filter Cap SST (09228-06500-02 or 09228-06501) Refer to the Technical Information System (TIS) when replacing the oil ?lter, applicable model and model year Repair Manual: • 2010 Camry: Engine/Hybrid System – Lubrication – “2AR-FE Lubrication: Oil and Oil Filter: Replacement” • 2009 / 2010 Corolla: Engine/Hybrid System – Lubrication – “2ZR-FE Lubrication: Oil and Oil Filter: Replacement” • 2009 Highlander: Engine/Hybrid System – Lubrication – “1AR-FE Lubrication: Oil and Oil Filter: Replacement” • 2008 / 2009 Land Cruiser: Engine/Hybrid System – Lubrication – “3UR-FE Lubrication: Oil and Oil Filter: Replacement” • 2009 / 2010 Matrix: Engine/Hybrid System – Lubrication – “2ZR-FE Lubrication: Oil and Oil Filter: Replacement” • 2009 RAV4: Engine/Hybrid System – Lubrication – “2AR-FE Lubrication: Oil and Oil Filter: Replacement” • 2008 / 2009 / 2010 Sequoia (3UR-FE): Engine/Hybrid System – Lubrication – “3UR-FE Lubrication: Oil and Oil Filter: Replacement” • 2010 Sequoia (1UR-FE): Engine/Hybrid System – Lubrication – “1UR-FE Lubrication: Oil and Oil Filter: Replacement” • 2007 / 2008 / 2009 / 2010 Tundra (3UR-FE): Engine/Hybrid System – Lubrication – “3UR-FE Lubrication: Oil and Oil Filter: Replacement” • 2010 Tundra (1UR-FE): Engine/Hybrid System – Lubrication – “1UR-FE Lubrication: Oil and Oil Filter: Replacement” • 2009 Venza: Engine/Hybrid System – Lubrication – “1AR-FE Lubrication: Oil and Oil Filter: Replacement”

Related entry:

17k707, 17k707 replacement, honda frv oil sensor, dmax lubrication points, chassis lube 02 ml500, change pollen filter on corsa d, 4GR-FSE OIL FILTER, 2000 toyota tacoma instuctions for lubricating chassis, 1997 chevy 1500 ac oil replacement, 1993 chevy cavalier upper intake manifold assy,

2003 Saturn ION Engine Oil and Oil Filter Replacement Removal Procedure

0

Filed Under (Saturn) by admin on 18-08-2010

download
1. Raise and support the vehicle. 2. Place a drain pan under the oil drain plug. 3. Remove the oil pan drain plug. Important: DO NOT use an open end wrench on the hex on top of the oil filter cap. 4. Use a 32 mm (1 1/4 inch) socket on the hex on the top of the oil filter cap, or an oil filter wrench on the outside diameter of the oil filter cap. 5. Remove the oil filter cap with filter. 6. Remove the filter from the cap. Installation Procedure 1. Install the filter to the cap. 2. Install the oil filter cap with filter. Notice: Over torquing the oil filter cap may cause damage to the oil filter cap resulting in an oil leak. Notice: Refer to Fastener Notice in Service Precautions. Important: DO NOT use an open end wrench on the hex on top of the oil filter cap. 3. Use a 32 mm (1 1/4 inch) socket on the hex on the top of the oil filter cap, or an oil filter wrench on the outside diameter of the oil filter cap. – Tighten the oil filter cap until fully seated, DO NOT exceed 25 Nm (18 ft. lbs.). 4. Install the oil pan drain plug. – Tighten the oil pan drain plug to 25 Nm (18 ft. lbs.). 5. Lower the vehicle. 6. Fill the engine with oil

Related entry:

1996 cougar oil leak, 2005 saturn ion manual transmission filter?, 2010 kia soul ccv filter, honda pp-to40x,

2004 Honda Element EX ROCKER ARM OIL PRESSURE SWITCH (VTEC OIL PRESSURE SWITCH)

0

Filed Under (Honda) by admin on 21-12-2010

download
1. Check the engine oil level. Is the level OK? YES- Go to step 2 . NO- Adjust the engine oil to the proper level, then go to step 14 . 2. Turn the ignition switch ON (II). 3. Clear the DTC with the HDS. 4. Do the VTEC TEST in the INSPECTION MENU with the HDS. Is the result OK? YES- Intermittent failure, system is OK at this time. Check for poor connections or loose terminals at the rocker arm oil pressure switch (VTEC oil pressure switch) and the ECM/PCM. NO- Go to step 5 . 5. Check the result of step 4 . Rocker Arm Oil Pressure Switch (VTEC Oil Pressure Switch) Failure Rocker Arm Oil Pressure Switch (VTEC Oil Pressure Switch) Open Rocker Arm Oil Pressure Switch (VTEC Oil Pressure Switch) SIG Line Open Rocker Arm Oil Pressure Switch (VTEC Oil Pressure Switch) GND Line Open Is the test result any of the above? YES- Go to step 6 . NO- Check for poor connections or loose terminals at the rocker arm oil pressure switch (VTEC oil pressure switch). If it is OK, replace the rocker arm oil control solenoid (VTEC solenoid valve) (see step CMP SENSOR A REPLACEMENT ), then go to 14 . 6. Turn the ignition switch OFF. 7. Disconnect the rocker arm oil pressure switch (VTEC oil pressure switch) 2P connector. 8. Check for continuity between rocker arm oil pressure switch (VTEC oil pressure switch) 2P connector terminals No. 1 and No. 2.

Related entry:

wiring diagram for headlight switch1995 Dodge Dakota, What are the torque specks for rocker arm assembly 2004 Chrysler Pacifica, broken headlight switch on a 1990 chevrolet 1500, 1999 chrysler lhs ignition wiring diagram, how to replace switch interruptor 2007 chevy silverado, valet switch 1996 honda odyssey, ignition lock cylinder for 2000 malibu, jeep switch commutateur, 95 dodge dakota disconnect headlight switch diiagram, low oil pressure 2003 malibu,

1983 BMW 733i Engine Oil Requirements and Specifications

0

Filed Under (BMW) by admin on 06-06-2010

download
A. Approved Engine Oils ^ For BMW gasoline engines all single grade and multiple grade, heavy duty (HD) engine oils* according to API classification: SE or SF. ^ For BMW turbocharged diesel engines all single grade and multiple grade, heavy duty (HD) engine oils* according to API classification: CD. ^ For BMW gasoline and diesel engines all single grade and multiple grade engine oils* according to API classification: SE/CD or SF/CD. *Engine oil may be either a mineral or synthetic base. ^ Special Oils: Because of their special viscosity/temperature properties, these engine oils can be used for outside temperatures from -22~F to 86~F (-30~C to + 30~C). Mo SAE 5W-30 is the only motor oil that has been tested and approved by BMW as a special oil. However, since special oils have friction reducing properties and consequen influence the break-in behavior of engines, they should not be used until after the initial 1200 mile break-in period. ^ SAE viscosity classes according to BMW standards conforming with normally predominating outside temperatures – see BMW temperature/viscosity table. B. Engine Oil Change Intervals The first oil change with oil filler replacement is scheduled for the break-in inspection at 1200 miles. Other Oil Changes ^ For cars with Service Indicator: when “OIL SERVICE” or “INSPECTION” display comes on, including oil filter.