diagram to remove automatic transmission selector lever cable s10 blazer


You are searching repair manual in PDF format about diagram to remove automatic transmission selector lever cable s10 blazer use another keyword for search another post or files



  diagram to remove automatic transmission selector lever cable s10 blazer Direct Download speed 5787 Kb/s

  diagram to remove automatic transmission selector lever cable s10 blazer Full Version speed 6767 Kb/s




2006 Ford Explorer 6R60 Transmission Selector Lever Cable REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 07-05-2011

download
Selector Lever Cable Vehicles Equipped with a 6R60 Transmission Removal All vehicles 1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section 100-02. 3. With the selector lever in PARK, disconnect the selector lever cable from the selector lever. Vehicle equipped with a 6R60 transmission 6. Remove the cable shield by prying on the shield closest to the boot, then sliding the shield away from the boot. 4. Disconnect the selector lever cable from the selector lever housing. 7. Unlock the lock tab and disconnect the selector lever cable end from the transmission manual lever. 5. Pull the cable and grommet through the floorpan. 8. Disconnect the selector lever cable from the bracket and remove the cable. Vehicles equipped with a 5R55S transmission 9. Remove the cable shield by prying on the side of the shield closest to the boot, then sliding the shield away from the boot. 10. Unlock the lock tab and disconnect the selector lever cable end from the transmission manual lever. 11. Disconnect the selector lever cable from the bracket and remove the cable. Installation Vehicles equipped with a 6R60 transmission 1. Install the selector lever cable into the bracket. 2. Connect the selector lever cable end onto the transmission manual lever and lock the lock tab. 3. NOTE: If the shield is loose, install a new shield. Install the cable shield. Vehicles equipped with a 5R55S transmission 4. Install the selector lever cable into the bracket. 5. Connect the selector lever cable end onto the transmission manual lever.

Related entry:

how to remove shifting cable from shifter on 2002 saab 9-3 conv, maruti 800 gear lever arm, youtube how to change gear selector cable in 2003 tracker 4 wheel drive, 2007 kia spectra shift lever, B-Mode selector on the Mirage?, how to install gear selecter cable on 2003 tracker 4 wheel drive, how to replace 2003 tracker gear selecter cable 4 wheel drive,

2003-2005 Chevrolet TrailBlazer Automatic Transmission/Torque Converter Clutch (TCC) Shudder

0

Filed Under (Chevrolet) by admin on 30-12-2010

download
Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Condition Some customers may comment on a shudder condition at approximately 64-80 km/h (40-50 mph) when the TCC engages. Cause This condition may be caused by water in the automatic transmission fluid (ATF). Water may enter the transmission by dripping from the cowl area onto the handle of the transmission fluid level indicator. Indications of water in the ATF may include: • Visible rust on the transmission fluid level indicator. • Visible water in the oil pan. • A milky white substance inside the pan area. • Spacer plate gaskets that appear to be glued to the spacer plate, valve body or case. • Rust on internal transmission iron/steel components. Correction First, repair the transmission and second, replace the transmission fill tube, seal and level indicator to prevent repeat water contamination of the ATF. Transmission Repair 1. Remove the transmission. Refer to the appropriate SI procedure. 2. Disassemble and inspect the transmission. Refer to Unit Repair Automatic Transmission – 4L60-E/4L65-E. Important: If water or coolant is found in the transmission, the following components MUST be replaced. • Replace all of the rubber type seals. • Replace all of the composition-faced clutch plate assemblies including the band. • Replace all of the nylon parts (Thrust Washers). • Replace the torque converter. • Thoroughly clean and rebuild the transmission, using new gaskets and oil filter. • Flush and flow check the transmission oil cooler using J 45096. Refer to Corporate Bulletin Number 02-07-30- 052C or newer – Automatic Transmission Oil Cooler Flush and Flow Test Essential Tool J 45096 TransFlow . Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator WITH the transmission REMOVED from vehicle. 1. Remove the transmission fluid filler tube from the transmission. 2. Replace the transmission fill tube seal, P/N 1259475. 3. Replace the transmission fill tube, P/N 15000220, following the appropriate SI Document for Transmission Installation. 4. Replace the transmission fluid level indicator, P/N 15069769 when appropriate during the transmission installation. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator with the transmission in the vehicle. 1. Remove the air cleaner outlet duct. Refer to Air Cleaner Element Replacement (SI Document ID# 1364496). 2. Remove the transmission fluid level indicator from the filler tube.

