changing rear drum brakes on 2000 chevy venture


You are searching repair manual in PDF format about changing rear drum brakes on 2000 chevy venture use another keyword for search another post or files



  changing rear drum brakes on 2000 chevy venture Direct Download speed 5787 Kb/s

  changing rear drum brakes on 2000 chevy venture Full Version speed 6767 Kb/s




2002 Ford Ranger Brakes – Rear Brakes Grabbing Condition

0

Filed Under (Ford) by admin on 08-11-2010

download
Some vehicles may exhibit a grabbing condition from the rear brakes during the first few brake applications. The condition only occurs after the vehicle has been parked for several hours. ACTION Follow the Service Procedure steps to correct the condition. SERVICE PROCEDURE To service, reduce/minimize moisture intrusion into the rear drum brake assemblies by applying Motorcraft® Silicone Gasket and Sealant to the brake backing plate. 1. Place vehicle on hoist and remove the rear wheels. 2. Remove the rear brake drums and replace the rear linings. Refer to Workshop Manual (WSM), Section 206-02. WARNING Do not breathe dust or use compressed air to blow dust from storage containers or friction components. Remove dust using government-approved techniques. Friction component dust may be a cancer and lung disease hazard. Exposure to potentially hazardous components may occur if dusts are created during repair of friction components, such as brake pads and clutch discs. Exposure may also cause irritation to skin, eyes and respiratory tract, and may cause allergic reactions and/or may lead to other chronic health effects. If irritation persists, seek medical attention or advice. Failure to follow these instructions may result in serious personal injury. 3. Inspect the rear brake assemblies for damaged, missing and/or improperly seated adjuster plug or parking brake cable. 4. Inspect and clean the lining contact area of the brake drum; machine if necessary. 5. Reinstall the rear brake drums and adjust the lining to drum clearance per WSM, Section 206-02. 6. Thoroughly clean the backside of the rear drum brake backing plate to promote proper adhesion of sealant. 7. Apply Motorcraft(R) Silicone Gasket and Sealant to the backside of the rear drum brake backing plate at the following inter[ace areas (Figure 1): ^ Axle Flange ^ Wheel Cylinder ^ Parking Brake Cable ^ Hold Down Pins NOTE AVOID GETTING SEALANT ON THE BRAKE BLEED SCREW AND BRAKE TUBE NUT. 8. Reinstall the rear wheels and torque lug nuts per Workshop Manual, Section 204-04.

Related entry:

exploded view of rear brakes 2005 dodge grand caravan, chrysler town and country 2005 right left brake schematic, changing rear brakes on a 2005 town and country mini van, 1989 mercury back brakes exploded view, exploded view of brake cylinder for 1996 K1500, exploded view of 2010 nissan versa rear druim, 2001 toyota rav how to change rear drum brakes, 2002 ford escape rear brake change, remove rear brake drums 2002 chev venture, replace rear drum brakes on mazda tribute 2004,

2000 Ford F-150 Parking Brake Rear Drum Brakes

0

Filed Under (Ford) by admin on 02-02-2011

download
Remote release handle Parking brake control Parking brake rear cable and conduit clip (part of 2A635) Parking brake cable bracket Parking brake rear cable and conduit— (LH) Parking brake rear cable and conduit— (RH) Parking brake cable equalizer Front parking brake cable and conduit Front parking brake cable clip The parking brake system is actuated when the parking brake control (2780) is depressed. The parking brake control applies tension to the front parking brake cable and conduit (2853) and parking brake cable equalizer (2A602). The parking brake cable equalizer is coupled to the RH parking brake rear cable and conduit (2A635) and the LH parking brake rear cable and conduit. The respective rear brake assemblies are then applied. The rear wheel brake assembly contains a cable-actuated parking brake assembly. The parking brake releases the rear brakes using a remote release lever incorporated with the parking brake control. If the parking brake control is not fully released, the parking brake signal switch will illuminate the brake warning light. The parking brake signal switch is mounted on the parking brake control. The switch is held in place by a self-tapping screw and aligned with a locater pin. The drum brake parking brake system is self-adjusting, therefore cable tension does not need to be adjusted. Rear Disc Brakes Parking Brake Components, Rear Disc Brakes

