crankshaft seal leaking on focus
You are searching repair manual in PDF format about crankshaft seal leaking on focus use another keyword for search another post or files
crankshaft seal leaking on focus Direct Download speed 5787 Kb/s
crankshaft seal leaking on focus Full Version speed 6767 Kb/s
Filed Under (Ford) by admin on 06-05-2011
All vehicles 1. Remove the transmission. For additional information, refer to Section 307-01 for automatic transmissions or Section 308-03 for manual transmissions. Vehicles with manual transmission 2. Remove the clutch disc and pressure plate. For additional information, refer to Section 308-01. All vehicles IN-VEHICLE REPAIR (Continued) 3. Remove the 10 bolts and flexplate or flywheel. • Discard the bolts. 4. NOTICE: Use extreme care when removing the flywheel front adapter to prevent damage to the alignment dowel pin. Remove the flywheel front adapter. 5. NOTICE: To prevent engine damage, do not remove the rear primary crankshaft flange bolts under any circumstances. If the flange is removed and reinstalled, it will result in engine vibration and premature transmission component wear. NOTICE: Drill only deep enough to penetrate the seal. Engine damage will occur if the seal is drilled too deep. NOTE: On original service seals, if equipped, the wear ring will be removed separately. Using a center punch, mark a location for 2 holes 180 degrees apart, 9.53 mm (0.375 in) from the outer diameter of the crankshaft flange. Using a drill bit of the appropriate size for the Slide Hammer being used, drill a hole on each side of the crankshaft rear seal as shown. Drill the holes to a depth of 8.76 mm (0.344 in) to capture the metal case of the crankshaft rear seal as well as the wear ring. 6. Using the 2 drilled holes, the Slide Hammer and a commercially available body dent puller attachment, walk the seal out of the rear cover by alternating from side to side to remove the crankshaft rear seal. • Discard the crankshaft rear seal. Vehicles with an original service seal 7. NOTE: Original equipment seals will not have a wear ring. If a service part has previously been installed, it will have a wear ring. If the service part was a redesigned seal, the wear ring will have been removed with the seal in the previous step. If the service part was an original service seal, the wear ring will remain in the engine after the seal has been removed. If the wear ring remained in the engine after removing the seal, use the Crankshaft Rear Wear Ring Remover to remove and discard the crankshaft rear seal wear ring. All vehicles 8. Clean and inspect the crankshaft sealing surface. Installation Vehicles with an original service seal 1. NOTICE: The crankshaft rear seal and wear ring are a one-piece design and need to be installed as an assembly. Do not separate the wear ring from the crankshaft rear seal or damage to the seal may occur. NOTE: An original service seal will have a wear ring without a flange and pre-applied threadlock. NOTE: Apply a bead of threadlock around the circumference of the outer rear edge of the secondary crankshaft flange.
Filed Under (Ford) by admin on 14-03-2011
1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section 100-00. 2. Remove the cooling fan and the cooling fan shroud. For additional information, refer to Section 303-03. 3. Remove the accessory drive belt. For additional information, refer to Section 303-01A. 4. Remove the parts in the order indicated in the following illustration and table. 5. To install, reverse the removal procedure. 6. To install, reverse the removal procedure. Item 1: Crankshaft Pulley Bolt Removal Note 1. Remove the bolts and position the power steering cooler aside. 2. CAUTION: This bolt is torque-to-yield and cannot be reused. Using the special tool to hold the crankshaft pulley, remove and discard the damper bolt. Item 2: Crankshaft Pulley Removal Note 1. Using the special tools and two 8 mm (0.31 in) x 1.25 x 100 mm bolts, remove the crankshaft pulley. Item 3: Front Crankshaft Seal Removal Note 1. Using the special tool, remove the crankshaft front seal. Item 3: Front Crankshaft Seal Installation Note 1. Using the special tool, install the crankshaft front seal. Item 2: Crankshaft Pulley Installation Note
Filed Under (Mercury) by admin on 01-09-2010
Material 1. 2. 3. 4. With the vehicle in NEUTRAL, position it on a hoist. Remove the fan shroud. Remove the accessory drive belt. Remove the parts in the order indicated in the illustration and table.5. To install. reverse the removal procedure. 6. To install, reverse the removal procedure. Item 1: Crankshaft Pulley Bolt Removal Note 1. Remove the bolts and position the power steering cooler aside. 2. CAUTION: This bolt is torque-to-yield and cannot be reused. Using the special tool to hold the crankshaft pulley. remove and discard the damper bolt. Item 2: Crankshaft Pulley Removal Note 1. Using the special tool and two 8 mm (0.31 inch) x 1.25 x 100 mm bolts, remove the crankshaft pulley. Item 3: Front Crankshaft Seal Removal Note 1. Using the special tool, remove the crankshaft front seal. Item 3: Front Crankshaft Seal Installation Note 1. Using the special tool, install the crankshaft front seal.
