diagrama de cadena de tiempo del kia rio 2002 1.5


You are searching repair manual in PDF format about diagrama de cadena de tiempo del kia rio 2002 1.5 use another keyword for search another post or files



  diagrama de cadena de tiempo del kia rio 2002 1.5 Direct Download speed 5787 Kb/s

  diagrama de cadena de tiempo del kia rio 2002 1.5 Full Version speed 6767 Kb/s




2006-2009 Hyundai Accent 2006-2009 Kia Rio Dash Disassembly

0

Filed Under (Hyundai) by admin on 16-08-2010

download
1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove the trim panel surrounding the radio and includ- ing the a/c vents. (Figure A) 3 Remove (4) Phillips screws securing the radio. (Figure B) 4 Disconnect and remove radio. (Figure B) Continue to KIT ASSEMBLY. 1 KIA RIO: Cut and remove shaded areas #1. (Figure A) HYUNDAI ACCENT: Cut and remove shaded areas #2. (Figure A) 2 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure B) 3 Slide the aftermarket head unit into the cage until secure. (Figure C) Continue to final assembly.

Related entry:

googlekia rio alarm reset, 2004 kia rio coil pack change, p0742 kia rio 2007, kia amanti 2006 tune-ups, how often a tune up for a 2006 kia amanti, how to adjust handbrake on Hyundai getz, How to remove headliner in a 2003 Kia Sorento, Kia Amanti 2006 immobilizer replacement, kia rio 2002 where is diagnostic plug, location of purge valve 2009 kia rio,

2003 Kia Rio Cinco Service and Repair TIMING BELT

0

Filed Under (KIA) by admin on 05-08-2010

download
REMOVAL 1. Disconnect negative battery cable. 2. Loosen power steering lock bolts and nuts accordingly and remove tension from Power Steering (P/S) and/or Air Conditioning (A/C) compressor drive belt. 3. Remove P/S and/or A/C drive belt. 4. Loosen generator mounting bolts and adjusting bolt. 5. Remove generator bolts. 6. Remove water pump pulley. 7. Remove crankshaft pulley and timing belt guide plate. 8. Remove upper and lower timing belt covers. 9. Turn crankshaft so that timing mark on timing belt pulley is aligned with timing mark on engine. 10. Check that “I” mark on intake camshaft pulley is aligned with mark on cylinder head cover and “E” mark on exhaust camshaft pulley is aligned with mark on cylinder head cover. NOTE: Do not move camshaft or crankshaft once timing marks have been correctly positioned. 11. Loosen tensioner pulley lock bolt. 12. Protect timing belt with a rag. 13. Remove tensioner pulley. 14. Remove timing belt. NOTE: Mark the direction of timing belt rotation (on the timing belt) for proper reinstallation. INSPECTION NOTE: Never forcefully twist, turn inside out or bend timing belt. Do not allow oil or grease to come in contact with timing belt. 1. Replace timing belt if it is contaminated with oil or grease.

Related entry:

autoreparmaunalfor2002KIARiocinco,

Kia Sorento/ Kia Sedona Throttle Position Sensor W/3.5L Engine

0

Filed Under (KIA) by admin on 04-06-2010

download
Description This bulletin provides information related to the Throttle Position Sensor (TPS) for Sorento & Sedona models. Some Sorento & Sedona vehicles may exhibit diagnostic trouble codes P0121 and/or P1121. This condition mainly occurs in high ambient or desert areas, and can be related to the occasional increase in contact resistance due to excessive wear of the inner elements of the TP sensor. This bulletin describes the proper service and adjustment procedure for replacing the TP Sensor. – Service Procedure Replacement Procedure: 1. Turn ignition OFF. Remove engine cover and disconnect electrical connector from TP Sensor. 2. Remove two (2) retaining screws from TP Sensor and remove from throttle body. 3. Install new TP Sensor to throttle body. Install retaining screws and hand tighten lightly. Adjustment will be required. Re-install electrical connector to TP Sensor.