Related entry:

parking paw actuator rod assembly 5r55e, 1985 chevy silverado transaxle support brace, 2003 trailblazer torque converter removal, high pressure transmission filter for cvt trans 07 ford freestyle, how to change transmition lines on 2007 trailblazer, how are the coolant line ran on a 2003 santa fe, manual transmission diagram 1995 sl1, mazda 626 transmission cooler install, explorer 2003 automatic transmission delayed engagement, refill plug location for transmision on 2011 camry 4 cyl automatic,

1999 Ford F-Super Duty 250-550 Automatic Transaxle/ Transmission Cable and Bracket Removal and Installation

0

Filed Under (Ford) by admin on 14-03-2011

download
1. NOTE: To prevent cable damage, do not apply force to the transmission shift cable assembly between the steering column shift tube bracket and the steering column bracket. Disconnect the transmission shift cable from the steering column. 1. Disconnect the transmission shift cable from the steering column shift tube lever. 2. Carefully lift the locking tab and disconnect the transmission shift cable from the steering column bracket. 2. Disconnect the cable push pin from the stud in the bulkhead. 3. Push the rubber grommet and transmission shift cable through the bulkhead. 4. Raise and support the vehicle. For additional information, refer to Section 100-02. 4R100 transmission 5. NOTE: To prevent shift cable assembly damage, do not apply force to the transmission shift cable between the manual control lever and the transmission shift cable bracket. Remove the transmission shift cable from the transmission. 1. Disconnect the transmission shift cable from the manual control lever. 2. Depress the lock tabs to release the transmission shift cable and disconnect the transmission shift cable from the transmission shift cable bracket. 6. Remove the shift cable bracket from the transmission. 1. Remove the bolts. 2. Remove the shift cable bracket. 7. To install, reverse the removal procedure. Adjust the shift cable. For additional information, refer to Cable and Bracket Adjustment—4.2L, 4.6L with 4R70W Transmission or Cable and Bracket Adjustment—5.4L, 6.8L, 7.3L Diesel With 4R100 Transmission in this section.

Related entry:

floor shifter 1998 monte carlo manual, algo-twcrecommends_if2, corvette c5 automatic shift cable, 1999 infiniti g20 overdrive operation, 2004 Trailblazer Shift Linkage Bushing, 03 mazda protege gear shift cable repair, gear selecter 2004 gmc envoy xuv, diagram to remove a 2001gear shift panel fro 2001 toyota corolla, pictures of 2001 ford escplorer shifter cable, how to repair hood cable on 2004 jaguar x type,

1993 Mitsubishi Montero TRANSFER CASE DISASSEMBLY

0

Filed Under (Mitsubishi) by admin on 30-12-2010

download
Disassembly (Ram-50) 1) Remove both 4WD indicator switches and steel balls. Remove speedometer gear assembly. Remove output shaft cover, gasket, wave spring and spacer. See Fig. 3. Remove rear cover, rear cover gasket and spacer from chain cover. Drive roll pin out of high-low shift fork. 2) Remove 2 seal plugs. Remove 2 poppet springs and steel balls. Shift transfer case to “4WD” and pull high-low shift rail out, in rear cover direction. Remove interlock plunger. Remove pulse generator (if equipped), front output shaft cover and pulse rotor (if equipped). Remove snap ring from rear bearing on output shaft. Remove chain cover, oil guide and side cover. Remove countershaft locking plate. Remove countershaft. 3) Remove countergear, 2 thrust washers, 2 needle bearings and spacer through side cover opening. Remove snap ring, spring retainers and spring from 2WD-4WD shift rail. Remove front output shaft, rear output shaft and chain as assembly. 4) Remove 2WD-4WD shift fork and distance piece. Drive out 2WD-4WD shift rail spring pin. Remove 2WD-4WD shift rail and lug. Remove high-low shift fork and high-low synchronizer sleeve. Remove needle bearing and snap ring from input gear. Remove input gear assembly. 5) If either control shaft or input gear oil seals are to be replaced, drive out roll pin from transmission control change shifter. Separate transfer case from adapter. See Fig. 3. Disassembly (Montero) 1) Remove dynamic damper, 5 detection switches and 3 steel balls. Remove poppet plug, spring and steel ball. Remove speedometer gear assembly. Remove output shaft rear cover, spacers, dust seal guard and oil seals. Front output shaft cover, wave spring and spacer (if equipped). 2) Remove high-low shift rail plug and high-low shift fork spring pin. Shift transfer case to “4WD”. Remove rear cover and high- low shift rail. Remove interlock plunger. Remove rear output shaft (viscous coupling) assembly and center differential assembly. Remove 2WD-4WD synchronizer assembly, chain and front output shaft from transmission as a unit. With White paint make match marks in grooves of 2WD-4WD synchronizer in 3 places. With White paint make match marks on spline projections of 2WD-4WD synchronizer sleeve in 3 places. Refer to match marks during reassembly. 3) Remove snap ring, spring seat, spring, 2WD-4WD shift fork and 2WD-4WD synchronizer sleeve. Remove differential lock hub, oil dam cover and bearing retainer. Remove side cover and gasket. Remove transfer counter gear shaft, transfer counter gear, thrust washer, needle bearings and spacer. Remove transfer drive shaft assembly. Remove high-low shift fork assembly and clutch sleeve. Remove transfer input gear assembly. 4) Remove 2WD-4WD shift lug spring pin, spring, spring retainer 2WD-4WD shift lug and shift rail. Remove input gear oil seal, baffle plate, dust seal guard and front output shaft oil seal. See Fig. 4.

