e46 remove under dash panel
You are searching repair manual in PDF format about e46 remove under dash panel use another keyword for search another post or files
Filed Under (Ford) by admin on 06-03-2011
1. Disconnect battery ground cable (14301) . 2. Remove two console armrest mounting access covers (047A62) at rear of console panel (045A36) (snaps out) to gain access to armrest retaining bolts. 3. Remove four armrest-to-floor bracket retaining bolts and remove armrest assembly (snaps out of console). 4. Remove console panel gear shift plate (044G24) (snaps out). On vehicles equipped with manual transmissions, shift boot is attached to bottom of finish panel. Remove shift knob and slide boot and console panel gear shift plate up shift lever to remove. 5. To remove top finish panel position emergency brake lever in the UP position. Remove four retaining screws and lift top finish panel up. Disconnect necessary wire connectors. 6. Remove two console-to-rear floor bracket retaining screws. 7. Insert a small screwdriver into two notches at bottom of front upper finish panel and snap out. 8. If the vehicle has a radio chassis (18806) , the radio chassis must be removed. Refer to Section 15-01. If the vehicle doesn’t have a radio chassis , use a small screwdriver and pry radio cover finish panel out of console. 9. Flex glove compartment bin tabs inward. Drop down glove compartment (06010) assembly. Remove two console-to-instrument panel retaining screws. 10. Remove four console bracket retaining screws. Remove console panel from vehicle. 11. Remove three bolts retaining steering column opening cover (3A673) and reinforcement panel. Remove cover. 12. Remove steering column opening reinforcement by removing two bolts. 13. Remove two bolts retaining steering column opening reinforcement and remove reinforcement. 14. Remove six steering column retaining nuts (two retaining the hood release mechanism and four retaining column to lower brake pedal support). Lower steering column to floor. 15. Remove upper and lower steering column shrouds (3530) and disconnect wiring from turn signal and windshield wiper switch (13K359) . 16. Remove steering column through bolt and nut on engine compartment side of cowl panel. Remove steering column from vehicle. 17. Remove brake pedal support nut. 18. Snap out instrument panel defroster opening grille (044E82) . 19. Remove screws from speaker covers. Snap out speaker covers. 20. Remove front screws retaining RH and LH scuff plates at cowl side trim panels. 21. Remove RH and LH cowl side trim panels. 22. Disconnect wiring at RH cowl side. 23. Remove cowl side retaining bolts (one each side). 24. Remove five cowl top screws attachments. 25. Gently pull instrument panel (04320) away from RH side of cowl panel. Disconnect speedometer cable, air conditioning controls and wire connectors. 26. Place a drain pan or suitable container under the heater water hose connections at the cowl panel. 27. Disconnect heater water hoses (18472) from heater core tubes and plug heater water hoses with suitable 5/8-inch and 3/4-inch plugs. Cap heater core tubes to prevent coolant loss from heater core (18476) during removal of heater case. 28. Remove screw retaining A/C evaporator case support bracket (19A639) to cowl top panel. 29. Disconnect vacuum supply supply hose (black) from A/C vacuum supply in engine compartment. 30. Working under the hood (16612) , remove nut retaining heater case to cowl panel. 31. Inside passenger compartment, remove screw retaining A/C evaporator case mounting bracket (19A865) to cowl top panel. 32. Remove one screw retaining A/C evaporator case mounting bracket below heater case to cowl panel. 33. Carefully pull heater case from cowl panel and remove heater case assembly from vehicle. 34. To install, reverse Removal procedure. Check operation of all components. 35. After repairs have been completed, check the coolant level in the radiator (8005) and in the radiator coolant recovery reservoir (8A080) . Fill as required with the recommended coolant mixture.
