ford explorer rear bumper cover removal


You are searching repair manual in PDF format about ford explorer rear bumper cover removal use another keyword for search another post or files



  ford explorer rear bumper cover removal Direct Download speed 5787 Kb/s

  ford explorer rear bumper cover removal Full Version speed 6767 Kb/s




1996 Ford Mustang Bumper and Bumper Cover Front Removal and Installation

0

Filed Under (Ford) by admin on 16-02-2011

download
1. Drill out four license plate rivets (if required). 2. Remove fog lamps (15200) (if equipped). 3. Remove two nuts and two screws retaining front bumper (17757) to each front fender (16005). 4. Remove one screw (3 on Cobra) retaining front bumper cover (17D957) to each front fender splash shield (16102). 5. Remove three pushpins retaining front bumper cover to radiator support (16138). 6. Remove two upper blind rivets retaining front bumper cover to radiator grille opening panel reinforcement (8A284). Front Bumper Cover 7. Remove two rivets retaining front bumper cover support (17C947) to front bumper. Remove center pins from rivets using a drift punch. Remove the remainder of the rivets using a drill. Use care not to enlarge the retaining holes in the sheet metal. 8. Remove LH and RH headlamp bulbs (13007). Refer to Section 17-01. 9. Insert a thin screwdriver blade between the underside of the front bumper cover and the radiator grille opening panel reinforcement to release the front bumper cover locking tabs on both LH and RH sides, underneath the headlamp opening. Remove the front bumper cover while the lock tabs are lifted. Front Bumper Cover Removal 11. On each side of vehicle (convertible only), remove one bolt and one nut retaining front bumper vibration damper to front bumper. Front Bumper Vibration Damper—Convertible

2004 Ford F-150 Rear Axle Differential Cover Axle Shaft Oil Seal and Rear Wheel Bearing REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 28-02-2011

download
1. With the vehicle in NEUTRAL, position on a hoist. For additional information, refer to Section 100-00. 2. Remove the rear wheel and tire assembly. For additional information, refer to Section 204-00. 3. Remove the parts in the order indicated in the following illustration and table. 4. To install, reverse the removal procedure. 5. Fill the axle with the specified quantity of the specified lubricant. For additional information, refer to the Specifications in this section. Item 2: Rear Disc Brake Caliper Removal Note 1. CAUTION: Do not allow the caliper to hang from the brake hose. Provide a suitable support. Position the rear disc brake caliper aside. For additional information, refer to Section 206-00. Item 7: Differential Pinion Shaft Removal Note 1. Move the differential pinion shaft out far enough to remove the U-washers. Replace the shaft and install the lock bolt finger tight when U-washers are removed. Item 8: U-washer Removal Note 1. CAUTION: Do not damage the rubber O-rings in the axle shaft grooves. Remove the U-washers. 1. Push the axle shafts inboard. 2. Remove the U-washers. Item 10 and 11: Wheel Bearing Oil Seal and Axle Shaft Bearing Removal Note 1. CAUTION: Never remove the wheel bearing oil seal by itself. Always remove the wheel bearing oil seal and the rear wheel bearing at the same time. For the 8.8 inch rear axle, use the special tools to remove the rear wheel bearing and wheel bearing oil seal. 2. CAUTION: Never remove the wheel bearing oil seal by itself. Always remove the wheel bearing oil seal and the rear wheel bearing at the same time. For the 9.75 inch and the 10.25 inch rear axles, use the special tools to remove the rear wheel bearing and wheel bearing oil seal. Item 11: Axle Shaft Bearing Installation Note 1. For the 8.8 inch and the 9.75 inch rear axles, use the special tools to install the rear axle wheel bearing. 2. For the 10.25 inch rear axle, use the special tools shown to install the rear axle wheel bearing. Item 10: Wheel Bearing Oil Seal Installation Note 1. Use the special tools shown to install the rear wheel bearing oil seal. Item 8: U-washer Installation Note 1. CAUTION: Do not damage the rubber O-rings in the U-washer grooves. Install the U-washers. 1. Position the two U-washers on the button end of the axle shafts. 2. Pull the axle shafts outward.

2008 Mercury Mariner Rear Bumper Cover / Fascia Removal and Replacement

0

Filed Under (Mercury) by admin on 29-07-2010

download
BUMPER COVER – REAR Exploded View Removal and Installation 1. Remove the 2 rear bumper cover lower screws (1 each side). To install, tighten to 5 Nm (44 lb-in) . 2. Remove the 4 rear bumper cover center screws. 3. Remove the 2 rear bumper cover lower pushpins. 4. Remove the 2 rear splash shield-to-rear bumper cover screws (1 each side). 5. Remove the 2 rear bumper cover upper screws (1 each side). To install, tighten to 5 Nm (44 lb-in) . 6. Remove the 2 liftgate alignment bumper bolts and the 2 liftgate alignment bumpers. To install, tighten to 8 Nm (71 lb-in) . 7. Disconnect the parking aid system or trailer tow electrical connector, if equipped. 8. Remove the rear bumper cover. 9. To install, reverse the removal procedure. When installing, position the rear bumper cover into the bumper slides.