Related entry:

2004 chevy trailblazer front brake diagram, tacoma brakes diagram, honda accord 2008 brake caliper torque spec, rear brake line diagram 2004 kia sorento, sprinter rear brake diagram, diagram of the brake shoe of a mercury milan, how to install brake switch on 2007 chev 1500, Diagram 2003 Toyota Highlander AWD Emergency Parking Brakes, adjusting parking brake rav4, repair parking brake Hyundai Tusan,

1995 Ford Thunderbird Spring REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 02-03-2011

download
Removal 1. Raise vehicle on hoist. Refer to Section 00-02. 2. Remove rear wheel and tire assembly. 3. Remove rear stabilizer bar link and bushing link nuts at both ends of rear stabilizer bar (5A772) . Rotate bar up and out of the way. 4. Disconnect parking brake rear cable and conduit (2A635) at rear disc brake caliper (2553) . 5. Install three Rotunda Spring Cages 086-00031 or equivalent to rear spring as follows: a. Install one spring cage without an adjuster link to the inboard side (the innermost “bend” of the rear spring (5560) ). b. Install two more spring cages, with adjusters, at 120 degree angles to the previously installed cage. Spring, Rear 6. Place a transmission jack or suitable stand under the rear suspension arm and bushing (5500) as far outboard as possible. 7. Support the rear wheel knuckle (5A969) assembly by wiring the rear suspension arm and bushing to the body. 8. Remove lower rear shock absorber mounting bolt, washer and nut. 9. NOTE: Rear suspension arm and bushing must not be lowered until pivot bolts are loose. Do not attempt to remove plastic cap on front pivot nut. Loosen both inboard pivot bolts on rear suspension arm and bushing . 10. Remove two bolts and nuts retaining rear suspension arm and bushing to rear wheel knuckle . 11. Lower the rear suspension arm and bushing by lowering jack. Ensure spring cages properly seat on rear spring as rear suspension arm and bushing is dropped. 12. Remove jack, lower rear suspension arm and bushing down fully by hand and remove rear spring with cages in place. 13. Remove rear spring center mounting insulators (5741) , if necessary. 14. If spring cages are to be removed for installation on rear spring , use Coil Spring Compressor D78P-5310-A or equivalent to compress rear spring and remove cages. Rear spring center mounting insulator should be installed on rear spring before installing rear spring in tool to prevent slipping of plates.

Related entry:

2004 Ford Explorer Differential Diagram, saturn outlook hatch will not open, schematic drawing of 2002 ford explorer rear suspension, exploded view of 1888 corvette rear hub assembly, D40 differential diagrams, peugeot 206 rear axle trailing arm removal tool, how to replace the rear interear lighr on 1998 vw passat, how change struts on a 1995 bmw 740il, 2004 rear differential diagram, replacing rear shocks absorber buick rendez vous 2005,

2006 Honda Civic Rear ABS Wheel Speed Sensor and O-Ring Inspection

0

Filed Under (Honda) by admin on 10-01-2011

download
During assembly, some wheel speed sensors may have been improperly installed and do not seal the hub assembly. Water may enter the hub assembly and damage the wheel bearing. In areas where road salt is used, the wheel bearings may corrode, which may cause the wheel to separate and fall off, increasing the risk of a crash. CORRECTIVE ACTION Inspect both rear ABS wheel speed sensors and their O-rings. If an ABS wheel speed sensor or O-ring is damaged, replace the damaged part and the hub bearing unit on that wheel. REPAIR PROCEDURE 1. 2. 3. 4. Raise the vehicle on a lift. Remove the rear wheels. Remove both rear ABS wheel speed sensors. Inspect the rear ABS wheel speed sensors and their O-rings. • If a rear ABS wheel speed sensor O-ring is damaged (cut, torn, pinched, or flattened), replace the O-ring and the corresponding rear hub bearing unit, then go to step 5. DAMAGED O-RINGS: O-ring is pinched. • If the rear ABS wheel speed sensor tip has any physical damage, remove the original sensor assembly, replace the corresponding rear hub bearing unit(s), and connect the new sensor’s wire harness. Then go to step 5. – Refer to page 18-34 (with disc brakes) or 18-36 (with drum brakes) of the 2006–07 Civic Service Manual, or – Online, enter keyword HUB, then select Rear Knuckle/Hub Bearing Unit Replacement from the list. O-ring is rolled out of the groove and flattened. -Refer to page 18-34 (with disc brakes) or 18-36 (with drum brakes) of the 2006–07 Civic Service Manual, or – Online, enter keyword HUB, then select Rear Knuckle/Hub Bearing Unit Replacement from the list. • If the rear ABS wheel speed sensors and their O-rings are OK, go to step 5. 5. Lubricate the ABS wheel speed sensor O-ring and the sensor hole in the knuckle with multi-purpose grease.

