Auto Repair Manual Free Download and ReviewsFree download ebook pdf files automotive manual

download
Some 1997-2008 vehicles equipped with a 4.6L 2V, 5.4L 2V, or 6.8L 2V engine and aluminum cylinder heads may experience a spark plug port with stripped or missing threads. ACTION Follow the Service Procedure steps to correct the condition for non warrantable repairs. SERVICE PROCEDURE Ford Motor Company now authorizes LOCK-N-STITCH aluminum insert and tool kit as a proper repair procedure. Follow the procedure included in the tool kit for using the tools and inserts. Tool kits and inserts can be ordered from Rotunda by calling 1-800-Rotunda (768- 8632). Choose option two (2), part number 302-00001. NOTE FORD MOTOR COMPANY HAS DETERMINED THAT REPAIRS MADE WITH THESE ALUMINUM INSERTS AND LOCK-N-STITCH TOOLS DO NOT AFFECT THE HEAT TRANSFER FUNCTION BETWEEN THE SPARK PLUG AND THE CYLINDER HEAD.

download
ENGINE – 4.0L OHV – CARBON KNOCK ON ACCELERATION NOISE – CARBON KNOCK ON ACCELERATION – VEHICLES EQUIPPED WITH 4.0L OHV ENGINE ONLY FORD: 1990-1997 AEROSTAR 1990-2000 EXPLORER, RANGER ISSUE Some vehicles equipped with the 4.0L OHV engine may exhibit an engine noise which may be perceived by the customer as a piston/connecting rod bearing knock. This carbon knock is heard only under load during the drive cycle. Carbon knock is a customer drive duty-cycle phenomenon that cannot be repaired with an engine exchange. This may be caused by carbon build-up within the combustion chamber. ACTION Verify condition. If normal diagnostics fail to correct the condition, de-carbon the combustion chamber to help quiet the carbon knock noise. Refer to the following Service Procedure for details. SERVICE PROCEDURE Use Motorcraft Carburetor Tune-up Cleaner PM-3. Carbon removal: a. Disconnect canister purge line from throttle body. b. Attach a vacuum line to the canister purge port. c. At hot engine idle, allow the engine to ingest 1/2 to 2/3 of a can of Motorcraft Carburetor Tune-up Cleaner. Use caution not to ingest too quickly due to potential hydro-lock issues. d Shut engine off and allow it to soak for one hour. e. Start engine, allow engine to ingest the remainder of the Motorcraft Carburetor Tune-up Gleaner. f. Remove vacuum line and re-install canister purge line. g. Road test vehicle at 3500 RPM for 2-3 miles. h. Repeat above procedure two times for a total of three times. i. Change oil and filter.

repair and service manual covers Ford 2WD and 4WD full-size F-150 (gasoline) 1997-2003, Expedition 1997-2002 (gasoline), F-250 1997-1999, and Lincoln Navigator 1998-2002. Note: this manual does not include diesel engine, F-250 HD, Super Duty, F-350, or Lightning models.
What’s Inside
* Introduction: Vehicle identification numbers; Buying parts; Maintenance techniques, and more.
* Tune-up and routine maintenance
* V6 engine
* V8 engines
* Engine and overhaul procedures
* Cooling, heating and air-conditioning systems
* Fuel and exhaust systems

repair and maintenance manual covers all US and Canadian models of Ford F-150 and F250 pick-ups (except Super Duty); Ford Expedition, and Lincoln Navigator, 2- and 4-wheel drive with gasoline engines, from 1997 through 2002.
Note: this manual does not include information specific to Lightning models.
Introduction: About this manual | Introduction | Vehicle identification numbers | Maintenance techniques, tools and working facilities | Buying parts | Jacking and towing | Anti-theft audio system | Booster battery (jump) starting | Conversion factors | Automotive chemicals and lubricants | Safety first! | Troubleshooting
* Tune-up and routine maintenance
* V6 engine, V8 engines, general engine overhaul procedures
* Cooling, heating and air-conditioning systems
* Fuel and exhaust systems
* Engine electrical systems
* Emissions and engine control systems
* Manual transmission, automatic transmission, transfer case
* Clutch and driveline
* Brakes
* Suspension and steering systems
* Body
* Chassis electrical system
* Wiring diagrams

