corsa seat belt orange tab


You are searching repair manual in PDF format about corsa seat belt orange tab use another keyword for search another post or files



  corsa seat belt orange tab Direct Download speed 5787 Kb/s

  corsa seat belt orange tab Full Version speed 6767 Kb/s




2004–2010 Toyota 4Runner Front Seat Squeak Noise

0

Filed Under (Toyota) by admin on 20-05-2011

download
Some customers may experience a squeak noise due to contact between the seat track locating pin(s) and the ?oor pan location hole(s). The following procedure describes the repair method to correct this condition. 1. Disconnect the negative (–) battery terminal. 2. Remove the plastic front seat track covers, use a Plastic Pry Tool to disengage the claws and carefully remove the plastic seat track covers. NOTE Refer to the appropriate Toyota Repair Manual for each model for detailed instructions on how to remove the plastic seat track covers. 4. Remove the LH front seat assembly. A. Move the seatback to the full upright position. B. Remove the four (4) seat track securing bolts. C. Disconnect the electrical connectors and remove the complete seat assembly. 5. Remove the seat track locating pins. A. With the seat removed from the vehicle, tilt the seat assembly backward to gain access to the seat track locating pins. B. Use a power cut-off tool to cut off the two (2) locating pins leaving 2 mm (0.1 in.) or less of each pin. NOTE • Do NOT permit the power cut-off tool to contact the seat track. ONLY cut off the shaft of the pin (near the base of the seat track). • The seat track locating pins’ function is to ease installation during manufacturing and does NOT provide any other function. Figure 5.. 6. Clean and paint bare metal surfaces. A. Remove any metal shavings from the seat track/seat assembly. B. Clean the bare metal surface of the remainder of the seat track locating pin with wax, grease, and silicone remover. C. To prevent corrosion, coat any bare metal surfaces still attached to the seat track with a brush-on type paint. 7. Install LH front seat assembly. A. Place the seat on the cabin ?oor. B. Reconnect all electrical connectors under the seat. C. Install all four (4) seat track retaining bolts (?ngertight). D. Tighten the two (2) front seat track attaching bolts. NOTE The bolt torque speci?cation varies by model. Please refer to the Repair Manual for the correct bolt torque for the model you are working on. E. Tighten the two (2) rear seat track attaching bolts. NOTE The bolt torque speci?cation varies by model. Please refer to the Repair Manual for the correct bolt torque for the model you are working on. F. Reinstall all plastic seat track covers. 8. Repeat steps 1 – 6 for the RH seat assembly. 9. Reconnect the negative (–) battery terminal. 10. Test power seat operation and seat heater (if equipped) for proper operation. 11. Initialize front passenger occupant classi?cation system and re-initialize any other power systems. Refer to the applicable model and model year repair manual initialization procedures. 12. Inspect SRS warning light operation. 13. Test drive vehicle and con?rm that the seat squeak has been eliminated.

Related entry:

2003 LINCOLN LS POWER SEAT REPAIR, how to repair driver seat motor on 1999 lincoln continental, 2004 trailblazer I6 backseat fuse diagram, 99 bmw 528i noise under car passenger side, 2004 honda pilot drivers seat maintenance, 2004 trailblazer fuse panel rear, 98 tahoe power seat wire diagram, equinox seat diagram, lincoln power seat track repair, seat belt wire diagram 2011 equinox,

Ford Escort, Fiesta, Sierra, Mondeo, P100, 1.8 Diesel/Turbo diesel Camshaft Belt / Fuel Injection Pump Belt Common Causes of Failure