Filed Under (Ford) by admin on 06-04-2011
Engine Front Cover If the engine front cover (6019) is being removed to check timing chain deflection, refer to Timing Chain Deflection Procedure as outlined in Section 03-00. SPECIAL SERVICE TOOL(S) REQUIRED Description Crankshaft Damper Remover Vibration Damper and Seal Replacer T82L-6316-A Vibration Damper Remover Adapter Removal 1. Remove engine (6007) from vehicle. Refer to procedure in this section. 2. Loosen drive belt tensioner (6B209) and drive belt (8620) . 3. Remove water pump pulley retaining bolts and water pump pulley (8509) . 4. Remove retaining bolts and disconnect heater water outlet tube (18663) from water pump (8501) . 5. Disconnect electrical connector at camshaft position sensor. 6. Disconnect electrical connector at crankshaft position sensor (CKP sensor) (6C315) . 7. Remove retaining bolt and disconnect radiator lower hose tube (8291) from water pump . NOTE: If the vibration damper and crankshaft pulley have to be separated, mark the vibration damper and crankshaft pulley so that they may be reassembled in the same relative position. This is important as the vibration damper and crankshaft pulley are initially balanced as a unit. NOTE: If the vibration damper is being replaced, check if the original vibration damper has balance pins installed. If so, new balance pins (6A328 or equivalent) must be installed on the new vibration damper in the same position as the original vibration damper. The crankshaft pulley (new or original) must also be installed in the same relative position as originally installed. 8. Remove crankshaft pulley (6312) and vibration damper assembly using Crankshaft Damper Remover T58P-6316-D and Vibration Damper Remover Adapter T82L-6316-B. 9. Remove four retaining bolts and remove brace from A/C bracket and P/S bracket. 10. Remove oil bypass filter (6714) . Tool Number T58P-6316-D T82L-6316-B CAUTION: The engine front cover cannot be removed without lowering the oil pan (6675) . 11. Remove oil pan . Refer to procedure in this section. CAUTION: Do not overlook the engine front cover retaining bolt located behind the oil pump and filter body (6603) . The engine front cover will break if pried upon and all retaining bolts are not removed. 12. Remove engine front cover retaining bolts. It is not necessary to remove water pump . 13. Remove engine front cover and water pump as an assembly. 14. Remove engine front cover gasket and discard. Water Pump Tightening Sequence Installation NOTE: Lightly oil all bolt and stud bolt threads before installation except those specifying special sealant. 1. Clean gasket surfaces on the engine front cover and cylinder block (6010) . If reusing the engine front cover , replace crankshaft front seal (6700) . Refer to Crankshaft Pulley and/or Damper and/or Crankshaft Front Seal in this section. 2. If a new engine front cover is to be installed: Install oil pump and filter body . Clean water pump gasket surface. Position a new water pump housing gasket (8507) on the engine front cover and install water pump . Install water pump retaining bolts. Tighten to 20-30 Nm (15-22 lb-ft). 3. Lubricate crankshaft front seal with clean engine oil XO-10W30-QSP or -DSP or equivalent meeting Ford specification ESE-M2C153-E. NOTE: Gasket and Trim Adhesive D7AZ-19B508-B or equivalent meeting Ford specification ESE-M2G52-A is recommended to hold the engine front cover gasket (6020) in position while the engine front cover is installed. 4. Position a new engine front cover gasket on the cylinder block and install the engine front cover / water pump assembly using dowels for proper alignment. 5. Install the engine front cover retaining bolts. Tighten to 20-30 Nm (15-22 lb-ft). Install the capscrew (Part No. N804841) nearest the oil bypass filter flange last, and tighten last. Apply Loctite® or equivalent to bolt prior to installation. Refer to illustration under Step 13 of removal procedure. 6. Install oil pan as outlined. 7. Install oil bypass filter . 8. Coat pulley sealing surface with clean engine oil XO-10W30-QSP or -DSP or equivalent meeting Ford specification ESE-M2C153-E. NOTE: When using silicone rubber sealer, assembly must occur within 15 minutes after sealer application. After this time, the sealer may start to setup, and its sealing effectiveness may be reduced. 9. Apply a small amount of Silicone Gasket and Sealant F1AZ-19562-A or equivalent meeting Ford specification WSE-M4G320-A2 to crankshaft keyway. 10. Position crankshaft key (6B316) in the crankshaft keyway.
Filed Under (Mazda) by admin on 19-11-2010
REMOVAL & INSTALLATION See Figures 1, 2, 3, 4 and 5 1. Disconnect the negative battery cable. 2. Remove the engine fan/clutch assembly and shroud. 3. Remove the accessory drive belt(s). 4. On those engines with a separate damper and pulley, remove the retaining bolts, then separate the crankshaft damper from the pulley. 5. Remove the pulley-to-crankshaft bolt and washer. Fig. Fig. 1: If necessary on some engines, assemble a puller to the damper … Fig. Fig. 2: … then tighten the center bolt to remove the damper from the crankshaft Fig. Fig. 3: Loosen the crankshaft pulley center nut by installing a small bolt on the outside of the pulley, using a prybar for holding force and a socket and breaker bar Fig. Fig. 4: Remove the crankshaft pulley retaining bolt Fig. Fig. 5: Remove the crankshaft pulley, keep the small bolt in for installation purposes 6. If necessary, use a puller tool to remove the damper/pulley from the crankshaft. 7. If equipped, remove the crankshaft key. To install: WARNING On MPV models equipped with the 3.0L engine, the crankshaft position sensor rotor is on the rear of the damper/pulley and can be easily damaged. 8. Inspect the front cover seal and replace if necessary. 9. On 3.0L (B Series Pick-up) and 4.0L engines, perform the following: a. Coat the rubbing surface of the damper/pulley with clean engine oil. b. Apply a small amount of RTV sealant to the damper keyway groove. c. On the B Series Pick-up with the 3.0L engine, use a crankshaft damper installation tool to press the damper onto the crankshaft. Install and tighten the retaining bolt to 93-121 ft. lbs. (125-165 Nm).