buick allure, how to change left rear signal bulb


You are searching repair manual in PDF format about buick allure, how to change left rear signal bulb use another keyword for search another post or files



  buick allure, how to change left rear signal bulb Direct Download speed 5787 Kb/s

  buick allure, how to change left rear signal bulb Full Version speed 6767 Kb/s




2003 Jeep Liberty Rear Lamp Bulb Replacement

0

Filed Under (Jeep) by admin on 27-07-2010

download
REMOVAL The rear lamp unit may contain up to four bulbs, depending upon the market for which the vehicle was manufactured. The service procedures for each bulb is the same, only the bulb sizes and types may differ. Be certain any removed bulb is replaced with the same bulb size and type that was removed. 1. Disconnect and isolate the battery negative cable. 2. Remove the rear lamp unit from the end of the quarter panel. (Refer to LAMPS/ LIGHTING – EXTERIOR/REAR LAMP UNIT – REMOVAL). 3. Firmly grasp the socket on the socket plate at the back of the rear lamp unit housing for the bulb that is being removed (Fig. 59). 4. Rotate the socket on the socket plate at the back of the rear lamp unit housing counterclockwise about 30 degrees . 5. Pull the socket and bulb straight out of the back of the rear lamp unit housing. 6. Pull the bulb straight out of the rear lamp unit socket. INSTALLATION CAUTION: Always use the correct bulb size and type for replacement. An incorrect bulb size or type may overheat and cause damage to the lamp, the socket andlor the lamp wiring. 1. Align the base of the bulb with the receptacle in the rear lamp unit socket. 2. Push the bulb straight into the rear lamp unit socket until it is firmly seated. 3. Align the socket and bulb with the opening in the socket plate on the back of the rear lamp unit housing (Fig. 59). 4. Push the socket and bulb straight into the rear lamp unit housing until the socket is firmly seated against the socket plate. 5. Rotate the socket on the socket plate at the back of the rear lamp unit housing clockwise about 30 degrees . 6. Reinstall the rear lamp unit onto the end of the quarter panel. (Refer to LAMPS/ LIGHTING – EXTERIOR/REAR LAMP UNIT – INSTALLATION). 7. Reconnect the battery negative cable.

Related entry:

how to change low beam headlight on 2006 toyota tarago, 2003 mercury mountaineer replacing tail light and turn sig nal bulbs, how to change cigarette lighter socket 2010 SILVERADO, how to remove accessory socket from chevy 2002 silverado, how to replace a dome light jeep liberty, how to replace rear turn signal on 2004 f150, pto UNIT-mazda, rear turn signal on 2003 mountaineer, replace rear turn signal lamp 2004 ford 150, replacing running light bulb in 2007 edcalade,

R34 Nissan Skyline ECU pin outs

0

Filed Under (Nissan) by admin on 17-05-2011

download
Terminal number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 (CHK) 23 24 (IGN) 25 26 27 28 29 30 31 32 *33 *34 *35 36 37 *38 39 *40 *41 42 43 44 45 46 47 48 49 50 51 Description Ign signal (power transistor) Cyl #1 Ign signal (power transistor) Cyl #5 Ign signal (power transistor) Cyl #3 ECM & IGN coil relay control signal Tachometer drive signal – Ign signal (power transistor) Cyl #6 Ign signal (power transistor) Cyl #2 Ign signal (power transistor) Cyl #4 – AAC valve control signal – Fuel pump relay control signal Air conditioner control signal – - Malfunction indicator lamp – - Ignition switch (START) signal Air conditioner switch signal Check (Diagnosis start) Throttle position sensor signal Ignition switch (IGN) signal Control unit ground Power steering oil pressure switch signal – SB (select bit) 1 signal [RB25DET A/T] Vehicle speed sensor signal (Vehicle speed sensor 2) Headlamp switch signal; Ignition power supply Control unit ground Idle position switch signal “1″ position switch signal “2″ position switch signal – Throttle opening signal [RB25DE-4WD M/T, RB25DE A/T, RB25DET] “0″ position switch signal Neutral signal (Park/neutral position signal) “R” position switch signal Full switch signal – Sensor ground Crankshaft position sensor 120? (REF) signal Crankshaft position sensor 120? (REF) signal Crankshaft position sensor 1? (POS) signal Ring gear crankshaft position sensor signal [RB20DE (L/B)] Turbo pressure sensor signal [RB25DET] Power supply for throttle position sensor, refrigerant pressure sensor, and turbo pressure sensor Rear defogger switch signal Heated oxygen sensor signal Fuel pump terminal voltage control output signal [RB25DET] Injector No. 6 cylinder drive signal Line pressure solenoid valve control signal (Dropping resistor Throttle motor sensor signal [RB25DET] *113 circuit)