Filed Under (Dodge) by admin on 17-08-2010
NOTE: Before starting this procedure, be certain to turn the steering wheel until the front wheels are in the straight-ahead position. 1. 2. 3. 4. 5. Disconnect and isolate the battery negative cable. Remove the trim from the right and left front door sills. Remove the trim from the left and right cowl side inner panels. Remove the steering column opening cover from the instrument panel. See: Steering Column Opening Cover and Knee Blocker Replacement Remove the two screws that secure the inside hood latch release handle to the instrument panel lower reinforcement and lower the release handle to the floor. Disconnect the driver side airbag module wire harness connector from the instrument panel wire harness at the instrument panel lower reinforcement. If the vehicle is so equipped, disconnect the overdrive lockout switch wire harness connector from the instrument panel wire harness near the instrument panel lower reinforcement. Remove the steering column from the vehicle, but do not remove the driver side airbag module, the steering wheel, or the switches from the steering column. Be certain that the steering wheel is locked and secured from rotation to prevent the loss of clockspring centering. Refer to Steering and Suspension/Steering/Steering Column/Service and Repair. See: Steering and Suspension/Steering/Steering Column/Service and Repair From under the driver side of the instrument panel, perform the following: a. Remove the screw from the center of the headlamp and dash to instrument panel bulkhead wire harness connector and disconnect the connector. b. Disconnect the two body wire harness connectors from the two instrument panel wire harness connectors that are secured to the outboard side of the instrument panel bulkhead connector. c. Disconnect the three wire harness connectors (one from the body wire harness, and two from the headlamp and dash wire harness) from the three junction block connector receptacles located closest to the dash panel. d. Unsnap the plastic retainer clip that secures the park brake release linkage rod to the lever on the back side of the park brake release handle and disengage the linkage rod end from the lever on the handle. e. Disconnect the instrument panel wire harness connector from the stop lamp switch connector receptacle. f. Disconnect the vacuum harness connector located near the left end of the heater-A/C housing. Remove the center support bracket from the instrument panel. See: Instrument Panel Center Support Bracket Replacement Remove the screw that secures the instrument panel wire harness ground eyelets to the left side of the Airbag Control Module (ACM) mount on the floor panel transmission tunnel. Disconnect the instrument panel wire harness connector from the ACM connector receptacle. Remove the glove box from the instrument panel. Refer to Body and Frame/Interior Trim/Glove Compartment/Service and Repair. See: Glove Compartment/Service and Repair Reaching through the instrument panel glove box opening, perform the following: a. Disconnect the two halves of the radio antenna coaxial cable connector near the center of the lower instrument panel glove box opening. b. Disengage the antenna half of the radio antenna coaxial cable from the retainer clip near the outboard side of the lower instrument panel glove box opening. c. Disconnect the blower motor wire harness connector located near the heater-A/C housing support brace on the inboard side of the instrument panel glove box opening. From under the passenger side of the instrument panel, perform the following: a. If the vehicle is so equipped, disconnect the two instrument panel wire harness connectors from the Infinity speaker amplifier connector receptacles on the right cowl side inner panel. b. Remove the nut that secures the instrument panel wire harness radio ground eyelet to the stud on the right cowl side inner panel. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15.
Filed Under (Mitsubishi) by admin on 30-12-2010
Disassembly (Ram-50) 1) Remove both 4WD indicator switches and steel balls. Remove speedometer gear assembly. Remove output shaft cover, gasket, wave spring and spacer. See Fig. 3. Remove rear cover, rear cover gasket and spacer from chain cover. Drive roll pin out of high-low shift fork. 2) Remove 2 seal plugs. Remove 2 poppet springs and steel balls. Shift transfer case to “4WD” and pull high-low shift rail out, in rear cover direction. Remove interlock plunger. Remove pulse generator (if equipped), front output shaft cover and pulse rotor (if equipped). Remove snap ring from rear bearing on output shaft. Remove chain cover, oil guide and side cover. Remove countershaft locking plate. Remove countershaft. 3) Remove countergear, 2 thrust washers, 2 needle bearings and spacer through side cover opening. Remove snap ring, spring retainers and spring from 2WD-4WD shift rail. Remove front output shaft, rear output shaft and chain as assembly. 4) Remove 2WD-4WD shift fork and distance piece. Drive out 2WD-4WD shift rail spring pin. Remove 2WD-4WD shift rail and lug. Remove high-low shift fork and high-low synchronizer sleeve. Remove needle bearing and snap ring from input gear. Remove input gear assembly. 5) If either control shaft or input gear oil seals are to be replaced, drive out roll pin from transmission control change shifter. Separate transfer case from adapter. See Fig. 3. Disassembly (Montero) 1) Remove dynamic damper, 5 detection switches and 3 steel balls. Remove poppet plug, spring and steel ball. Remove speedometer gear assembly. Remove output shaft rear cover, spacers, dust seal guard and oil seals. Front output shaft cover, wave spring and spacer (if equipped). 2) Remove high-low shift rail plug and high-low shift fork spring pin. Shift transfer case to “4WD”. Remove rear cover and high- low shift rail. Remove interlock plunger. Remove rear output shaft (viscous coupling) assembly and center differential assembly. Remove 2WD-4WD synchronizer assembly, chain and front output shaft from transmission as a unit. With White paint make match marks in grooves of 2WD-4WD synchronizer in 3 places. With White paint make match marks on spline projections of 2WD-4WD synchronizer sleeve in 3 places. Refer to match marks during reassembly. 3) Remove snap ring, spring seat, spring, 2WD-4WD shift fork and 2WD-4WD synchronizer sleeve. Remove differential lock hub, oil dam cover and bearing retainer. Remove side cover and gasket. Remove transfer counter gear shaft, transfer counter gear, thrust washer, needle bearings and spacer. Remove transfer drive shaft assembly. Remove high-low shift fork assembly and clutch sleeve. Remove transfer input gear assembly. 4) Remove 2WD-4WD shift lug spring pin, spring, spring retainer 2WD-4WD shift lug and shift rail. Remove input gear oil seal, baffle plate, dust seal guard and front output shaft oil seal. See Fig. 4.
