diagram of voyager rear drum brakes


You are searching repair manual in PDF format about diagram of voyager rear drum brakes use another keyword for search another post or files



  diagram of voyager rear drum brakes Direct Download speed 5787 Kb/s

  diagram of voyager rear drum brakes Full Version speed 6767 Kb/s




2002 Ford Ranger Brakes – Rear Brakes Grabbing Condition

0

Filed Under (Ford) by admin on 08-11-2010

download
Some vehicles may exhibit a grabbing condition from the rear brakes during the first few brake applications. The condition only occurs after the vehicle has been parked for several hours. ACTION Follow the Service Procedure steps to correct the condition. SERVICE PROCEDURE To service, reduce/minimize moisture intrusion into the rear drum brake assemblies by applying Motorcraft® Silicone Gasket and Sealant to the brake backing plate. 1. Place vehicle on hoist and remove the rear wheels. 2. Remove the rear brake drums and replace the rear linings. Refer to Workshop Manual (WSM), Section 206-02. WARNING Do not breathe dust or use compressed air to blow dust from storage containers or friction components. Remove dust using government-approved techniques. Friction component dust may be a cancer and lung disease hazard. Exposure to potentially hazardous components may occur if dusts are created during repair of friction components, such as brake pads and clutch discs. Exposure may also cause irritation to skin, eyes and respiratory tract, and may cause allergic reactions and/or may lead to other chronic health effects. If irritation persists, seek medical attention or advice. Failure to follow these instructions may result in serious personal injury. 3. Inspect the rear brake assemblies for damaged, missing and/or improperly seated adjuster plug or parking brake cable. 4. Inspect and clean the lining contact area of the brake drum; machine if necessary. 5. Reinstall the rear brake drums and adjust the lining to drum clearance per WSM, Section 206-02. 6. Thoroughly clean the backside of the rear drum brake backing plate to promote proper adhesion of sealant. 7. Apply Motorcraft(R) Silicone Gasket and Sealant to the backside of the rear drum brake backing plate at the following inter[ace areas (Figure 1): ^ Axle Flange ^ Wheel Cylinder ^ Parking Brake Cable ^ Hold Down Pins NOTE AVOID GETTING SEALANT ON THE BRAKE BLEED SCREW AND BRAKE TUBE NUT. 8. Reinstall the rear wheels and torque lug nuts per Workshop Manual, Section 204-04.

Related entry:

2006 ford escape rear caliper brake adjustmen which way to adjusters tur?, replacing rear drum drakes 2000 chrysler town an country, left brake drum in 2005 chevy equinox diagram, bleeding brakes kia sportage, youtube 2005 chevy 2005 chevy colorado rear brakes replacement, g20 van rear brake inspection and replacement, torque toyota brake caliper sequoia, exploded view rear brakes 1995 tahoe 2 door, 1995 g20 van rear jacking instructions, howtoreplacerearbrakeson2001toyotarav4,

1995 Ford Thunderbird Spring REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 02-03-2011

download
Removal 1. Raise vehicle on hoist. Refer to Section 00-02. 2. Remove rear wheel and tire assembly. 3. Remove rear stabilizer bar link and bushing link nuts at both ends of rear stabilizer bar (5A772) . Rotate bar up and out of the way. 4. Disconnect parking brake rear cable and conduit (2A635) at rear disc brake caliper (2553) . 5. Install three Rotunda Spring Cages 086-00031 or equivalent to rear spring as follows: a. Install one spring cage without an adjuster link to the inboard side (the innermost “bend” of the rear spring (5560) ). b. Install two more spring cages, with adjusters, at 120 degree angles to the previously installed cage. Spring, Rear 6. Place a transmission jack or suitable stand under the rear suspension arm and bushing (5500) as far outboard as possible. 7. Support the rear wheel knuckle (5A969) assembly by wiring the rear suspension arm and bushing to the body. 8. Remove lower rear shock absorber mounting bolt, washer and nut. 9. NOTE: Rear suspension arm and bushing must not be lowered until pivot bolts are loose. Do not attempt to remove plastic cap on front pivot nut. Loosen both inboard pivot bolts on rear suspension arm and bushing . 10. Remove two bolts and nuts retaining rear suspension arm and bushing to rear wheel knuckle . 11. Lower the rear suspension arm and bushing by lowering jack. Ensure spring cages properly seat on rear spring as rear suspension arm and bushing is dropped. 12. Remove jack, lower rear suspension arm and bushing down fully by hand and remove rear spring with cages in place. 13. Remove rear spring center mounting insulators (5741) , if necessary. 14. If spring cages are to be removed for installation on rear spring , use Coil Spring Compressor D78P-5310-A or equivalent to compress rear spring and remove cages. Rear spring center mounting insulator should be installed on rear spring before installing rear spring in tool to prevent slipping of plates.

