chevy tracker vibration


You are searching repair manual in PDF format about chevy tracker vibration use another keyword for search another post or files



  chevy tracker vibration Direct Download speed 5787 Kb/s

  chevy tracker vibration Full Version speed 6767 Kb/s




1990 Ford Bronco Full Size Driveline Vibration Testing

0

Filed Under (Ford) by admin on 27-01-2011

download
This is a higher-frequency, lower-amplitude vibration than high-speed shake, directly related to road speed, and usually more noticeable at higher road speeds, 72 km/h (45 mph) and up. It is felt in the floor pan or heard as a rumble, hum or boom. It will exist in all drive modes, but may vary somewhat in acceleration, deceleration, float or coast modes. If the vibration is particularly responsive to heavy acceleration or deceleration, especially at lower speeds, driveline angles should be checked. A driveline vibration can usually be duplicated with the axle supported on a hoist or jack stands; through light brake application while accelerating and decelerating, to simulate road load resistance, may be necessary to bring it out. 1. Raise vehicle promptly after road-testing, on twin post hoist or jack stands, to prevent tire flat- spotting. Engage drive train and run-up to observed road test speed to verify presence of vibration. If not evident, check non-driving wheels with wheel-balancer spinner to rule out imbalance as a possible cause. On 4×4′s, unlock front hubs or remove hub covers before spinning wheels. If required, balance non- driving wheels and repeat road test. If vibration is still evident, proceed to driveshaft inspection, Step 3. 2. If vibration appeared in road-speed hoist-test, mark relative position of drive wheels on axle or hub lugs to permit re-installation in original position, and remove wheels. Secure brake drums, if present, by installing all lug nuts in reversed position, and repeat road-speed run-up. If vibration is gone, check drive wheel run-out and balance. If vibration persists, proceed to Step 3.

Related entry:

Saturn 2000 L vibration during acceleration,

2001 Ford Escort ZX2 Engine – Vibration While Idling

0

Filed Under (Ford) by admin on 21-10-2010

download
DRIVEABILITY – IDLE VIBRATION – VEHICLES EQUIPPED WITH 2.0L SPI OR ZETEC ENGINE ONLY ^ ENGINE – IDLE VIBRATION – VEHICLES EQUIPPED WITH 2.0L SPI OR ZETEC ENGINE ONLY ACTION Diagnose and repair idle vibration conditions by referring to the following idle vibration Service Procedures. SERVICE PROCEDURE NOTE THE PROCEDURE CONTAINED IN THIS TSB ARTICLE MAY NOT COMPLETELY ELIMINATE ALL VIBRATION FROM THE VEHICLE. SOME VIBRATION IS INHERENT IN 1-4 ENGINE DESIGNS, SUCH AS THE SPI AND ZETEC 2.0L. THIS PROCEDURE IS DESIGNED TO REDUCE THE AMOUNT OF VIBRATION EXPERIENCED BY THE CUSTOMER. PROCEDURE FOR 2003 ESCORT ZX2 1. Neutralize engine mounts only. Refer to appropriate model year Noise, Vibration and Harshness (NVH) Workshop Manual Section 100-04. PROCEDURES FOR 1997-2002 ESCORT, ESCORT ZX2 AND TRACER 1. Shift the transaxle into Neutral and apply the parking brake. 2. Remove battery and battery tray. 3. Support engine with Three-Bar Engine Support Tool (Rotunda 303-D063) and Lifting Brackets (Rotunda 303-050). 4. Raise vehicle. Refer to the appropriate model year Workshop Manual, Section 100-02. 5. Remove the rear lower cross-member (attached with four (4) bolts (Figure 1)). 6. Remove the engine support cross-member that runs from front to rear of the engine (Belly Band). This can be accomplished by removing the front two (2) attaching bolts, the rear two (2) attaching nuts and the four (4) Engine Mount # 1 and # 2 nuts (Figure 1). NOTE DISCARD THE TWO ENGINE MOUNT # 1 FLAT WASHERS FOR VEHICLES BUILT PRIOR TO 12/03/2001 ONLY. NOTE STEP 7 MODIFICATIONS ARE FOR VEHICLES BUILT PRIOR TO 07/15/02 ONLY. 7. Modify the Belly Band on the two rear attaching Engine Mount # 1 holes by slotting the holes approximately 1/4″ (6 mm) in a front to rear direction. Use a Drill Bit (Figure 7). 8. Loosen the center bolt on the # 1 (rear) lower Engine Mount (Figure 4). 9. Loosen the center bolt on the # 2 (front) lower Engine Mount (Figure 4). NOTE STEP 10 IS FOR VEHICLES BUILT PRIOR TO 05/26/2000 ONLY. 10. Remove original front and rear engine support cross-member bushings (Figure 3).