Related entry:

location of flasher for a 1999 dodge intrepid es, f450 turn signal relay locater, 1980 datsun pickup signal light fuse location, turn signal relay 2006 kia optima, TURN SIGNAL RELAY 1994 bonneville, spi line 2001 dodge ram 1500 failed ecm, location of flasher on 2003 oldsmobile alero, Jeep j-54 doors and top, free diagram 1993 ranger fuel injectors, flasher assembly for 2003 alero,

1995 Ford Thunderbird Spring REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 02-03-2011

download
Removal 1. Raise vehicle on hoist. Refer to Section 00-02. 2. Remove rear wheel and tire assembly. 3. Remove rear stabilizer bar link and bushing link nuts at both ends of rear stabilizer bar (5A772) . Rotate bar up and out of the way. 4. Disconnect parking brake rear cable and conduit (2A635) at rear disc brake caliper (2553) . 5. Install three Rotunda Spring Cages 086-00031 or equivalent to rear spring as follows: a. Install one spring cage without an adjuster link to the inboard side (the innermost “bend” of the rear spring (5560) ). b. Install two more spring cages, with adjusters, at 120 degree angles to the previously installed cage. Spring, Rear 6. Place a transmission jack or suitable stand under the rear suspension arm and bushing (5500) as far outboard as possible. 7. Support the rear wheel knuckle (5A969) assembly by wiring the rear suspension arm and bushing to the body. 8. Remove lower rear shock absorber mounting bolt, washer and nut. 9. NOTE: Rear suspension arm and bushing must not be lowered until pivot bolts are loose. Do not attempt to remove plastic cap on front pivot nut. Loosen both inboard pivot bolts on rear suspension arm and bushing . 10. Remove two bolts and nuts retaining rear suspension arm and bushing to rear wheel knuckle . 11. Lower the rear suspension arm and bushing by lowering jack. Ensure spring cages properly seat on rear spring as rear suspension arm and bushing is dropped. 12. Remove jack, lower rear suspension arm and bushing down fully by hand and remove rear spring with cages in place. 13. Remove rear spring center mounting insulators (5741) , if necessary. 14. If spring cages are to be removed for installation on rear spring , use Coil Spring Compressor D78P-5310-A or equivalent to compress rear spring and remove cages. Rear spring center mounting insulator should be installed on rear spring before installing rear spring in tool to prevent slipping of plates.

Related entry:

2004 Ford Explorer Differential Diagram, blow up diagrams of 2002 ford E150 rear axle, BMW X5 Rear Suspension Diagram, step by step instruction on how to change struts on 1995 740i BMW?, diagram of dodge hatch lock, diagram Caliper slider on vauxhall vectra, 2002 Tahoe rear AC Diagram, replace rear abs sensor 2007 jeep compass, 2008 jeep patriot rear drum breaks disassembly, install knuckle bushing buick,

2004 Ford F-150 Rear Axle Differential Cover Axle Shaft Oil Seal and Rear Wheel Bearing REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 28-02-2011

