disable the SIR system 2002 chevy silverado


You are searching repair manual in PDF format about disable the SIR system 2002 chevy silverado use another keyword for search another post or files



  disable the SIR system 2002 chevy silverado Direct Download speed 5787 Kb/s

  disable the SIR system 2002 chevy silverado Full Version speed 6767 Kb/s




2007 Chevrolet Chevy Suburban SIR Disabling and Enabling

0

Filed Under (Chevrolet) by admin on 16-04-2011

download
SIR component location affects how a vehicle should be serviced. There are parts of the SIR system installed in various locations around a vehicle. To find the location of the SIR components refer to SIR Identification Views . There are several reasons for disabling the SIR system, such as repairs to the SIR system or servicing a component near or attached to an SIR component. There are several ways to disable the SIR system depending on what type of service is being performed. The following information covers the proper procedures for disabling/enabling the SIR system. SIR Service Precautions Caution: When performing service on or near the SIR components or the SIR wiring, the SIR system must be disabled. Failure to observe the correct procedure could cause deployment of the SIR components. Serious injury can occur. Failure to observe the correct procedure could also result in unnecessary SIR system repairs. The inflatable restraint sensing and diagnostic module (SDM) maintains a reserved energy supply. The reserved energy supply provides deployment power for the air bags if the SDM loses battery power during a collision. Deployment power is available for as much as 1 minute after disconnecting the vehicle power. Waiting 1 minute before working on the system after disabling the SIR system prevents deployment of the air bags from the reserved energy supply. General Service Instructions The following are general service instructions which must be followed in order to properly repair the vehicle and return it to its original integrity: • Do not expose inflator modules to temperatures above 65°C (150°F). • Verify the correct replacement part number. Do not substitute a component from a different vehicle. • Use only original GM replacement parts available from your authorized GM dealer. Do not use salvaged parts for repairs to the SIR system.

Related entry:

coil cam plate replacement cost cobalt, sir fuse location 2007 corvette,

2003 Cadillac Escalade Seat Replacement – Front Bucket Removal Procedure

0

Filed Under (Cadillac) by admin on 06-07-2010

download
Caution: Refer to SIR Caution in Service Precautions. 1. If equipped with side air bags, disable the SIR system. Refer to SIR Disabling and Enabling Zone 7 and SIR Disabling and Enabling Zone 9 in SIR. 2. Move the seat to the full rearward position. Remove the front seat nut cover (3), if equipped. 3. Remove the seat retaining front nuts (2). 4. Move the seat to the full forward position in order to remove the seat retaining rear bolts (1). 5. Disconnect the electrical harness, if equipped. 6. Remove the seat from the vehicle. Installation Procedure 1. Position the seat in the vehicle. 2. Connect the electrical harness, if equipped. Notice: Refer to Fastener Notice in Service Precautions. 3. Move the seat to the full forward position in order to install the seat retaining rear bolts (1). Tighten the retaining rear bolts to 55 N.m (41 lb ft). 4. Install the front seat adjuster bolt cover (3), if equipped. 5. Move the seat to the full rearward position and install the seat retaining front nuts (2). Tighten the nuts to 55 N.m (41 lb ft). 6. If equipped with side air bags, enable the SIR system. Refer to SIR Disabling and Enabling Zone 7 and SIR Disabling and Enabling Zone 9 in SIR.

2002 Chevy C 1500 Engine Controls – Spark Knock/MIL ON/ DTC P0332 Set

0

Filed Under (Chevrolet) by admin on 03-09-2010

download
Subject: Audible Spark Knock (Detonation), MIL Illuminated, DTC P0332 Set (Replace Rear Bank Knock Sensor and RTV Area Around Sensor) Models: 1998-2002 Chevrolet Camaro, Corvette 1998-2002 Pontiac Firebird with 5.7L Engine (VIN G – RPO LS1) 1999-2002 Chevrolet Silverado, Suburban, Tahoe 2002 Chevrolet Avalance 1999-2002 GMC Sierra, Yukon, Yukon XL 2002 Cadillac Escalade, Escalade EXT with 4.8L, 5.3L or 6.0L Engine (VINs V, T, Z, N, U – RPOS LR4, LM7, L59, L09, L04) This bulletin is being revised to add Cadillac Escalade and Cadillac Escalade EXT to the Models. Please discard Corporate Bulletin Number 02-06-04-023 (Section 6 – Engine/Propulsion System). Condition Some customers may comment on a mild to severe engine ping (commonly referred to as spark knock), usually worse during acceleration and/or an illuminated MIL. Upon investigation, the technician may find DTC P0332 set. Cause This condition may be the result of corrosion of the rear bank knock sensor due to water intrusion into the sensor cavity. This condition is more apparent on vehicles in which customers frequently wash the engine compartment

