como cambiar el compresor de una kia sedona 2002


You are searching repair manual in PDF format about como cambiar el compresor de una kia sedona 2002 use another keyword for search another post or files



  como cambiar el compresor de una kia sedona 2002 Direct Download speed 5787 Kb/s

  como cambiar el compresor de una kia sedona 2002 Full Version speed 6767 Kb/s




Kia Sorento/ Kia Sedona Throttle Position Sensor W/3.5L Engine

0

Filed Under (KIA) by admin on 04-06-2010

download
Description This bulletin provides information related to the Throttle Position Sensor (TPS) for Sorento & Sedona models. Some Sorento & Sedona vehicles may exhibit diagnostic trouble codes P0121 and/or P1121. This condition mainly occurs in high ambient or desert areas, and can be related to the occasional increase in contact resistance due to excessive wear of the inner elements of the TP sensor. This bulletin describes the proper service and adjustment procedure for replacing the TP Sensor. – Service Procedure Replacement Procedure: 1. Turn ignition OFF. Remove engine cover and disconnect electrical connector from TP Sensor. 2. Remove two (2) retaining screws from TP Sensor and remove from throttle body. 3. Install new TP Sensor to throttle body. Install retaining screws and hand tighten lightly. Adjustment will be required. Re-install electrical connector to TP Sensor.

Related entry:

how to remove alternator on 2004 kia sedona, firing order diagram kia hyundai 3 5l v6, replace a thermostat on a 2003 kia sedona, 02 kia sedona v6 firing order, 2006 Kia Sorento immoblizer switch, 2005 kia sedona cooling system diagram, 2004 kia sorento daytime running lights, 2006 KIA SORENTO FREON CAPACITY, how to change pcv valve on 2005 Kia Sorento, kia sedona 2001 fuse board diagram,

2002 Kia Sedona No start condition with trouble code P0335 present

0

Filed Under (KIA) by admin on 22-05-2010

download
Customer Concern: No start condition with trouble code P0335 present. Customer said it started to sputter and then would not start after they shut it off. Tests/Procedures: 1. Check the hall effect sensor while cranking on the Yellow/Green wire. A 5 volt square wave is normal. This signal should be consistent and clean. Also verify the Black wire has a good ground and the Brown wire has battery voltage at the crankshaft position sensor. 2. There is a plate in the front of the engine that triggers the crankshaft sensor, verify the timing belt or some debris has not bent or damaged the sensor plate. Potential Causes: Crankshaft Position (CKP) Sensor Wiring

Related entry:

honda P0335 P0339,

Audi A4 Sedan 2002-2004, Audi A4 Avant 2002-2004, Audi A4 Cabriolet 2003-2004 – 1.8 Liter 4-Cyl. 5V Turbo Generic Scan Tool

0

Filed Under (Audi) by admin on 15-09-2009

Check the following wire connection for open circuit according to wiring diagram:Relay carrier in E-box, plenum chamber, position 3Terminal Harness connector atignition coils Terminal 8 1 Specified value: Wire resistance max 1.5 – If necessary, repair wire connection. Audi A4 Sedan 2002-2004, Audi A4 Avant 2002-2004, Audi A4 Cabriolet 2003-2004 – 1.8 Liter 4-Cyl. 5V Turbo Generic Scan Tool, Engi…Page 5 24-158 If no malfunctions are found in wires: – Check voltage supply of Motronic Engine Control Module (ECM) voltage supply relay – J271 – Page 24-158 . – Check activation of Motronic Engine Control
Module (ECM) voltage supply relay – J271 – Page 24-159 . Checking voltage supply If specified value is not obtained:
- Connect multimeter for voltage measurement as follows. Relay carrier in E-box, plenum chamber, position 3
Terminal

Related entry:

el tiempo 03 chevy trailblazer, 2004 sunfire emission system, 2004 chevy suburban stability system disabled, 2004 chevy impala 3 4 transmission band adjustment specs, Replacing a Evap Canister on a 2004 Jeep Liberty, 2004 mercedes c240 fuse chart, sunvisor repair audi a4, audi a4 2002 cooling system repair manuel, 2004 jetta 2 0 cooling system schematic, 2002 audi quattro a4 coolant recovery tank install diagram,

