cavalier sub frame alignment holes


You are searching repair manual in PDF format about cavalier sub frame alignment holes use another keyword for search another post or files



  cavalier sub frame alignment holes Direct Download speed 5787 Kb/s

  cavalier sub frame alignment holes Full Version speed 6767 Kb/s




2003 Ford Windstar Camber and Caster Adjustment

0

Filed Under (Ford) by admin on 24-10-2010

download
All Vehicles 1. Using a 19 mm (0.76 inch) dowel, check the front sub-frame alignment. The dowel should slide directly through the front sub-frame and body without tilting. Vehicles Requiring Front Sub-Frame Alignment 2. Loosen the four bolts. 3. Align the front sub-frame to the correct position. The dowel should slide directly through the front sub-frame and body without tilting. Tighten the four bolts. 5. Recheck the camber and caster measurements. Follow the manufacturer’s instructions. Adjust the camber and caster as necessary. On a correctly aligned front sub-frame, the RH caster will lead the LH caster by 0.5 degrees. Vehicles Requiring Camber and Caster Adjustment 6. Remove the cowl top vent panel. 7. Center punch the four spot welds. 8. Loosen the nuts. 9. CAUTION: Do not cut deeper than necessary to remove the alignment plate. Using the special tool, remove the four spot welds. 10. Remove the nuts and the alignment elate. 11. Prepare the shock tower and alignment plate surfaces. Remove any burrs. Clean and paint any exposed metal. 12. Position the alignment plate. Loosely install the nuts. 13. Adjust the camber and caster. 14. Tighten the nuts. 15. Check the alignment settings. Follow the manufacturer’s instructions. Readjust the camber and caster as necessary. 16. CAUTION: Do not drill deeper than 9.6 mm (0.38 inch) into the shock tower. Drill three 3.2 mm (0.12 inch) holes through the alignment plate and shock tower. Clean and paint any exposed metal. 17. Install three pop rivets. Use 3.2 mm (0.12 inch) diameter x 6.4 mm (0.25 inch) grip range steel pop rivets. 18. Install the cowl top vent panel.

Related entry:

2005 trailblazer front end alignment, how to adjust the rear camber on a 2002 saturn l200, 04 trailblazer how to adjust caster, afjust camber on awindstar, camber adjustment chevy venture, camber caddy, howo adjust caster on a cavalier, mitsubishi triton 2wd camber adjustment, rear camber adjustment 2005 malibu,

1999 Chevrolet Blazer WHEEL ALIGNMENT PROCEDURES

0

Filed Under (Chevrolet) by admin on 21-01-2011

download
PRE-ALIGNMENT CHECKS Ensure steering wheel is centered and front wheels are in straight-ahead position (to correct, shorten one tie rod adjusting sleeve and lengthen the opposite sleeve in equal amounts). Ensure none of the following conditions exist: Incorrect vehicle ride height (see RIDE HEIGHT ). Incorrect tire pressure, mismatched tires (differing size or type), excessive tire runout, unbalanced tire and wheel assemblies, loose wheel bearings, or loose wheel lug nuts. Loose or worn steering linkage/suspension components, or excessive play in steering gear box. CAMBER & CASTER ADJUSTMENT “C”, “G” & “K” Series Except 1999 Sierra & Silverado C1500 & C2500 (Caster Adjustment) 1. Check frame angle. See “C”, “G”, “K” & “P” (FRAME ANGLE) . If corrected caster is not within specification, remove frame bracket slots. See “C”, “G” & “K” SERIES (FRAME BRACKET SLOT REMOVAL) . Reset caster by loosening nut on end of each cam bolt securing upper control arm to frame brackets. See Fig. 18 . 2. Rotate cam bolts until caster is within specification. See WHEEL ALIGNMENT SPECIFICATIONS table. Tighten nuts to specification. See TORQUE SPECIFICATIONS table.

Related entry:

1999 malibu front wheel bearing repacking, 1999 BLAZER shift linkage, 1999 chevy blazer alignment specs, 1999 Chevy blazer dashboard removal, alignment specification for 1999 ranger, removing the dash on a 1999 chevy blazer,

