ford explorer 2004 map sensor


You are searching repair manual in PDF format about ford explorer 2004 map sensor use another keyword for search another post or files



  ford explorer 2004 map sensor Direct Download speed 5787 Kb/s

  ford explorer 2004 map sensor Full Version speed 6767 Kb/s




1995 Ford Mustang Camshaft Position (CMP) Sensor Removal Installation

0

Filed Under (Ford) by admin on 08-02-2011

download
1. Disconnect battery ground cable (14301) . 2. Disconnect fuel charging wiring (9D930) from distributor stator (12A112) (camshaft position sensor). 3. Remove stator camshaft position sensor retaining screws and distributor stator (camshaft position sensor) from camshaft position sensor housing. 4. If removing camshaft position sensor housing from the engine front cover (6019) , proceed with Removal Step 5. If camshaft position sensor housing is not being removed, proceed to Installation Step 6. 5. CAUTION: Before proceeding with this procedure, set cylinder No. 1 to 26 degrees After Top Dead Center (ATDC) of the compression stroke. Then note the position of the stator (camshaft position sensor) electrical connector. The installation procedure requires that the connector be located in the same position. Remove retaining bolt and hold-down clamp (12270) . 6. NOTE: The oil pump intermediate shaft (6A618) should be removed with the camshaft position sensor housing. Remove camshaft position sensor housing from engine front cover . Installation 1. CAUTION: If the replacement distributor stator (camshaft position sensor) does not contain a plastic locator cover tool, a special service tool such as Syncro Positioning Tool T89P-12200-A must be obtained prior to installation of the replacement distributor stator (camshaft position sensor). Failure to follow this procedure will result in improper stator (camshaft position sensor) alignment. This will result in the fuel system being out of time with the engine, possibly causing engine damage. If the plastic locator cover tool is not attached to the replacement distributor stator (camshaft position sensor), attach Syncro Positioning Tool T89P-12200-A as follows: a. Engage camshaft position sensor housing vane into the radial slot of the tool. b. Rotate tool on camshaft position sensor housing until tool boss engages notch in camshaft position sensor housing. The cover tool should be square and in contact with entire top surface of camshaft position sensor housing. 2. Transfer oil pump intermediate shaft from old camshaft position sensor housing to replacement camshaft position sensor housing. 3. CAUTION: If stator (camshaft position sensor) electrical connector is not positioned properly (for example, contacting the A/C compressor bracket), DO NOT reposition the connector by rotating the camshaft position sensor housing. This will result in the fuel system being out of time with the engine, possibly causing engine damage. Remove the camshaft position sensor housing and repeat installation procedure, beginning with Step 1. Install camshaft position sensor housing so that drive gear engagement occurs when arrow on locator tool is pointed approximately 30 degrees counterclockwise from the front face of the cylinder block (6010) . This step will locate stator (camshaft position sensor) electrical connector in the pre-removal position. 4. Install hold-down clamp and retaining bolt and tighten bolt to 20-30 Nm (15-22 lb-ft). 5. Remove Syncro Positioning Tool T89P-12200-A. 6. CAUTION: If stator (camshaft position sensor) electrical connector is not positioned properly (for example, contacting the A/C compressor bracket), DO NOT reposition the connector by rotating the camshaft position sensor housing. This will result in the fuel system being out of time with the engine, possibly causing engine damage. Remove the camshaft position sensor housing and repeat installation procedure, beginning with Step 1. Install distributor stator (camshaft position sensor) and retaining screws. Tighten screws to 2.5-3.5 Nm (22-31 lb-in). 7. Connect fuel charging wiring connector to distributor stator (camshaft position sensor). 8. Connect battery ground cable .

Related entry:

95 cadillac conccourse cam sensor issue, cam positioning tool for 2002 landrover freelander 2 5 liter, lincoln aviator v-8 4 6 litre engine oxygen sensor locations, cam sensor 1991 cadillac seville, throttle position sensor for 2004 ford tarsus, 2002 kia rio temperature control sensor replacement, where are/abs sensors located on 2006 ford escape, where is cam sensor located on 2005 buick lacross?, IAT sensor on a 2007 ford expedition, how to replace oxygen sensor 2002 nissan quest,