Related entry:

Diagram of the speed sensor on a 2007 chevy equinox, 2006 escape wheel sensor ring replace, Rear Hub Assembly Diagram, 2005 explorer rear abs sensor, avalanche rear speed sensor, bj5p crank sensor, 2008 lincoln mkx abs sensor ring, how to change front wheelhub assassembly on 07 hyundai santa fe all wheel drive, ford F250 reluctor ring, how to replace a rear hub on a chevy equinox,

2004 Ford F-150 Rear Axle Differential Cover Axle Shaft Oil Seal and Rear Wheel Bearing REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 28-02-2011

download
1. With the vehicle in NEUTRAL, position on a hoist. For additional information, refer to Section 100-00. 2. Remove the rear wheel and tire assembly. For additional information, refer to Section 204-00. 3. Remove the parts in the order indicated in the following illustration and table. 4. To install, reverse the removal procedure. 5. Fill the axle with the specified quantity of the specified lubricant. For additional information, refer to the Specifications in this section. Item 2: Rear Disc Brake Caliper Removal Note 1. CAUTION: Do not allow the caliper to hang from the brake hose. Provide a suitable support. Position the rear disc brake caliper aside. For additional information, refer to Section 206-00. Item 7: Differential Pinion Shaft Removal Note 1. Move the differential pinion shaft out far enough to remove the U-washers. Replace the shaft and install the lock bolt finger tight when U-washers are removed. Item 8: U-washer Removal Note 1. CAUTION: Do not damage the rubber O-rings in the axle shaft grooves. Remove the U-washers. 1. Push the axle shafts inboard. 2. Remove the U-washers. Item 10 and 11: Wheel Bearing Oil Seal and Axle Shaft Bearing Removal Note 1. CAUTION: Never remove the wheel bearing oil seal by itself. Always remove the wheel bearing oil seal and the rear wheel bearing at the same time. For the 8.8 inch rear axle, use the special tools to remove the rear wheel bearing and wheel bearing oil seal. 2. CAUTION: Never remove the wheel bearing oil seal by itself. Always remove the wheel bearing oil seal and the rear wheel bearing at the same time. For the 9.75 inch and the 10.25 inch rear axles, use the special tools to remove the rear wheel bearing and wheel bearing oil seal. Item 11: Axle Shaft Bearing Installation Note 1. For the 8.8 inch and the 9.75 inch rear axles, use the special tools to install the rear axle wheel bearing. 2. For the 10.25 inch rear axle, use the special tools shown to install the rear axle wheel bearing. Item 10: Wheel Bearing Oil Seal Installation Note 1. Use the special tools shown to install the rear wheel bearing oil seal. Item 8: U-washer Installation Note 1. CAUTION: Do not damage the rubber O-rings in the U-washer grooves. Install the U-washers. 1. Position the two U-washers on the button end of the axle shafts. 2. Pull the axle shafts outward.

Related entry:

diagram of the rear traction of dodge grand caravan awd 3 8, 2004 ford explorer rear differential diagram, replace hub on 2007 equinox, 1999 rodeo wheel seal change schematic, 2005 kia sorento drive mid shaft bearing replacement procedure, 2002 ford explorer rear differential diagram, pictures of how to remove rear wheel bearings from 2003 suzuki xl7, 2003 explorer rear cv removal, diagram for 2008 ford F-150 8 8 rearend, 2007 kia sportage rear hub removal,