1999 Ford Taurus Steering Gear Base REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 19-02-2011

download
1. Open hood. 2. Disconnect battery ground cable (14301). Refer to Section 14-01. 3. From inside vehicle, remove nuts retaining steering column tube boot (3C611) to cowl panel. 4. Remove bolt retaining steering column intermediate shaft coupling (3A525) to steering column lower yoke (3N725) . 5. Position steering column tube boot out of the way. Remove pinch bolt retaining steering column intermediate shaft coupling to power rack and pinion steering gear and remove steering column intermediate shaft coupling . 6. Raise vehicle on a twin post hoist and remove front wheel and tire assemblies. 7. Remove exhaust system flex tube-to-dual converter Y-pipe attachment. Disconnect heated oxygen sensor wiring harness. Remove dual converter Y pipe (5F250) from vehicle. Dual Converter Y Pipe Removal 8. Support vehicle with jack stands under rear edge of front sub-frame (5C145). 9. Remove tie rod cotter pins and nuts, and remove tie rod end (3A130) from RH front wheel knuckle (3K185) and LH front wheel knuckle (3K186). 10. Remove tie rod end from front wheel spindle tie rod (3280) . Mark position of jam nut to maintain alignment. 11. Remove nuts from steering gear-to-front sub-frame retaining bolts. 12. Remove rear sub-frame-to-body retaining bolts. 13. Raise twin post hoist carefully until rear sub-frame (5R003) separates from body approximately 102 mm (4 inches). 14. Remove heat shield push-pin retainers from power steering hose bracket (3C510). Remove steering shaft U-joint shield (3F540). 15. Remove screw and power steering left turn pressure hose (3A714) from power steering hose bracket . Remove two screws and power steering hose bracket. 16. Remove LH stabilizer bar link (5K484). 17. Disconnect power steering pressure switch electrical connector. 18. Rotate power rack and pinion steering gear to clear bolts from front sub-frame and pull left to ease line fitting removal. 19. Place a drain pan under vehicle and remove hydraulic power steering pressure hose and power steering return hose from fittings on power rack and pinion steering gear. 20. Remove power rack and pinion steering gear assembly through LH wheel well. Installation 1. Install new Teflon® O-rings on both line connector assemblies as described under Quick Connect Power Steering Fitting—Seal Replacement. 2. Place steering gear retaining bolts in steering gear housing (3548). 3. Install power rack and pinion steering gear through LH wheel well. 4. Install power steering hose bracket and two screws. Tighten to 9-12 Nm (80-106 lb-in). 5. Install hydraulic power steering pressure hose and power steering return hose to fittings on power rack and pinion steering gear. Tighten hoses to 33-41 Nm (25-30 lb-ft). 6. Install power steering pressure hose and and screw. Tighten to 9-12 Nm (80-106 lb-in). 7. Connect power steering pressure switch electrical connector. 8. Position power rack and pinion steering gear into front sub-frame. 9. Install tie rod ends onto front wheel spindle tie rods . 10. Install push-pin retainers at top of heat shield. 11. Install tie rod end to RHfront wheel knuckle and LH front wheel knuckle. Install nuts and tighten to 47-63 Nm (35-46 lb-ft). Install new cotter pins. 12. Install LH stabilizer bar link. Tighten to 76.5-103.5 Nm (57-76 lb-ft).

Related entry:

can u remove third row power seat chrysler town and country, remove and replace steering intermediate shaft 2003 buick regal, 06 pt cruiser rack and pinion replacement procedure, wiring diagram opel corsa steering rack, video on changing the rack and pinion on a ford taurus, the steering rod that controls the front tires came off the ball at the wheel axel how do I replace it on a yard machine riding mower, replacing the steering rack on a 2003 ford ranger, how to remove rack and pinion on a 2000 lincoln continental, how to remove corsa C steering rack, how to disconnect the Steering column intermediate shaft on 2000 lincoln continental,

1995 Ford Contour Hoses Pressure and Return REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 15-02-2011

download
Removal 1. Disconnect battery ground cable. 2. Disconnect power steering pressure (PSP) switch electrical connector. 3. Remove power steering pressure (PSP) switch from power steering pressure hose. 4. On 2.0L engine, remove one nut, two bolts and disconnect power steering pressure hose from power steering pump bracket and engine lifting bracket. 5. On 2.5L engine, remove one bolt and disconnect power steering pressure hose from front engine support insulator. 6. Remove power steering pump auxiliary reservoir as outlined. 7. Raise vehicle on hoist. Refer to Section 00-02. 8. Remove front sub-frame. Refer to Section 02-01. 9. Remove six bolts and steering gear cover plate from front sub-frame. 10. Disconnect power steering pressure hose and power steering return hose unions from steering gear. 11. Remove two bolts retaining power steering pressure and return hoses to front sub-frame and remove power steering pressure and return hoses. CAUTION: Whenever the power steering pressure and return hoses and/or steering gear are disconnected, the power steering pressure and return hoses and/or steering gear should be plugged to prevent system contamination. If the power steering system becomes contaminated with dirt or other foreign matter, power steering pump and/or steering gear failure may result. Installation 1. Position power steering pressure and return hoses to front sub-frame and secure with two bolts. Tighten bolts to 28 Nm (21 lb-ft). 2. Connect power steering pressure hose and power steering return hose unions to steering gear. Tighten unions to 31 Nm (23 lb-ft). 3. Install steering gear cover plate and secure with six bolts. Tighten bolts to 50 Nm (37 lb-ft). 4. Install front sub-frame. Refer to Section 02-01. 5. Lower vehicle. 6. Install power steering pump auxiliary reservoir as outlined. 7. On 2.5L engine, connect power steering pressure hose to front engine suppor t insulator and secure with one bolt. Tighten bolt to 6 Nm (53 lb-in). 8. On 2.0L engine, connect power steering pressure hose to power steering pump bracket and engine lifting bracket. Secure with one nut and two bolts. Tighten nut and bolts to 6 Nm (53 lb-in). 9. Install power steering pressure (PSP) switch into power steering pressure hose. 10. Connect power steering pressure (PSP) switch electrical connector. 11. Connect battery ground cable. 12. Refill power steering fluid as necessary and bleed system. Refer to Section 11-00. Hose Fittings, Pressure and Return Line at Steering Gear and Pump