Related entry:

wiring diagram for 2005 kia sedona engine cooling fan temperature sensor, diagram of ac system on 2006 kia sorento, 2008 Kia Sedona Wiring Diagram, 2006 kia sorento ex air compressor coil, operating manual for 2005 kia sedona ac system, p2422 code kia sedona, 2006 kia sedona a/c diagram, how much freon is in a 2004 kis sedona, replacing 2002 kia spectra a/c compressor coil, 2005 kia sedona low speed engine cooling fan wiring diagram,

2002 Saturn SL2 A/T – 2nd to 3rd Gear Shift Flare

0

Filed Under (Saturn) by admin on 01-10-2010

download
Automatic Transaxle 2-3 Shift Flare During First Minutes of Driving After Cold Soak (Perform Bulletin Procedure) Models: 2002 Saturn S-Series Vehicles with Automatic Transaxle (RPOs MP6, MP7) Attention: General Manager, Fixed Operations Manager, Parts Manager, Technician Condition: Some customers of 2002 S-series vehicles with MP6 or MP7 automatic transaxles may comment on a 2-3 shift flare during the first few minutes of driving after vehicle cold soak. Cause: This condition may be caused by improper pressure, a leak in the 2nd clutch circuit, improper clutch plate finish on 2nd and 3rd clutches, a restriction in the 3rd clutch oil delivery path in the end cover, or improper surface finish in the piston bores of the 2-3 clutch housing. Correction: To correct this condition, duplicate by cold soaking the vehicle the amount of time at temperature described by the owner. Refer to procedure in this bulletin. Service Procedure Verify proper transaxle pressures by installing gauge and performing stepped pressure test after cold soak. Refer to “Stepped Pressure Test” procedure in the 2002 Saturn S-Series Automatic Transaxle Service Manual. ^ If pressures are low, follow the diagnostic chart for DTC P0745 for possible causes of low pressure. Refer to “P0745 – PC Solenoid Pressure Low” diagnostic in the 2002 Saturn S-Series Automatic Transaxle Service Manual. ^ If pressures are within normal ranges, proceed to Step 2. Remove the transaxle end cover. Refer to “End Cover Replacement” in the 2002 Saturn S-Series Automatic Transaxle Service Manual. Check torque on input shaft nut and end cover 3rd clutch oil passage for restrictions. ^ Input shaft nut torque should be 150 N.m (111 ft-lb). If nut is found to be loose, remove nut, clean threads and install new nut using Service Manual procedures and proceed to check 3rd oil passage. ^ Check 3rd oil passage in the end cover by pouring transaxle fluid through it and another passage. If the passage is restricted, you will notice significantly less fluid flow through it. If 3rd clutch passage is found to be restricted, install new end cover per Service Manual procedures and retest for concern. ^ If nut and 3rd clutch passage are okay, proceed to Step 4. Remove transaxle from vehicle. Refer to “Transaxle Removal” in the 2002 Saturn S-Series Automatic Transaxle Service Manual. Disassemble transaxle and install new 2-3 clutch housing, clutch pistons and clutch plates. Refer to “Transaxle Disassemble” in the 2002 Saturn S-Series Automatic Transaxle Service Manual.

Related entry:

2002 Saturn L200 Manual, owners manual for 2001 saturn sl1, How much freon does a 2003 avalanche hold?, 2002 Saturn L300 Owners Manual, owners manual for 2002 saturn L200, 2002 saturn driveaxel nut torque, diagrama de saturn 2000 sl1, 1998 Saturn repair manual SW2 Wagon, jetta tcm ending with L, how to remove gas tank on 20002 satura l 300,

Audi A4 Sedan 2002-2004, Audi A4 Avant 2002-2004, Audi A4 Cabriolet 2003-2004 – 1.8 Liter 4-Cyl. 5V Turbo Generic Scan Tool

0

Filed Under (Audi) by admin on 15-09-2009

Check the following wire connection for open circuit according to wiring diagram:Relay carrier in E-box, plenum chamber, position 3Terminal Harness connector atignition coils Terminal 8 1 Specified value: Wire resistance max 1.5 – If necessary, repair wire connection. Audi A4 Sedan 2002-2004, Audi A4 Avant 2002-2004, Audi A4 Cabriolet 2003-2004 – 1.8 Liter 4-Cyl. 5V Turbo Generic Scan Tool, Engi…Page 5 24-158 If no malfunctions are found in wires: – Check voltage supply of Motronic Engine Control Module (ECM) voltage supply relay – J271 – Page 24-158 . – Check activation of Motronic Engine Control
Module (ECM) voltage supply relay – J271 – Page 24-159 . Checking voltage supply If specified value is not obtained:
- Connect multimeter for voltage measurement as follows. Relay carrier in E-box, plenum chamber, position 3
Terminal

Related entry:

yhs-default, how to reset air conditioner 03 silverado, pathfinder vq35 v6 does not start 2004, flasher box barina 2004, Surbane 2004 LT AC manel, 2004 Audi a4 2 0 turbo transmission range sensor location, audi epc warning q7 audi, 2002 audi a4 ac discharge location, audi 500 sel workshop manual, repair manual 2002 eurovan weekender,