download
1. With the vehicle in NEUTRAL, position on a hoist. For additional information, refer to Section 100-00. 2. Remove the rear wheel and tire assembly. For additional information, refer to Section 204-00. 3. Remove the parts in the order indicated in the following illustration and table. 4. To install, reverse the removal procedure. 5. Fill the axle with the specified quantity of the specified lubricant. For additional information, refer to the Specifications in this section. Item 2: Rear Disc Brake Caliper Removal Note 1. CAUTION: Do not allow the caliper to hang from the brake hose. Provide a suitable support. Position the rear disc brake caliper aside. For additional information, refer to Section 206-00. Item 7: Differential Pinion Shaft Removal Note 1. Move the differential pinion shaft out far enough to remove the U-washers. Replace the shaft and install the lock bolt finger tight when U-washers are removed. Item 8: U-washer Removal Note 1. CAUTION: Do not damage the rubber O-rings in the axle shaft grooves. Remove the U-washers. 1. Push the axle shafts inboard. 2. Remove the U-washers. Item 10 and 11: Wheel Bearing Oil Seal and Axle Shaft Bearing Removal Note 1. CAUTION: Never remove the wheel bearing oil seal by itself. Always remove the wheel bearing oil seal and the rear wheel bearing at the same time. For the 8.8 inch rear axle, use the special tools to remove the rear wheel bearing and wheel bearing oil seal. 2. CAUTION: Never remove the wheel bearing oil seal by itself. Always remove the wheel bearing oil seal and the rear wheel bearing at the same time. For the 9.75 inch and the 10.25 inch rear axles, use the special tools to remove the rear wheel bearing and wheel bearing oil seal. Item 11: Axle Shaft Bearing Installation Note 1. For the 8.8 inch and the 9.75 inch rear axles, use the special tools to install the rear axle wheel bearing. 2. For the 10.25 inch rear axle, use the special tools shown to install the rear axle wheel bearing. Item 10: Wheel Bearing Oil Seal Installation Note 1. Use the special tools shown to install the rear wheel bearing oil seal. Item 8: U-washer Installation Note 1. CAUTION: Do not damage the rubber O-rings in the U-washer grooves. Install the U-washers. 1. Position the two U-washers on the button end of the axle shafts. 2. Pull the axle shafts outward.

Related entry:

tourch on rear wheel bearing on a 2010 chevy impala, 2004 ford explorer rear differential diagram, 2007 acadia rear blower removal, how to remove rear axle shaft of mitsubishi strada triton, balance shaft seal for 2004 honda acccord 4 cylinder schematic, 2004 expedition right axle tube seals, 2004 ford escape rear gears, 2006 suzuki forenza front wheel drive axle diagram, 2008 chevy silverado cv axle nut size, changing 33mm center hub nut on landrover freelander,

2010 Toyota Prius Rear Brake Squeak

0

Filed Under (Toyota) by admin on 09-05-2011

download
Introduction Some 2010 Prius vehicles may experience rear brake squeak when backing up or moving forward during the ?rst few brake applications when the brakes are cold. An updated rear brake shim kit is available to reduce the likelihood of this condition occurring. Repair Procedure 1. Test drive the vehicle to con?rm the squeak is coming from the rear brakes. The condition occurs more frequently when backing up during light brake pedal application after cold soak. 2. Remove rear brake shims. Refer to the Technical Information System (TIS) 2010 Prius Repair Manual: Brake – Brake (Rear) Brake: Rear Brake: Removal 3. Clean the rear brake pad backing plates with a clean shop towel and apply a small amount of black disc brake grease to the backing plate of each rear brake pad. NOTE Make sure disc brake grease is not applied to the lining of the rear brake pads. 4. Install the No. 1 Anti-squeal shims. Install the No. 2 Anti-squeal shims. Figure 3. 5. Using the Variable Pin Wrench (SST 09960-10010), slowly rotate the caliper piston until the piston groove is positioned as shown in the illustration below. 6. Install new rear brake anti-squeal shims with brake pads into the rear caliper assemblies brackets. Refer to (TIS), 2010 Prius Repair Manual: Brake – Brake (Rear) Brake: Rear Brake: Installation NOTE • When installing the rear disc brake caliper assembly on the rear disc brake caliper mounting bracket, ensure the protrusion on the brake pad is centered in the caliper piston groove. • It is important to ensure the protrusion is not contacting the outer edges of the caliper piston groove. (both sides) 7. Road test the vehicle to con?rm the condition has been reduced.

Related entry:

2006 toyota corolla rear brake shoe removel, change pads rotors 2008 camry, rear break diagram of 2009 chevy aveo, why rear brakes grab on 04 freestar, 2003 ford escape brake shoe replacement guide, rear brake caliper bracket on 2005 mazda 6, install rear drum brakes 2006 chevy silverado, change roters 2008 camry, rear brake saturn opel diagram, diagram of rear drum brake on 2002 suzuki xl7,