Related entry:

2002 ford focus vibrating to much how to fix, 2009 ford focus bad vibration while ideling, 16v zetec timing pic, ford focus vibration while idling, ford focus 2005 vibrates, ford f150 vibrating while idoling, ford 2 0 escort engine diagram, engine vibration in daihatsu sirion 2008, diagram of a 2002 ford escort engine, daihatsu sirion ej de simtom of throtle body,

2005 Ford F 250 Wheels/Tires – Steering Wheel Nibble/Vibration

0

Filed Under (Ford) by admin on 20-10-2010

download
VIBRATION DIAGNOSTICS – STEERING WHEEL NIBBLE – TIRE WHEEL RUNOUT AND BALANCE FORD: 2005 Excursion, Explorer Sport Trac 2005-2008 Escape, Expedition, Explorer, F-150, F-Super Duty, Ranger 2006-2008 F-53 Motorhome Chassis 2007-2008 Explorer Sport Trac LINCOLN: 2005-2008 Navigator 2006-2008 Mark LT MERCURY: 2005-2008 Mariner, Mountaineer ISSUE Various Ford, Mercury and Lincoln vehicles may exhibit a vibration / steering wheel nibble above 50 MPH (80 Km/h) which may be associated to a wheel and tire vibration. ACTION Follow the Service Procedure steps to correct the condition. 1. Long term temporary flat spotting can develop when a vehicle is stored without driving. Some initial tire and wheel vibration issues (such as flat spotting) will correct themselves after the tires have been in service for 200 miles (320 km). Confirm vehicle tires have been in service a minimum of 200 miles (320 km) to remove long term temporary flat spotting. Do not continue with this procedure if tires do not meet this requirement. 2. Refer to Workshop Manual (WSM), Section 100-04 to determine if a wheel and tire speed (9-14.5 HZ) vibration is present. a. If the vibration is wheel and tire speed proceed Step 3. b. If not, follow the diagnostics provided in the WSM, Section 100-04.

Related entry:

