fixing a gear lever in 2011 ford transit


You are searching repair manual in PDF format about fixing a gear lever in 2011 ford transit use another keyword for search another post or files



  fixing a gear lever in 2011 ford transit Direct Download speed 5787 Kb/s

  fixing a gear lever in 2011 ford transit Full Version speed 6767 Kb/s




2006 Ford Explorer 6R60 Transmission Selector Lever Cable REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 07-05-2011

download
Selector Lever Cable Vehicles Equipped with a 6R60 Transmission Removal All vehicles 1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section 100-02. 3. With the selector lever in PARK, disconnect the selector lever cable from the selector lever. Vehicle equipped with a 6R60 transmission 6. Remove the cable shield by prying on the shield closest to the boot, then sliding the shield away from the boot. 4. Disconnect the selector lever cable from the selector lever housing. 7. Unlock the lock tab and disconnect the selector lever cable end from the transmission manual lever. 5. Pull the cable and grommet through the floorpan. 8. Disconnect the selector lever cable from the bracket and remove the cable. Vehicles equipped with a 5R55S transmission 9. Remove the cable shield by prying on the side of the shield closest to the boot, then sliding the shield away from the boot. 10. Unlock the lock tab and disconnect the selector lever cable end from the transmission manual lever. 11. Disconnect the selector lever cable from the bracket and remove the cable. Installation Vehicles equipped with a 6R60 transmission 1. Install the selector lever cable into the bracket. 2. Connect the selector lever cable end onto the transmission manual lever and lock the lock tab. 3. NOTE: If the shield is loose, install a new shield. Install the cable shield. Vehicles equipped with a 5R55S transmission 4. Install the selector lever cable into the bracket. 5. Connect the selector lever cable end onto the transmission manual lever.

Related entry:

how to install 4wd selector on 2006 envoy denali, bmode in mirage, changing transmission selector cable in hummer, gear shift lever on 2005 Pacifica, how to replace the 4wd selector knob on an 2006 gmc envoy xl, hummer h2 shifter cable replacement removal, porsche 928 selector light, relay lever cable carrier how to replace in a 1999 vw beetle,

Ford / Mercury / Lincoln Band-Mounted Sensor Re-Learn Instructions

0

Filed Under (Ford, Lincoln) by admin on 17-10-2009

The instructions below can be used for the following vehicles: 2008 Ford Crown Victoria / Lincoln Town Car / Mercury Grand Marquis 2008 Ford E-series 2007-2009 Ford Edge / Lincoln MKX 2005-2008 Ford Escape / Mercury Mariner 2007-2009 Ford Expedition / Lincoln Navigator 2006-2009 Ford Explorer / Lincoln Aviator / Mercury Mountaineer 2007-2008 Ford F150, F250, and F350 / Lincoln Mark LT
2009 Ford Flex 2008-2009 Ford Focus 2006-2007 Ford Freestar / Mercury Monterey 2008-2009 Ford Fusion / Lincoln MKZ / Mercury Milan 2007-2009 Ford Mustang 2007-2009 Ford Ranger 2008-2009 Ford Taurus / Mercury Sable

1. Make sure all tires are inflated to the vehicle’s recommended inflation pressures (found in the owner’s manual on the door placard). 2. Turn the ignition switch to OFF then press and release the brake pedal. 3. Turn the ignition switch from OFF to RUN (engine OFF) 3 times, ending in the RUN position. Do this within 10 seconds. 4. Press and release the brake pedal

download

Related entry:

1997 Lincoln Repair Manual Free, front end ailgment on a murcury mountaineer awd 2000, ford f 150 204 buskarkomoponer kadena de tiempo en tiempo, repair heated seats 2005 freestar, where is the horn of 1998 ford escort, 2010 ford f150 actuator recalibration, repair manuel on line for a ford mustang 4 0 V6 2007, yhs-playfree, 93 ford festiva free car repair manuel, 97 escort tv cable adjustment,