Related entry:

2004 Ford Explorer Differential Diagram, step by step instruction on how to change struts on 1995 740i BMW?, BMW X5 Rear Suspension Diagram, blow up diagrams of 2002 ford E150 rear axle, 2008 jeep patriot rear drum breaks disassembly, diagram of dodge hatch lock, 2002 Tahoe rear AC Diagram, 2005 dodge stratus sxt front suspension parts diagram, install knuckle bushing buick, installing rear stut mounting bracket on 2004 chrysler sebring,

2006 Honda Civic Rear ABS Wheel Speed Sensor and O-Ring Inspection

0

Filed Under (Honda) by admin on 10-01-2011

download
During assembly, some wheel speed sensors may have been improperly installed and do not seal the hub assembly. Water may enter the hub assembly and damage the wheel bearing. In areas where road salt is used, the wheel bearings may corrode, which may cause the wheel to separate and fall off, increasing the risk of a crash. CORRECTIVE ACTION Inspect both rear ABS wheel speed sensors and their O-rings. If an ABS wheel speed sensor or O-ring is damaged, replace the damaged part and the hub bearing unit on that wheel. REPAIR PROCEDURE 1. 2. 3. 4. Raise the vehicle on a lift. Remove the rear wheels. Remove both rear ABS wheel speed sensors. Inspect the rear ABS wheel speed sensors and their O-rings. • If a rear ABS wheel speed sensor O-ring is damaged (cut, torn, pinched, or flattened), replace the O-ring and the corresponding rear hub bearing unit, then go to step 5. DAMAGED O-RINGS: O-ring is pinched. • If the rear ABS wheel speed sensor tip has any physical damage, remove the original sensor assembly, replace the corresponding rear hub bearing unit(s), and connect the new sensor’s wire harness. Then go to step 5. – Refer to page 18-34 (with disc brakes) or 18-36 (with drum brakes) of the 2006–07 Civic Service Manual, or – Online, enter keyword HUB, then select Rear Knuckle/Hub Bearing Unit Replacement from the list. O-ring is rolled out of the groove and flattened. -Refer to page 18-34 (with disc brakes) or 18-36 (with drum brakes) of the 2006–07 Civic Service Manual, or – Online, enter keyword HUB, then select Rear Knuckle/Hub Bearing Unit Replacement from the list. • If the rear ABS wheel speed sensors and their O-rings are OK, go to step 5. 5. Lubricate the ABS wheel speed sensor O-ring and the sensor hole in the knuckle with multi-purpose grease.

Related entry:

whrrl speed sensors 2006 colorado, vw golf mk3 rear pivot arm bush repairs, on a 94 ranger ABS Brakes dump soleniod acticity, rear driver hub jeep compass assembly diagram, Rear Hub Assembly Diagram, rover 45 anti-lock braking system reluctor ring, rear abs solenoid circuit malfunction after replacing front wheel hub assembly, Reluctor Ring Replacement, removing the reluctor ring off a ford ranger rear axel, replace 2011 jeep patriot rear hub,