0

Filed Under (Ford) by admin on 05-06-2011

download
Common causes of camshaft timing belt failure on the above vehicles are due to incorrect operating tension, or ingress of dirt, water, or debris entering the timing belt cover. Predominantly on Fiesta models a high percentage of camshaft timing belt failures occur after the ancillary poly ‘V’ drive belt has failed, where strands of material off the broken belt have entered the timing belt cover. This is especially so where an ancillary belt has been fitted that does not contain “Kevlar” based materials. It is therefore important to always remove the timing belt cover to check for belt debris if the ancillary belt has failed. Any contamination that enters the timing belt cover can become compressed between the surfaces of the camshaft timing belt and drive pulleys. This causes wear to both the belt teeth, backing surface, and damage to the drive pulleys, resulting in premature failure of the camshaft timing belt. Later engines have modifications to improve the sealing of the belt cover around the crankshaft pulley, to reduce the level of outside contamination. Incorrect tensioning of the belt during installation will adversely affect the life of the belt. Before fitting a new belt it is important to check and observe the following points :- 1) Right Hand Inner Wing Splash Shield (Fiesta, Escort, Mondeo) This must be fitted and undamaged. 2) Timing Belt Cover Check that all components of the cover are fitted and undamaged. Ensure the latest type of modified cover is fitted. 3) a) Toothed Drive Pulleys Check that the tooth profiles are not worn or damaged. On vehicles built before January 1994 special attention should be given to the nylon toothed pulley situated below the camshaft pulley in a clockwise position on the belt drive (see diag item 4). This should be changed to a modified steel pulley (Ford No. 7053802) plus bolt (6701537). Ensure that the Camshaft and Injection Pump sprockets are free to rotate on the drive locations when the retaining bolts are slackened off. b) 4) a) b) c) Water Pump, Idler and Tensioner Pulleys Check that the belt running surfaces are not worn or damaged. Check that the flanges are running true and not damaged. Check that the water pump, and pulley bearings are in good condition, to ensure correct belt alignment. 5) Crankshaft Pulley The toothed pulley is in two parts. The rear section (Injection Pump Drive) is located onto the crankshaft by a small drive pin. The front section (Camshaft and “Poly V” belt drive) engages onto the rear pulley via a small vee protrusion on the rear face. Should the central fixing bolt for the crankshaft pulley come loose, or an old bolt re-used (Stretch bolt design), it is possible for fretting to take place damaging the locations. The crankshaft and camshaft pulleys can then move out of timing alignment, resulting in valve and piston contact damage. Replacement Procedure As the vehicle is fitted with two timing belts, one to drive the Camshaft, and one to drive the Injection Pump drives, which are driven off the crankshaft pulley, it is strongly recommended that both belts are replaced at the same time. NOTE: Special tools are required to lock the crankshaft, camshaft, and injection pump in the correct angular location when changing the belts, to ensure correct timing position. IMPORTANT: Ensure the engine is cold (not run for 4 hours) before commencing working as this will affect the setting of the timing belt tension and could lead to premature failure. Continued . . . .

Related entry:

1994 volvo 940 how to replace ac belt, ford diagram belts on 460 cid engine, sable 1995 head lamps short no battery failed, 06 nl 350 belt routing, diagram for 2003 kia sedona van shows how ac conditioner belt on picture, will a old fan belt will cause the pulley to loosen on a corsa ultity 2005, pelacing the alternator belt in a 2001 Kia Sephia, auto repair reference about 1996 geo metro alternater attatching belts, 2006 chevy equiox sprpintine belt directions, 04 ford focus belt diagram,

2008 Dodge Charger Seat Back Cushion / Cover Second Row REMOVAL

0

Filed Under (Dodge) by admin on 02-08-2010

download
1. Remove the seat cushion. See: Seat Cushion\Service and Repair\Seat Cushion / Cover – Removal 2. Remove the nut and disconnect the seat belt anchor. 60/40 Seat Back – Wagon 40% SEAT BACK SIDE 1. Fold the 40% section of the seat (2) down. 2. Remove the nuts (5). 3. Pivot the seat back off the pivot pin (3) located on the 60% seat back. 4. Remove the seat back from vehicle. 60/40 Seat Back – Wagon 60% SEAT BACK SIDE 1. With the 40% seat back removed. 2. Fold the 60% section of the seat down. 3. Remove the four nuts attaching seat back (5). 4. Remove the seat back for vehicle. 60/40 Seat Back – Domestic Sedan 40% SEAT BACK SIDE 1. Fold the 40% section of the seat (3) down. 2. Remove the two nuts (4) attaching seat back. 3. Pivot the seat back off the pivot pin (1) located on the 60% seat back (2). 4. Remove the seat back from vehicle. 60/40 Seat Back – Domestic Sedan 60% SEAT BACK SIDE

Related entry:

how to remove the rear seat on a 2009 subaru outback wagon, 2006 f 350 front seat remov?, removeing seat panels on 2008 f350, remove seats from freestarr, remove back seat from 2005 tundra, removable rear seat rav4, pilot 3rd seat entrance directions, navigator 40/20/40 seat removal, how to take out the second row seat in ford freestar 2004 manual, How to take our the back seat of a 2005 Lincoln Towncar,