2006 Pontiac GTO Transmission Jumps Out of Gear

0

Filed Under (Pontiac) by admin on 31-10-2010

download
If the transmission jumps out of gear during deceleration, inspect the components that may allow for the gears or shafts to tip. If the gears or shafts tip, the synchronizer sleeve can disengage from the selector teeth on the speed gear. If the transmission jumps out of gear during acceleration, inspect the components that may not allow full engagement of the synchronizer sleeve to the selector teeth on the speed gear. Insufficient engagement of the selector teeth under torque may cause the transmission to jump out of gear. Test Description The numbers below refer to the step numbers on the diagnostic table. 2. A static shift test is performed by shifting into all gear positions with the engine not operating. While performing the test, slowly move the shift lever. Feel for proper movement of the shift lever and transmission internal shift components. 4. A dynamic shift test is performed by shifting into all gear positions with the engine operating. Test for the correct mesh of the synchronizers sleeve and the speed gear selector teeth. Move the shift lever, and feel for the synchronizer sleeve to release from the gear, then let up on the clutch pedal. Depress the clutch pedal and move the shift lever to engage the gear again, to ensure full travel of the shift components. 5. This step inspects for worn or damaged transmission or engine mounts. Loose mounts may cause a shock on the transmission allowing for gear disengagement. 6. This step inspects for the misalignment of the torque tube to transmission. Misalignment may put a bind on the input shaft, allowing for the input shaft or the mainshaft to tip. 8. This step inspects the pilot bearing and the pilot bearing journal on the input shaft. A worn pilot bearing or input shaft may allow the input shaft to tip, causing gear disengagement.

Related entry:

2001 dodge avenger gear shift stuckin second gear, 2010 aveo cam gear, types of gears diagram,

1997 Ford Explorer/Mountaineer Transmission ASSEMBLY

0

Filed Under (Ford) by admin on 06-04-2011

download
1. Thoroughly clean the transmission case and extension housing in solvent and blow dry with compressed air. 2. Inspect the transmission case for the following: 1. Stripped bolt hole threads. 2. Gasket and mating surfaces for burrs or nicks. 3. Obstructions to vent and fluid passages. Cracks or warpage. 3. Inspect the extension housing for cracks, burrs or warpage. 4. Inspect case bearing for damage. Replace as needed. 5. Remove the case bearing. 1. Install the Bearing Cup Puller with Slide Hammer into case bearing. 2. Remove the case bearing. Use an oil stone to remove any nicks or burrs in the bearing case bore. 6. Install a new case bearing. 1. Assemble and install the Drive Handle and Bearing Installer. 2. Position new case bearing onto bearing installer tool. 7. Tap case bearing into case bearing bore. 8. Install the A4LD Holding Fixure Adapter. 1. Position the A4LD Holding Fixture Adapter on the rear of the transmission case. 2. Install the A4LD Holding Fixture Adapter bolts. 9. Attach the fixture arm of the Bench Mounted Holding Fixture to the A4LD Holding Fixture Adapter. 10. Install transmission into Bench Mounted Holding Fixture. Rotate the transmission so that the fluid pan rail is facing up. -MOUNTED HOLDING FIXTURE IS SECURE. 11. Using Shift Lever Seal Replacer, install the manual control lever shaft seal. Lubricate the manual control lever shaft seal with petroleum jelly. 12. Assemble the manual valve inner lever and parking lever actuating rod as shown. 13. Install the manual control lever shaft. 14. NOTE: Align the manual control lever shaft alignment groove with the manual control lever shaft spring pin bore in the transmission case. Install the manual control lever shaft spring pin. Tap the manual control lever shaft spring pin into the transmission case. 15. Install the manual valve inner lever and parking lever actuating rod on to the manual control lever shaft. 16. Install the manual valve inner lever nut on the manual control lever shaft and tighten. 17. Install the output shaft thrust washer (No. 11). Coat the output shaft thrust washer with petroleum jelly. 18. Install the park gear.