1998 Ford Windstar Camshaft Position (CMP) Sensor REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 17-02-2011

download
CAUTION: Prior to removal of the camshaft position sensor (CMP sensor) (12126) , set cylinder No.1 to zero degrees top dead center (TDC) of compression stroke. Then note the position of the camshaft position sensor electrical connector. The installation procedure requires the connector be located in the same position. Removal 1. Disconnect battery ground cable (14301). Refer to Section 14-01. 2. Disconnect fuel charging wiring connector from camshaft position sensor. 3. Remove camshaft position sensor retaining screws and camshaft position sensor from camshaft position sensor housing. 4. If removing camshaft position sensor housing from the cylinder block (6010), proceed with Removal Step 5. If not removing camshaft position sensor housing, proceed to Step 6 of the installation procedures. 5. Remove hold-down clamp (12270) (bolt and washer assembly). 6. NOTE: Remove the oil pump intermediate shaft (6A618) with the camshaft position sensor housing. Remove camshaft position sensor housing from cylinder block. Installation 1. CAUTION: If the replacement camshaft position sensor housing does not contain a plastic locator cover tool, a special service tool must be obtained prior to installation of the replacement camshaft position sensor. Failure to follow this procedure will result in improper camshaft position sensor alignment. This will result in the ignition fuel system being out of time with the engine, possibly causing engine damage. NOTE: For 3.0L engines, use Syncro Positioning Tool 303-589. For 3.8L engines, use Syncro Positioning Tool 303-562 (T96T-12200-A). If the plastic locator cover tool is not attached to the replacement camshaft position sensor housing, attach syncro positioning tool as follows: a. Engage camshaft position sensor housing vane into the radial slot of the tool. b. Rotate tool on camshaft position sensor housing until tool boss engages notch in camshaft position sensor housing. 2. Transfer oil pump intermediate shaft from old camshaft position sensor housing to replacement camshaft position sensor housing. 3. Install camshaft position sensor housing so drive gear engagement occurs when arrow on syncro positioning tool is pointed approximately as shown in the illustrations. This step will locate camshaft position sensor electrical connector in the pre-removal position. 4. Install hold-down clamp (washer and bolt assembly) and tighten bolt to 20-30 Nm (15-22 lb-ft). 5. Remove syncro positioning tool. 6. CAUTION: If camshaft position sensor electrical connector is not positioned properly, DO NOT reposition the connector by rotating the camshaft position sensor housing. This will result in the fuel system being out of time with the engine, possibly causing engine damage. Remove the camshaft position sensor housing and repeat installation procedure, beginning with Step 1. Install camshaft position sensor and retaining screws. On 3.0L engine, tighten screws to 2.5-3.5 Nm (23-30 lb-in). On 3.8L engine, tighten screws to 4.5-7 Nm (40-61 lb-in). 7. Connect fuel charging wiring connector to camshaft position sensor. 8. Connect battery ground cable. Refer to Section 14-01. Camshaft Position Sensor—3.0L Engine

Related entry:

installing tps sensor on a ford escort, diagram camshaft position sensors for 2002 santa fe, como checar crankshaft posicion sensor rodeo isuzu 1998, what sensors on back of block 5 3, tcc on astor van, replacing tps in 1999 ford escort, how to adjust throttle position sensor 2002 escort, diagram of where low coolant sensor is on Northstar 4 0, 06 kia sorento camshaft positioning sensor, any reviews of ktc tools,

Ford / Mercury / Lincoln Band-Mounted Sensor Re-Learn Instructions

0

Filed Under (Ford, Lincoln) by admin on 17-10-2009

The instructions below can be used for the following vehicles: 2008 Ford Crown Victoria / Lincoln Town Car / Mercury Grand Marquis 2008 Ford E-series 2007-2009 Ford Edge / Lincoln MKX 2005-2008 Ford Escape / Mercury Mariner 2007-2009 Ford Expedition / Lincoln Navigator 2006-2009 Ford Explorer / Lincoln Aviator / Mercury Mountaineer 2007-2008 Ford F150, F250, and F350 / Lincoln Mark LT
2009 Ford Flex 2008-2009 Ford Focus 2006-2007 Ford Freestar / Mercury Monterey 2008-2009 Ford Fusion / Lincoln MKZ / Mercury Milan 2007-2009 Ford Mustang 2007-2009 Ford Ranger 2008-2009 Ford Taurus / Mercury Sable

1. Make sure all tires are inflated to the vehicle’s recommended inflation pressures (found in the owner’s manual on the door placard). 2. Turn the ignition switch to OFF then press and release the brake pedal. 3. Turn the ignition switch from OFF to RUN (engine OFF) 3 times, ending in the RUN position. Do this within 10 seconds. 4. Press and release the brake pedal

download

Related entry:

1997 Lincoln Repair Manual Free, Ford L9000 Service Manual, 1991 mercury capri repair manual, ford f-150 throttle body relearn, what size thermostat do you put in 1991 Lincoln Mark Vll 5 0 302 engine ?, how to take apart a harmonic balancer on a 2007 ford explorer, 2004 ford freestar location ac orfice tube, free hose diagram 1991 ford escort gt 1 8, 2008 ford taurus ac capacities, 2008 ford escape flex pipe,