2002 Saturn SL2 A/T – 2nd to 3rd Gear Shift Flare

0

Filed Under (Saturn) by admin on 01-10-2010

download
Automatic Transaxle 2-3 Shift Flare During First Minutes of Driving After Cold Soak (Perform Bulletin Procedure) Models: 2002 Saturn S-Series Vehicles with Automatic Transaxle (RPOs MP6, MP7) Attention: General Manager, Fixed Operations Manager, Parts Manager, Technician Condition: Some customers of 2002 S-series vehicles with MP6 or MP7 automatic transaxles may comment on a 2-3 shift flare during the first few minutes of driving after vehicle cold soak. Cause: This condition may be caused by improper pressure, a leak in the 2nd clutch circuit, improper clutch plate finish on 2nd and 3rd clutches, a restriction in the 3rd clutch oil delivery path in the end cover, or improper surface finish in the piston bores of the 2-3 clutch housing. Correction: To correct this condition, duplicate by cold soaking the vehicle the amount of time at temperature described by the owner. Refer to procedure in this bulletin. Service Procedure Verify proper transaxle pressures by installing gauge and performing stepped pressure test after cold soak. Refer to “Stepped Pressure Test” procedure in the 2002 Saturn S-Series Automatic Transaxle Service Manual. ^ If pressures are low, follow the diagnostic chart for DTC P0745 for possible causes of low pressure. Refer to “P0745 – PC Solenoid Pressure Low” diagnostic in the 2002 Saturn S-Series Automatic Transaxle Service Manual. ^ If pressures are within normal ranges, proceed to Step 2. Remove the transaxle end cover. Refer to “End Cover Replacement” in the 2002 Saturn S-Series Automatic Transaxle Service Manual. Check torque on input shaft nut and end cover 3rd clutch oil passage for restrictions. ^ Input shaft nut torque should be 150 N.m (111 ft-lb). If nut is found to be loose, remove nut, clean threads and install new nut using Service Manual procedures and proceed to check 3rd oil passage. ^ Check 3rd oil passage in the end cover by pouring transaxle fluid through it and another passage. If the passage is restricted, you will notice significantly less fluid flow through it. If 3rd clutch passage is found to be restricted, install new end cover per Service Manual procedures and retest for concern. ^ If nut and 3rd clutch passage are okay, proceed to Step 4. Remove transaxle from vehicle. Refer to “Transaxle Removal” in the 2002 Saturn S-Series Automatic Transaxle Service Manual. Disassemble transaxle and install new 2-3 clutch housing, clutch pistons and clutch plates. Refer to “Transaxle Disassemble” in the 2002 Saturn S-Series Automatic Transaxle Service Manual.

Related entry:

sunroof wont open or close 2002 saturn, auto maneul 2002 saurn 200, torque specs axel nut wheelbearing 2002 saturn sl2, torque specs on 2002 saturn sl2 front axel nut, 2002 saturn 200sl gas tank removel, saturn 2002 l300 service manual, saturn front wheel bearing nut touque, saturn 2002 lw300 location of ecm, saturn sl front wheel bearing tourqe specs, saturn sl1 2002 manual download,

2002 Chevy C 1500 Engine Controls – Spark Knock/MIL ON/ DTC P0332 Set

0

Filed Under (Chevrolet) by admin on 03-09-2010

download
Subject: Audible Spark Knock (Detonation), MIL Illuminated, DTC P0332 Set (Replace Rear Bank Knock Sensor and RTV Area Around Sensor) Models: 1998-2002 Chevrolet Camaro, Corvette 1998-2002 Pontiac Firebird with 5.7L Engine (VIN G – RPO LS1) 1999-2002 Chevrolet Silverado, Suburban, Tahoe 2002 Chevrolet Avalance 1999-2002 GMC Sierra, Yukon, Yukon XL 2002 Cadillac Escalade, Escalade EXT with 4.8L, 5.3L or 6.0L Engine (VINs V, T, Z, N, U – RPOS LR4, LM7, L59, L09, L04) This bulletin is being revised to add Cadillac Escalade and Cadillac Escalade EXT to the Models. Please discard Corporate Bulletin Number 02-06-04-023 (Section 6 – Engine/Propulsion System). Condition Some customers may comment on a mild to severe engine ping (commonly referred to as spark knock), usually worse during acceleration and/or an illuminated MIL. Upon investigation, the technician may find DTC P0332 set. Cause This condition may be the result of corrosion of the rear bank knock sensor due to water intrusion into the sensor cavity. This condition is more apparent on vehicles in which customers frequently wash the engine compartment

Related entry:

how to replace knock sensors on a 2002 Chev Avalanche, 2002 silverado door removal, 03 chevrolet avalanche how much freon it holds, how to put 2002 kia sportage 2 0cyl back in time does piston have to be on tdc on compression stroke, impala 2002 chilton repair manual, knock sensor location at jaguar xtype 2002 2 5 motor, locate temperature sending unit fot 2002 tahoe, silverado 2002 charging diagram, where is the tcc solenoid on 2002 chevy impalu, Wire harness for front power seats in a 2002 GMC 1500,