Related entry:

how much freon does 2002 chevy avalanche hold, how much freon does an 2004 avalance hold, changing the ac belt on a 2002 silverado, capacity specs for refrigerant system for chevy vin 3gnec16to1g252517, Blown Cigarette Lighter Fuse 2002 silverado, 2002 yukon proper ac pressure, 2002 mpv knock sensor replacement video, 2002 jaguar x type knock sensor location, torque specs for 2002 chevy tracker tensioner, 2002 chevy malibu horn switch replacement,

1999-2003 Chevrolet Silverado Revised Steering Wheel Position Sensor or Steering Shaft Lower Bearing Replacement Procedure and Steering Wheel Position Sensor Centering Procedure

0

Filed Under (Chevrolet) by admin on 17-01-2011

download
revise the Steering Wheel Position Sensor or Steering Shaft Lower Bearing Replacement procedure in the Variable Effort Steering (1998-2001 model years) or Steering Wheel and Column (2002-2003 model years) and add the Steering Wheel Position Sensor Centering procedure in the Steering Wheel and Column sub-sections of the Service Manual. Please replace the current information in the Service Manual with the following information. The following information has been updated within SI. If you are using a paper version of this Service Manual, please make a reference to this bulletin on the affected page. Steering Wheel Position Sensor or Steering Shaft Lower Bearing Replacement Removal Procedure Caution: Refer to SIR Caution in Cautions and Notices. 1. Disable the SIR system. Refer to SIR Disabling and Enabling Zone 3 in SIR. 2. Remove the steering column from the vehicle. Refer to Steering Column Replacement. 3. Remove the following from the steering shaft: 3.1. steering shaft seal (7) 3.2. sensor retainer (6) 3.3. steering wheel position sensor (5), refer to Steering Wheel Position Sensor Centering. 3.4. 2 lower spring retainers (4) 3.5. lower bearing spring (3) 3.6. lower bearing seat (2) 3.7. adapter and bearing assembly (1) Installation Procedure

Related entry:

chevy cavalier steering pivot pins, remove steering wheel 2008 vue, 2008 satrun vue steering column how install, which direction to unscrew axle nut on mercedes vito fornt wheels, replaceing steering wheel position sensor 2011 silverado pick up, lower steering column bearing removal 2004 chevrolet 2500hd, how to change lower radiator hose on a 1999 ford contour 2 0 motor, h2 hummer steering angle sensor replace, Adjusting Steering Wheel Position, 2011 sierra steering wheel sensor replacement,

Audi A4 Sedan 2002-2004, Audi A4 Avant 2002-2004, Audi A4 Cabriolet 2003-2004 – 1.8 Liter 4-Cyl. 5V Turbo Generic Scan Tool

0

Filed Under (Audi) by admin on 15-09-2009

Check the following wire connection for open circuit according to wiring diagram:Relay carrier in E-box, plenum chamber, position 3Terminal Harness connector atignition coils Terminal 8 1 Specified value: Wire resistance max 1.5 – If necessary, repair wire connection. Audi A4 Sedan 2002-2004, Audi A4 Avant 2002-2004, Audi A4 Cabriolet 2003-2004 – 1.8 Liter 4-Cyl. 5V Turbo Generic Scan Tool, Engi…Page 5 24-158 If no malfunctions are found in wires: – Check voltage supply of Motronic Engine Control Module (ECM) voltage supply relay – J271 – Page 24-158 . – Check activation of Motronic Engine Control
Module (ECM) voltage supply relay – J271 – Page 24-159 . Checking voltage supply If specified value is not obtained:
- Connect multimeter for voltage measurement as follows. Relay carrier in E-box, plenum chamber, position 3
Terminal

Related entry:

mitsubishi endeavor 2004 repair manual, audi 500 sel workshop manual, 2004 mercedes c320 fuse box chart pdf, 2004 suburban add freon, 2003 audi a4 a/c plentum drain location, bleed brakes in 2004 jeep liberty, 1993 audi quattro100 cs nanule, 1993 audi quattro 100 cs manual for free, where to recharge ac on 2004 impala diagram, 03 liberty dash removal,