Related entry:

1996 ranger manual transmission gear shift lever bolt, blue point cam bearing installer parts, how to change 4r70w transmission manual control lever seal, SONATA AUTOMATIC GEAR REPAIR MANUAL,

1999 Ford Taurus Steering Gear Base REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 19-02-2011

download
1. Open hood. 2. Disconnect battery ground cable (14301). Refer to Section 14-01. 3. From inside vehicle, remove nuts retaining steering column tube boot (3C611) to cowl panel. 4. Remove bolt retaining steering column intermediate shaft coupling (3A525) to steering column lower yoke (3N725) . 5. Position steering column tube boot out of the way. Remove pinch bolt retaining steering column intermediate shaft coupling to power rack and pinion steering gear and remove steering column intermediate shaft coupling . 6. Raise vehicle on a twin post hoist and remove front wheel and tire assemblies. 7. Remove exhaust system flex tube-to-dual converter Y-pipe attachment. Disconnect heated oxygen sensor wiring harness. Remove dual converter Y pipe (5F250) from vehicle. Dual Converter Y Pipe Removal 8. Support vehicle with jack stands under rear edge of front sub-frame (5C145). 9. Remove tie rod cotter pins and nuts, and remove tie rod end (3A130) from RH front wheel knuckle (3K185) and LH front wheel knuckle (3K186). 10. Remove tie rod end from front wheel spindle tie rod (3280) . Mark position of jam nut to maintain alignment. 11. Remove nuts from steering gear-to-front sub-frame retaining bolts. 12. Remove rear sub-frame-to-body retaining bolts. 13. Raise twin post hoist carefully until rear sub-frame (5R003) separates from body approximately 102 mm (4 inches). 14. Remove heat shield push-pin retainers from power steering hose bracket (3C510). Remove steering shaft U-joint shield (3F540). 15. Remove screw and power steering left turn pressure hose (3A714) from power steering hose bracket . Remove two screws and power steering hose bracket. 16. Remove LH stabilizer bar link (5K484). 17. Disconnect power steering pressure switch electrical connector. 18. Rotate power rack and pinion steering gear to clear bolts from front sub-frame and pull left to ease line fitting removal. 19. Place a drain pan under vehicle and remove hydraulic power steering pressure hose and power steering return hose from fittings on power rack and pinion steering gear. 20. Remove power rack and pinion steering gear assembly through LH wheel well. Installation 1. Install new Teflon® O-rings on both line connector assemblies as described under Quick Connect Power Steering Fitting—Seal Replacement. 2. Place steering gear retaining bolts in steering gear housing (3548). 3. Install power rack and pinion steering gear through LH wheel well. 4. Install power steering hose bracket and two screws. Tighten to 9-12 Nm (80-106 lb-in). 5. Install hydraulic power steering pressure hose and power steering return hose to fittings on power rack and pinion steering gear. Tighten hoses to 33-41 Nm (25-30 lb-ft). 6. Install power steering pressure hose and and screw. Tighten to 9-12 Nm (80-106 lb-in). 7. Connect power steering pressure switch electrical connector. 8. Position power rack and pinion steering gear into front sub-frame. 9. Install tie rod ends onto front wheel spindle tie rods . 10. Install push-pin retainers at top of heat shield. 11. Install tie rod end to RHfront wheel knuckle and LH front wheel knuckle. Install nuts and tighten to 47-63 Nm (35-46 lb-ft). Install new cotter pins. 12. Install LH stabilizer bar link. Tighten to 76.5-103.5 Nm (57-76 lb-ft).

Related entry:

1995 ford explorer lower steering shaft, 2007 g5 pontiac intermediate steering shaft, 04 cts power steering tube, replace power seat gears 2005 town and country, reconnecting pinch bolt on rack and pinion on a 2004 cadillac deville, noise in rh front ford windstar, mazda 323f power steering cooling pipe, intermediate steering shaft for 2008 highlander, ford focas1 6 2003zetec how to replace the brake lever waning switch, diagram of 2002 lincoln continental front wheel drive rack and pinion,