download
Engine Front Cover If the engine front cover (6019) is being removed to check timing chain deflection, refer to Timing Chain Deflection Procedure as outlined in Section 03-00. SPECIAL SERVICE TOOL(S) REQUIRED Description Crankshaft Damper Remover Vibration Damper and Seal Replacer T82L-6316-A Vibration Damper Remover Adapter Removal 1. Remove engine (6007) from vehicle. Refer to procedure in this section. 2. Loosen drive belt tensioner (6B209) and drive belt (8620) . 3. Remove water pump pulley retaining bolts and water pump pulley (8509) . 4. Remove retaining bolts and disconnect heater water outlet tube (18663) from water pump (8501) . 5. Disconnect electrical connector at camshaft position sensor. 6. Disconnect electrical connector at crankshaft position sensor (CKP sensor) (6C315) . 7. Remove retaining bolt and disconnect radiator lower hose tube (8291) from water pump . NOTE: If the vibration damper and crankshaft pulley have to be separated, mark the vibration damper and crankshaft pulley so that they may be reassembled in the same relative position. This is important as the vibration damper and crankshaft pulley are initially balanced as a unit. NOTE: If the vibration damper is being replaced, check if the original vibration damper has balance pins installed. If so, new balance pins (6A328 or equivalent) must be installed on the new vibration damper in the same position as the original vibration damper. The crankshaft pulley (new or original) must also be installed in the same relative position as originally installed. 8. Remove crankshaft pulley (6312) and vibration damper assembly using Crankshaft Damper Remover T58P-6316-D and Vibration Damper Remover Adapter T82L-6316-B. 9. Remove four retaining bolts and remove brace from A/C bracket and P/S bracket. 10. Remove oil bypass filter (6714) . Tool Number T58P-6316-D T82L-6316-B CAUTION: The engine front cover cannot be removed without lowering the oil pan (6675) . 11. Remove oil pan . Refer to procedure in this section. CAUTION: Do not overlook the engine front cover retaining bolt located behind the oil pump and filter body (6603) . The engine front cover will break if pried upon and all retaining bolts are not removed. 12. Remove engine front cover retaining bolts. It is not necessary to remove water pump . 13. Remove engine front cover and water pump as an assembly. 14. Remove engine front cover gasket and discard. Water Pump Tightening Sequence Installation NOTE: Lightly oil all bolt and stud bolt threads before installation except those specifying special sealant. 1. Clean gasket surfaces on the engine front cover and cylinder block (6010) . If reusing the engine front cover , replace crankshaft front seal (6700) . Refer to Crankshaft Pulley and/or Damper and/or Crankshaft Front Seal in this section. 2. If a new engine front cover is to be installed: Install oil pump and filter body . Clean water pump gasket surface. Position a new water pump housing gasket (8507) on the engine front cover and install water pump . Install water pump retaining bolts. Tighten to 20-30 Nm (15-22 lb-ft). 3. Lubricate crankshaft front seal with clean engine oil XO-10W30-QSP or -DSP or equivalent meeting Ford specification ESE-M2C153-E. NOTE: Gasket and Trim Adhesive D7AZ-19B508-B or equivalent meeting Ford specification ESE-M2G52-A is recommended to hold the engine front cover gasket (6020) in position while the engine front cover is installed. 4. Position a new engine front cover gasket on the cylinder block and install the engine front cover / water pump assembly using dowels for proper alignment. 5. Install the engine front cover retaining bolts. Tighten to 20-30 Nm (15-22 lb-ft). Install the capscrew (Part No. N804841) nearest the oil bypass filter flange last, and tighten last. Apply Loctite® or equivalent to bolt prior to installation. Refer to illustration under Step 13 of removal procedure. 6. Install oil pan as outlined. 7. Install oil bypass filter . 8. Coat pulley sealing surface with clean engine oil XO-10W30-QSP or -DSP or equivalent meeting Ford specification ESE-M2C153-E. NOTE: When using silicone rubber sealer, assembly must occur within 15 minutes after sealer application. After this time, the sealer may start to setup, and its sealing effectiveness may be reduced. 9. Apply a small amount of Silicone Gasket and Sealant F1AZ-19562-A or equivalent meeting Ford specification WSE-M4G320-A2 to crankshaft keyway. 10. Position crankshaft key (6B316) in the crankshaft keyway.