2005 escape rumbles at idle,

1995 Ford Windstar Engine Front Cover REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 06-04-2011

download
Engine Front Cover If the engine front cover (6019) is being removed to check timing chain deflection, refer to Timing Chain Deflection Procedure as outlined in Section 03-00. SPECIAL SERVICE TOOL(S) REQUIRED Description Crankshaft Damper Remover Vibration Damper and Seal Replacer T82L-6316-A Vibration Damper Remover Adapter Removal 1. Remove engine (6007) from vehicle. Refer to procedure in this section. 2. Loosen drive belt tensioner (6B209) and drive belt (8620) . 3. Remove water pump pulley retaining bolts and water pump pulley (8509) . 4. Remove retaining bolts and disconnect heater water outlet tube (18663) from water pump (8501) . 5. Disconnect electrical connector at camshaft position sensor. 6. Disconnect electrical connector at crankshaft position sensor (CKP sensor) (6C315) . 7. Remove retaining bolt and disconnect radiator lower hose tube (8291) from water pump . NOTE: If the vibration damper and crankshaft pulley have to be separated, mark the vibration damper and crankshaft pulley so that they may be reassembled in the same relative position. This is important as the vibration damper and crankshaft pulley are initially balanced as a unit. NOTE: If the vibration damper is being replaced, check if the original vibration damper has balance pins installed. If so, new balance pins (6A328 or equivalent) must be installed on the new vibration damper in the same position as the original vibration damper. The crankshaft pulley (new or original) must also be installed in the same relative position as originally installed. 8. Remove crankshaft pulley (6312) and vibration damper assembly using Crankshaft Damper Remover T58P-6316-D and Vibration Damper Remover Adapter T82L-6316-B. 9. Remove four retaining bolts and remove brace from A/C bracket and P/S bracket. 10. Remove oil bypass filter (6714) . Tool Number T58P-6316-D T82L-6316-B CAUTION: The engine front cover cannot be removed without lowering the oil pan (6675) . 11. Remove oil pan . Refer to procedure in this section. CAUTION: Do not overlook the engine front cover retaining bolt located behind the oil pump and filter body (6603) . The engine front cover will break if pried upon and all retaining bolts are not removed. 12. Remove engine front cover retaining bolts. It is not necessary to remove water pump . 13. Remove engine front cover and water pump as an assembly. 14. Remove engine front cover gasket and discard. Water Pump Tightening Sequence Installation NOTE: Lightly oil all bolt and stud bolt threads before installation except those specifying special sealant. 1. Clean gasket surfaces on the engine front cover and cylinder block (6010) . If reusing the engine front cover , replace crankshaft front seal (6700) . Refer to Crankshaft Pulley and/or Damper and/or Crankshaft Front Seal in this section. 2. If a new engine front cover is to be installed: Install oil pump and filter body . Clean water pump gasket surface. Position a new water pump housing gasket (8507) on the engine front cover and install water pump . Install water pump retaining bolts. Tighten to 20-30 Nm (15-22 lb-ft). 3. Lubricate crankshaft front seal with clean engine oil XO-10W30-QSP or -DSP or equivalent meeting Ford specification ESE-M2C153-E. NOTE: Gasket and Trim Adhesive D7AZ-19B508-B or equivalent meeting Ford specification ESE-M2G52-A is recommended to hold the engine front cover gasket (6020) in position while the engine front cover is installed. 4. Position a new engine front cover gasket on the cylinder block and install the engine front cover / water pump assembly using dowels for proper alignment. 5. Install the engine front cover retaining bolts. Tighten to 20-30 Nm (15-22 lb-ft). Install the capscrew (Part No. N804841) nearest the oil bypass filter flange last, and tighten last. Apply Loctite® or equivalent to bolt prior to installation. Refer to illustration under Step 13 of removal procedure. 6. Install oil pan as outlined. 7. Install oil bypass filter . 8. Coat pulley sealing surface with clean engine oil XO-10W30-QSP or -DSP or equivalent meeting Ford specification ESE-M2C153-E. NOTE: When using silicone rubber sealer, assembly must occur within 15 minutes after sealer application. After this time, the sealer may start to setup, and its sealing effectiveness may be reduced. 9. Apply a small amount of Silicone Gasket and Sealant F1AZ-19562-A or equivalent meeting Ford specification WSE-M4G320-A2 to crankshaft keyway. 10. Position crankshaft key (6B316) in the crankshaft keyway.