Related entry:

how to remove a rack and pinion 2004 gmc envoy, removing the dash pad in a 2000 porsche boxster, 2006 Dodge Caravan tailgate removal, how to remove a visor from a subaru outback, f250 ashtray removal, vw t4 gear lever removal, 1996 VW Golf Manual Shift Linkage, How to replace an antenna on a S10 blazer, disconnect anti theft fuse on 1991 sadandiville diagram, Remove Snap ring on 2004 toureg drive shaft,

1994 Ford Mustang A/C Evaporator Housing Removal and Installation

0

Filed Under (Ford) by admin on 06-03-2011

download
1. Disconnect battery ground cable (14301) . 2. Remove two console armrest mounting access covers (047A62) at rear of console panel (045A36) (snaps out) to gain access to armrest retaining bolts. 3. Remove four armrest-to-floor bracket retaining bolts and remove armrest assembly (snaps out of console). 4. Remove console panel gear shift plate (044G24) (snaps out). On vehicles equipped with manual transmissions, shift boot is attached to bottom of finish panel. Remove shift knob and slide boot and console panel gear shift plate up shift lever to remove. 5. To remove top finish panel position emergency brake lever in the UP position. Remove four retaining screws and lift top finish panel up. Disconnect necessary wire connectors. 6. Remove two console-to-rear floor bracket retaining screws. 7. Insert a small screwdriver into two notches at bottom of front upper finish panel and snap out. 8. If the vehicle has a radio chassis (18806) , the radio chassis must be removed. Refer to Section 15-01. If the vehicle doesn’t have a radio chassis , use a small screwdriver and pry radio cover finish panel out of console. 9. Flex glove compartment bin tabs inward. Drop down glove compartment (06010) assembly. Remove two console-to-instrument panel retaining screws. 10. Remove four console bracket retaining screws. Remove console panel from vehicle. 11. Remove three bolts retaining steering column opening cover (3A673) and reinforcement panel. Remove cover. 12. Remove steering column opening reinforcement by removing two bolts. 13. Remove two bolts retaining steering column opening reinforcement and remove reinforcement. 14. Remove six steering column retaining nuts (two retaining the hood release mechanism and four retaining column to lower brake pedal support). Lower steering column to floor. 15. Remove upper and lower steering column shrouds (3530) and disconnect wiring from turn signal and windshield wiper switch (13K359) . 16. Remove steering column through bolt and nut on engine compartment side of cowl panel. Remove steering column from vehicle. 17. Remove brake pedal support nut. 18. Snap out instrument panel defroster opening grille (044E82) . 19. Remove screws from speaker covers. Snap out speaker covers. 20. Remove front screws retaining RH and LH scuff plates at cowl side trim panels. 21. Remove RH and LH cowl side trim panels. 22. Disconnect wiring at RH cowl side. 23. Remove cowl side retaining bolts (one each side). 24. Remove five cowl top screws attachments. 25. Gently pull instrument panel (04320) away from RH side of cowl panel. Disconnect speedometer cable, air conditioning controls and wire connectors. 26. Place a drain pan or suitable container under the heater water hose connections at the cowl panel. 27. Disconnect heater water hoses (18472) from heater core tubes and plug heater water hoses with suitable 5/8-inch and 3/4-inch plugs. Cap heater core tubes to prevent coolant loss from heater core (18476) during removal of heater case. 28. Remove screw retaining A/C evaporator case support bracket (19A639) to cowl top panel. 29. Disconnect vacuum supply supply hose (black) from A/C vacuum supply in engine compartment. 30. Working under the hood (16612) , remove nut retaining heater case to cowl panel. 31. Inside passenger compartment, remove screw retaining A/C evaporator case mounting bracket (19A865) to cowl top panel. 32. Remove one screw retaining A/C evaporator case mounting bracket below heater case to cowl panel. 33. Carefully pull heater case from cowl panel and remove heater case assembly from vehicle. 34. To install, reverse Removal procedure. Check operation of all components. 35. After repairs have been completed, check the coolant level in the radiator (8005) and in the radiator coolant recovery reservoir (8A080) . Fill as required with the recommended coolant mixture.

Related entry:

How to remove center console cup holder in a 06 f150 super cab, 94 FORD BRONCO FRONT BUMPER REMOVAL, remove center console e39, remove the rocker panel cover on 2006 altima, remove radio on 2007 milan, lincoln 2003 overhead console, how to remove 1999 cavalier center console, e53 x5 center consdole trim removal, how to take off center console \04 lincoln aviat, equinox console removal,