2000 Ford F-150 Parking Brake Rear Drum Brakes

0

Filed Under (Ford) by admin on 02-02-2011

download
Remote release handle Parking brake control Parking brake rear cable and conduit clip (part of 2A635) Parking brake cable bracket Parking brake rear cable and conduit— (LH) Parking brake rear cable and conduit— (RH) Parking brake cable equalizer Front parking brake cable and conduit Front parking brake cable clip The parking brake system is actuated when the parking brake control (2780) is depressed. The parking brake control applies tension to the front parking brake cable and conduit (2853) and parking brake cable equalizer (2A602). The parking brake cable equalizer is coupled to the RH parking brake rear cable and conduit (2A635) and the LH parking brake rear cable and conduit. The respective rear brake assemblies are then applied. The rear wheel brake assembly contains a cable-actuated parking brake assembly. The parking brake releases the rear brakes using a remote release lever incorporated with the parking brake control. If the parking brake control is not fully released, the parking brake signal switch will illuminate the brake warning light. The parking brake signal switch is mounted on the parking brake control. The switch is held in place by a self-tapping screw and aligned with a locater pin. The drum brake parking brake system is self-adjusting, therefore cable tension does not need to be adjusted. Rear Disc Brakes Parking Brake Components, Rear Disc Brakes

Related entry:

how to change back break shoes on a mercury mystique, 2011 international prostar brake light switch location, service manuel for P30 auto parking brake, 09 corolla rear brake diagram, 1996 chevrolet pickup brake light switch replacement instructions, skimatics on saturn 2000 rear brakes, schematic of parking brakes on a 2001 silverado, oo3 ranger parking release exploded view, P30 Brakes Manual, parking brake drag 2006 Jaguar xjr,

2004 Ford F-150 Rear Axle Differential Cover Axle Shaft Oil Seal and Rear Wheel Bearing REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 28-02-2011

download
1. With the vehicle in NEUTRAL, position on a hoist. For additional information, refer to Section 100-00. 2. Remove the rear wheel and tire assembly. For additional information, refer to Section 204-00. 3. Remove the parts in the order indicated in the following illustration and table. 4. To install, reverse the removal procedure. 5. Fill the axle with the specified quantity of the specified lubricant. For additional information, refer to the Specifications in this section. Item 2: Rear Disc Brake Caliper Removal Note 1. CAUTION: Do not allow the caliper to hang from the brake hose. Provide a suitable support. Position the rear disc brake caliper aside. For additional information, refer to Section 206-00. Item 7: Differential Pinion Shaft Removal Note 1. Move the differential pinion shaft out far enough to remove the U-washers. Replace the shaft and install the lock bolt finger tight when U-washers are removed. Item 8: U-washer Removal Note 1. CAUTION: Do not damage the rubber O-rings in the axle shaft grooves. Remove the U-washers. 1. Push the axle shafts inboard. 2. Remove the U-washers. Item 10 and 11: Wheel Bearing Oil Seal and Axle Shaft Bearing Removal Note 1. CAUTION: Never remove the wheel bearing oil seal by itself. Always remove the wheel bearing oil seal and the rear wheel bearing at the same time. For the 8.8 inch rear axle, use the special tools to remove the rear wheel bearing and wheel bearing oil seal. 2. CAUTION: Never remove the wheel bearing oil seal by itself. Always remove the wheel bearing oil seal and the rear wheel bearing at the same time. For the 9.75 inch and the 10.25 inch rear axles, use the special tools to remove the rear wheel bearing and wheel bearing oil seal. Item 11: Axle Shaft Bearing Installation Note 1. For the 8.8 inch and the 9.75 inch rear axles, use the special tools to install the rear axle wheel bearing. 2. For the 10.25 inch rear axle, use the special tools shown to install the rear axle wheel bearing. Item 10: Wheel Bearing Oil Seal Installation Note 1. Use the special tools shown to install the rear wheel bearing oil seal. Item 8: U-washer Installation Note 1. CAUTION: Do not damage the rubber O-rings in the U-washer grooves. Install the U-washers. 1. Position the two U-washers on the button end of the axle shafts. 2. Pull the axle shafts outward.

Related entry:

2004 ford explorer rear differential diagram, tourch on rear wheel bearing on a 2010 chevy impala, 2006 suzuki forenza front wheel drive axle diagram, 2008 chevy silverado cv axle nut size, 2004 expedition right axle tube seals, balance shaft seal for 2004 honda acccord 4 cylinder schematic, saturn wheel hub torque specs, how to remove rear axle shaft of mitsubishi strada triton, 2004 ford escape rear gears, 2002 chevy silverado 1500 front end exploded view,