2003-2006 Chevrolet Express Antilock Brake (ABS) Activation At Low Speeds (Clean Wheel Speed Sensor Mounting Surface)

0

Filed Under (Chevrolet) by admin on 25-01-2011

download
Condition Some customers may comment on ABS activation at low speeds, usually below 8 km/h (5 mph). Upon investigation, the technician will find no DTCs set. Cause The cause of this condition may be an increased air gap between the wheel speed sensor and the hub reluctor ring due to rust and debris built up on the sensor mounting surface. Correction Measure AC voltage and clean the wheel speed sensor mounting surfaces. 1. 2. 3. 4. Raise and support the vehicle. Disconnect both the front wheel speed sensor connectors at the frame and harness. Place a Digital Volt Meter (DVM) across the terminals of each wheel speed sensor connector. Rotate the wheel clockwise approximately one revolution per second. The minimum reading should be at least 350 ACmV’s. If the reading is less than 350 ACmV’s, remove the wheel speed sensor. 5. Plug the wheel speed sensor bore in order to prevent debris from falling into the hub during service. 6. Clean the wheel speed sensor mounting surface using a wire brush, sand paper, emery cloth, scotch brite, or other suitable material. Be sure to thoroughly clean the wheel speed sensor surface. There should be no rust or corrosion. 7. Check the sensor head to determine if it has been warped/distorted due to the corrosion build up or other causes. Check the mounting surface on the sensor head for flatness by placing it on the edge of a metal machinists scale or other suitable straight edge to measure the flatness. Check the sensor for flatness in multiple (minimum 3) positions/directions. If the sensor head is distorted, replace the sensor. 8. Apply (spray) two thin coats of the specified rust penetrating lubricant (corrosion inhibitor) to the complete sensor mounting surface on the bearing hub. Allow to dry for 3-5 minutes between coats. Use ONLY Rust Penetrating Lubricant, P/N 89022217 (in Canada, P/N 89022218). 9. When the corrosion inhibitor is dry to the touch (about 10 minutes), apply a thin layer of bearing grease to the hub surface and sensor O-ring prior to sensor installation. Use ONLY Wheel Bearing Lubricant, P/N 01051344 (in Canada, P/N 993037). 10.Install either the original sensor or a new one in the hub. Ensure that the sensor is seated flush against the hub. Refer to the applicable Wheel Speed Sensor Replacement procedure in the ABS sub-section of the Service Manual. 11.Place the DVM across the sensor terminals and recheck the voltage while rotating the wheel. The voltage should now read at least 350 ACmV’s.

Related entry:

2005 highlander rear wheel bearing and speed sensor harness, mitsubishi lancer speed sensor removal, 1998 dodge caravan 3 8L speed sensor location diagrahm, mondeo mk3 snaped wheel speed sensor off in hub, speed sensor location 2002 gmc sonoma 4 wheel drive, 2006 uplander disconnect sir system, Toyota Hilux Speed Sensor Ln106 Hilux Wiring Diagram, 2002 chevy cavalier 2 2 engine speed sensors, changing a speed sensor on a 2004 kia spectra, PO793,

2004 Hyundai Sonata 2003-2004 Hyundai Santa FE 2004 Kia Optima no spark Problem and Repair

0

Filed Under (Hyundai) by admin on 25-04-2010

download
1. At the crank position sensor, check for battery voltage to be present on the Red wire with the key on and cranking. The Black wire should be a good ground and the Blue wire should have 5 volts on it from the computer. One may have to disconnect the crank sensor to check for the 5 volt reference. 2. During crank look for a good 5 volt square wave signal on the Blue wire. 3. Check at the ignition coils for good battery voltage key on and cranking. If there is a loss of voltage during crank check the ignition failsafe relay. 4. Check for any stored engine codes. Crankshaft Position (CKP) Sensor Ignition Failsafe Sensor The ignition failsafe sensor supplies battery voltage to the ignition coils. The ignition coils can look like they have good battery voltage key on but during crank the ignition failsafe relay can stop sending voltage to the ignition coils.

Related entry:

fireing order 2005 sonata 2 7, 2004 hyundai blower motor troubelshooting, 2004 hyundai santa fe repair manual online, brake job on 2004 hundsi sonaata, hyndai sonata 2004 torque plugs, HOW TO REPLACE EVAPERATOR CORE IN 2004 SORRENTO, firing order for a 2004 kia rio, 2005 hyundai sonata basic ignition coil wiring diagram 2 7, were is ecm 2004 sedona, 2004 kia sorento pcm location,