Filed Under (Cadillac) by admin on 14-07-2010
REMOVAL PROCEDURE 1. Remove the I/P trim panel. CAUTION: Refer to Battery Disconnect Caution in Service Precautions. Refer to SIR Caution in Service Precautions . 2. Remove the center console, if equipped. 3. Disconnect the negative battery cable. 4. Remove the driver side knee bolster. 5. Remove the lower I/P trim panel. 6. Remove the passenger side air bag module. 7. Remove the radio. 8. Remove the HVAC control. 9. Remove the accessory switch housing. 10. Remove the left air louver housing. 11. Remove the steering column. 12. Remove the CIM, if equipped. 13. Remove the remote control door lock receiver module, if equipped. 14. Remove the data link connector from the I/P. 15. Remove the park brake release lever from the I/P. 16. Remove the I/P cluster. 17. Remove both front window air duct from the I/P assembly. 18. Remove the harness from the I/P. 19. Remove the I/P assembly retaining nuts (4) and bolts (3). 20. Remove all harness hold down retainers from the I/P assembly. 21. Remove the I/P assembly from the vehicle. 22. Remove the I/P upper brackets. 23. Disconnect all the electrical connectors from the wiring harness junction block. 24. Remove the transfer case control module from the bracket, if equipped. 25. Remove the antenna cable from the cross car duct. 26. Remove the cross car duct. 27. Remove the amplifier, if equipped.
Filed Under (Dodge) by admin on 20-09-2010
Trim Panel: Service and Repair REMOVAL 1. Using a trim stick (C-4755), pry courtesy lamp from door trim. 2. Disconnect wire connector from courtesy lamp. 3. If equipped, remove screws attaching door assist handle to inner door panel. 4. If equipped, remove screw attaching door pull cup to inner door panel. 5. If equipped, remove screws attaching trim panel to door from below map pocket. 6. If equipped, remove window crank. 7. Using a trim stick, remove screw cover from switch panel. 8. Remove screws attaching switch panel to door trim. 9. Remove power accessary switch from door trim. 10. Disconnect power switch from wire connector. 11. If equipped, using a small, flat bladed pry tool, remove memory seat/mirror switch and disconnect wire connector. 12. If equipped, remove screw holding door trim to door panel from behind inside latch release handle. 13. Disengage clips attaching door trim to door frame around perimeter of panel. 14. Lift trim panel upward to disengage flange from inner belt molding at top of door. 15. Tilt top of trim panel away from door to gain access to latch linkage. 16. Disengage clip attaching linkage rod to inside latch release handle. 17. Separate linkage rod from latch handle. 18. Remove front door trim panel from vehicle. INSTALLATION 1. Hold top of trim panel away from door to gain access to latch linkage. 2. Place linkage rod in position on latch handle. 3. Engage clip to hold linkage rod to inside latch release handle. 4. Place front door trim panel in position on door. 5. Install trim panel into inner belt molding at top of door. 6. Install clips to attach door trim to door frame around perimeter of panel. 7. If equipped, install screw to attach door trim to door panel behind inside latch release handle. 8. If equipped, connect power switch into wire connector. 9. Place power accessary switch in position on door trim. 10. Connect wire connector into memory seat/mirror switch and install switch into trim panel. 11. Install screws to attach accessary switch panel to door trim. 12. Install screw cover into switch panel. 13. If equipped, install window crank. 14. If equipped, install screws to attach trim panel to door inside map pocket. 15. If equipped, install screw to attach door pull cup to inner door panel. 16. If equipped, install screws to attach door assist handle to inner door panel. 17. Connect wire connector into courtesy lamp. 18. Install lamp in door trim.