Related entry:

diagram of 2001 ford winstar power steering line, 2004 neon power steering return line, how to replace power steering pump 2004 maxda tribute, 2006 fusion power steering pump removal, 2008 ford f150 power steering pump, location to replace a rack and pinion on a 2007 Hyundai Tucson se, how to cahnge power steering belt on 2002 echo, how to adjust a power steering belt 2002 toyota echo, ford mondeo power steering fluid cooling coil, e350 power distribution box,

2005–2006 Toyota Tacoma CLUTCH PEDAL SQUEAK NOISE

0

Filed Under (Toyota) by admin on 04-06-2011

download
Some customers may complain about a “squeak” or “creak” noise when depressing or releasing the clutch pedal. The clutch master cylinder clevis assembly has been improved to eliminate this condition. Repair Procedure 1. Record all radio presets before starting. 2. Disconnect the negative (–) battery terminal cable. 3. Remove the clutch pedal sub–assembly. A. Remove the front door opening trim LH (scuff plate). B. Remove the cowl side trim board. C. Remove the instrument panel finish panel lower No. 1. D. Remove the driver’s side Junction Block. E. Remove the turnover (compression) spring. F. Remove the bolt attached to the instrument panel reinforcement assembly. G. Remove the clutch pedal sub–assembly. a. Remove the bolt and nut. b. Remove the clutch pedal from the clutch pedal support. 4. Remove the clutch pedal spring holder from the clutch pedal support. 5. Remove the clutch pedal pad. 6. Remove the two (2) clutch pedal bushes from the clutch pedal. 7. Remove the clutch pedal shaft collar. 8. Using needle–nose pliers, remove the No. 1 cushion from the clutch pedal. 9. Install the clutch pedal No. 1 cushion on the NEW clutch pedal sub–assembly. NOTE: Install parts on the NEW clutch pedal sub–assembly BEFORE installing in the vehicle. 10. Install the clutch pedal shaft collar. A. Apply MP grease to the clutch pedal shaft collar. B. Install the clutch pedal shaft collar onto the clutch pedal. 11. Install the clutch pedal bushes. A. Apply MP grease to the two (2) NEW bushes. B. Install the two (2) bushes onto the clutch pedal. 12. Install the clutch pedal pad. 13. Install the clutch pedal spring holder. A. Apply MP grease to the contact surface of the clutch pedal spring holder. B. Install the clutch pedal spring holder. 14. Remove the clevis sub–assembly. A. Measure length “A” of the clutch master cylinder. a. Measure length “A” between the lock nut and the thread end with a ruler. b. Record length “A”. B. Remove the clevis sub–assembly from the master cylinder. a. Loosen the lock nut. b. Rotate and remove the clevis sub–assembly. 15. Install the NEW clevis sub–assembly. A. Rotate the lock nut to match length “A”. B. Rotate and install the NEW clevis sub–assembly to contact the lock nut. C. Tighten the lock nut and torque to specification. Torque: 11.8 NSm (120 kgfScm, 8.7 ftSlbf) D. Apply MP grease to the ball end of the clevis sub–assembly where it will contact the clutch pedal. 16. Install the NEW clutch pedal sub–assembly. A. Install the clutch pedal onto the clutch support with the bolt and nut. Torque: 34 NSm (347 kgfScm, 25 ftSlbf) HINT: Install the bolt from the left side of the vehicle. B. Apply MP grease to the clutch pedal sub–assembly where the clevis sub–assembly contacts the clutch pedal. NOTE: Failure to apply grease to the clevis and clutch pedal sub–assemblies could cause the noise to return. C. Tighten the bolt to the instrument panel reinforcement assembly. Torque: 8 NSm (82 kgfScm, 6 ftSlbf) 17. Install the turnover (compression) spring. A. Apply MP grease to the contact surface of the spring holder, clutch pedal, and spring. B. Install the spring onto the clutch pedal and spring holder.

Related entry:

1994 mazda b3000 how to replace clutch and slave free download, ford mondeo 2003 clutch cable, 2005 kia sorento bleed the cluch, What is the APP Position Sensor in 2008 Kia Sorento?, 92 chevy clutch clutch pivot ball adjustment, changing clutch on 2006 kia sorento, how to clutch change 99 vw beetle, bleeding clutch system fj40, how to install ac clutch on 2002 ford f150 4 6, 2003 trail blazer air conditioner pump replacement,