Related entry:

1996 camry valve cover gasket repair, is a g6 engine 2008 the same as a vue engine, lifter erplacement 2004 nissan x tera 3 3 engine, ml320 valve cover remove, pajero rocker box gasket replacement, removing a seal from gearbox at the right side front aixle in opel astra 2 0, removing atf seal gear box for astra 2 0, removing Citroen C5 enginc covers, replace relay 2004 F150 Cam Position Sensor manual, rx 300 valvae cover bolt torque,

2006 Mazda5 BODY VIBRATION AT CRUISE SPEED

0

Filed Under (Mazda) by admin on 16-06-2011

download
DESCRIPTION Some vehicles may experience a body vibration when driving approximately 55mph. This symptom is due to the characteristics of the No. 3 & No. 4 engine mounts. Modified No. 3 & No. 4 engine mounts have been established for service only. Customers having this concern should have their vehicle repaired using the following repair procedure. REPAIR PROCEDURE IMPORTANT NOTE: • This repair should only be performed if all tires and rims are confirmed to be in balance and all suspension components are in proper working condition. • Notify customers that use of the modified mounts will reduce vibration at cruising speed but may increase vibration at idle. NOTE: Because idle vibration may increase, it is highly recommended to continue using mass production mounts for all other service concerns. 1. Verify concern. 2. Replace the No. 3 & 4 engine mounts with service parts according to the appropriate Workshop Manual section 01-10 ENGINE REMOVAL/INSTALLATION. 3. Center the new engine mounts as outlined in ENGINE MOUNT CENTERING PROCEDURE. 4. Verify repair. ENGINE MOUNT CENTERING PROCEDURE No. 1, No. 3 and No. 4 Engine Mount Adjustment 1. Warm up the engine. 2. Raise and support vehicle on a hoist. 3. Remove engine under cover. 4. Lower the vehicle until the front tires lightly touch the ground. 5. Secure the engine and transaxle using an engine jack and attachment as instructed in No.3 Engine Mount And No.4 Engine Mount Rubber Installation Note in appropriate Workshop Manual, section 01-10 MECHANICAL. 6. Remove two bolts from No. 3 engine mount bracket. REMOVE THE BOLTS 7. Lift engine using jack until No.3 engine mount is lifted slightly from vehicle body. NOTE: • Do not raise engine too much or A/C pipe damage may occur. 8. Move the engine mount rubber or engine until installation hole on the vehicle body aligns with hole in the engine mount bracket. ENGINE MOUNT BRACKET 1532c SHOWN BEFORE ALIGNING THE HOLES SHOWN AFTER ALIGNING THE HOLES 9. Lower the jack and tighten bolts on No. 3 engine mount bracket. Tightening torque: 55.0-77.3 ft-lbf (74.5-04.9 N.m) NOTE: 10. With engine supported as described in STEP 5, remove four (4) nuts and two (2) bolts from No. 4 engine mount top plate. Remove top plate. NOTE: 11. Lift engine again using jack until No.4 engine mount is lifted slightly from vehicle body. NOTE: 12. With top plate of No. 4 engine mount removed, move engine mount bottom plate or engine until all four (4) installation studs on the vehicle align with the engine mount holes. • Do not allow the engine mount bracket to be misaligned. • To access the mount, remove battery box. • Do not raise engine too much or A/C pipe damage may occur. ALIGN THE 4 STUDS IN THE PLATE HOLES 13. Place top plate back on and tighten No. 4 engine mount bracket nuts and bolts to torque indicated. Tightening torque: A.32.5-45.0 ft-lbf (44.0-61.0 N.m) B.61.1-86.7 in-lbf (6.9-9.8 N.m) TIGHTEN BOLTS IN SEQUENCE SHOWN 1532e 14. Lift engine again using jack and loosen the two bolts on the No. 1 engine mount rubber until slightly loose on the No. 1 engine mount rubber.

Related entry:

opel corsa 1 3 1997 engine, nissan ka20 engine manual free, 4d35 engine user manual pdf, 93 Ford Ranger Engine Diagram, 2002 dodge ram 1500 4 7 engine vacuum hose diagram, 1999 mercury sable engine diagram, Chevy 454 Engine Manual, isuzu 4hf1 dtc 61, mazda g6 engine specs, toyota tundra forum 5 7 timing chain diagram,