2008 Dodge Charger Seat Back Cushion / Cover – Removal

0

Filed Under (Dodge) by admin on 31-07-2010

download
1. Remove the seat cushion. See: Seat Cushion\Service and Repair\Seat Cushion / Cover – Removal 2. Remove the nut and disconnect the seat belt anchor. 60/40 Seat Back – Wagon 40% SEAT BACK SIDE 1. Fold the 40% section of the seat (2) down. 2. Remove the nuts (5). 3. Pivot the seat back off the pivot pin (3) located on the 60% seat back. 4. Remove the seat back from vehicle. 60/40 Seat Back – Wagon 60% SEAT BACK SIDE 1. With the 40% seat back removed. 2. Fold the 60% section of the seat down. 3. Remove the four nuts attaching seat back (5). 4. Remove the seat back for vehicle. 60/40 Seat Back – Domestic Sedan 40% SEAT BACK SIDE 1. Fold the 40% section of the seat (3) down. 2. Remove the two nuts (4) attaching seat back. 3. Pivot the seat back off the pivot pin (1) located on the 60% seat back (2). 4. Remove the seat back from vehicle. 60/40 Seat Back – Domestic Sedan 60% SEAT BACK SIDE

Related entry:

2005 honda pilot back seat removal, how to remove the rear seat cushion out of a 1998 buick rivera, 2004 suburban coverseat remuval, honda passenger seat eliminator, honda seat removal srs work around, how to remove a honda pilot front seat cushion, steps remove suburban rear bench,

1998 Jeep Cherokee Drive Belt: Service and Repair

0

Filed Under (Jeep) by admin on 03-01-2011

download
Correct drive belt tension is required to ensure optimum performance of the belt driven engine accessories. There are different types of adjustment gauges for checking either a serpentine or a V-type belt. Use the correct gauge when checking belt tension. Place gauge in the middle of the section of belt being tested (between two pulleys) to check tension. Do not allow the gauge (or gauge adapter) to contact anything but the belt. BELT SCHEMATICS The belt routing schematics are published from the latest information available at the tingle of publication. If anything differs between these schematics and the Belt Routing Label, use the schematics on Belt Routing Label. This label is located in the engine compartment. BELT REPLACEMENT OR ADJUSTMENT- LEFT HAND DRIVE Belt tension is adjusted at the power steering pump bracket and idler pulley assembly. 1. Disconnect negative battery cable from battery. 2. Loosen idler pulley bolt at the power steering bracket. 3. Loosen adjusting bolt until belt can be removed from pulleys. 4. Remove belt. INSTALLATION 1. Check condition of all pulleys. CAUTION: When installing the serpentine accessory drive belt, the belt MUST be routed correctly. If not, the engine may overheat due to the water pump rotating in the wrong direction. 2. Install new belt. 3. Using serpentine belt tension gauge, tighten adjusting bolt until belt reaches proper tension. Refer to Belt Tension at the rear of this section for proper belt tension. 4. After belt is tensioned correctly, tighten idler pulley bolt to 47 Nm (35 ft. lbs.) 5. After idler pulley has been tightened into position, recheck belt tension. Adjust if necessary. BELT REPLACEMENT OR ADJUSTMENT- RIGHT HAND DRIVE (4.0L) 1. Disconnect negative battery cable from battery. 2. Loosen lower alternator mounting bolt and nut. 3. Loosen upper alternator mounting nut. 4. Loosen adjusting bolt at upper alternator bracket until belt can be removed from pulleys. 5. Remove belt. INSTALLATION 1. Check condition of all pulleys.

Related entry:

jeep grand cherokee 2005 serpentine belt diagram, 2005 Jeep cherokee 3 7 limited automatic 4x4 wiring, honda civic hybrid 2005 drive belt tensioner, how many idler wheels on for fusion 4 cyl, 1996 ford 460 alt belt, 99 vectra 2 2 ltr serpentine belt, belt routing diagram for a 2006 ford escape hybrid, change serpentine belt on enclave 3 6 engine, removing 08 hhr serpentine belt, replace 2005 vw passat tdi belt tensioner,