1995 Ford Thunderbird Spring REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 02-03-2011

download
Removal 1. Raise vehicle on hoist. Refer to Section 00-02. 2. Remove rear wheel and tire assembly. 3. Remove rear stabilizer bar link and bushing link nuts at both ends of rear stabilizer bar (5A772) . Rotate bar up and out of the way. 4. Disconnect parking brake rear cable and conduit (2A635) at rear disc brake caliper (2553) . 5. Install three Rotunda Spring Cages 086-00031 or equivalent to rear spring as follows: a. Install one spring cage without an adjuster link to the inboard side (the innermost “bend” of the rear spring (5560) ). b. Install two more spring cages, with adjusters, at 120 degree angles to the previously installed cage. Spring, Rear 6. Place a transmission jack or suitable stand under the rear suspension arm and bushing (5500) as far outboard as possible. 7. Support the rear wheel knuckle (5A969) assembly by wiring the rear suspension arm and bushing to the body. 8. Remove lower rear shock absorber mounting bolt, washer and nut. 9. NOTE: Rear suspension arm and bushing must not be lowered until pivot bolts are loose. Do not attempt to remove plastic cap on front pivot nut. Loosen both inboard pivot bolts on rear suspension arm and bushing . 10. Remove two bolts and nuts retaining rear suspension arm and bushing to rear wheel knuckle . 11. Lower the rear suspension arm and bushing by lowering jack. Ensure spring cages properly seat on rear spring as rear suspension arm and bushing is dropped. 12. Remove jack, lower rear suspension arm and bushing down fully by hand and remove rear spring with cages in place. 13. Remove rear spring center mounting insulators (5741) , if necessary. 14. If spring cages are to be removed for installation on rear spring , use Coil Spring Compressor D78P-5310-A or equivalent to compress rear spring and remove cages. Rear spring center mounting insulator should be installed on rear spring before installing rear spring in tool to prevent slipping of plates.

1995 Ford Windstar Engine Front Cover REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 06-04-2011

download
Engine Front Cover If the engine front cover (6019) is being removed to check timing chain deflection, refer to Timing Chain Deflection Procedure as outlined in Section 03-00. SPECIAL SERVICE TOOL(S) REQUIRED Description Crankshaft Damper Remover Vibration Damper and Seal Replacer T82L-6316-A Vibration Damper Remover Adapter Removal 1. Remove engine (6007) from vehicle. Refer to procedure in this section. 2. Loosen drive belt tensioner (6B209) and drive belt (8620) . 3. Remove water pump pulley retaining bolts and water pump pulley (8509) . 4. Remove retaining bolts and disconnect heater water outlet tube (18663) from water pump (8501) . 5. Disconnect electrical connector at camshaft position sensor. 6. Disconnect electrical connector at crankshaft position sensor (CKP sensor) (6C315) . 7. Remove retaining bolt and disconnect radiator lower hose tube (8291) from water pump . NOTE: If the vibration damper and crankshaft pulley have to be separated, mark the vibration damper and crankshaft pulley so that they may be reassembled in the same relative position. This is important as the vibration damper and crankshaft pulley are initially balanced as a unit. NOTE: If the vibration damper is being replaced, check if the original vibration damper has balance pins installed. If so, new balance pins (6A328 or equivalent) must be installed on the new vibration damper in the same position as the original vibration damper. The crankshaft pulley (new or original) must also be installed in the same relative position as originally installed. 8. Remove crankshaft pulley (6312) and vibration damper assembly using Crankshaft Damper Remover T58P-6316-D and Vibration Damper Remover Adapter T82L-6316-B. 9. Remove four retaining bolts and remove brace from A/C bracket and P/S bracket. 10. Remove oil bypass filter (6714) . Tool Number T58P-6316-D T82L-6316-B CAUTION: The engine front cover cannot be removed without lowering the oil pan (6675) . 11. Remove oil pan . Refer to procedure in this section. CAUTION: Do not overlook the engine front cover retaining bolt located behind the oil pump and filter body (6603) . The engine front cover will break if pried upon and all retaining bolts are not removed. 12. Remove engine front cover retaining bolts. It is not necessary to remove water pump . 13. Remove engine front cover and water pump as an assembly. 14. Remove engine front cover gasket and discard. Water Pump Tightening Sequence Installation NOTE: Lightly oil all bolt and stud bolt threads before installation except those specifying special sealant. 1. Clean gasket surfaces on the engine front cover and cylinder block (6010) . If reusing the engine front cover , replace crankshaft front seal (6700) . Refer to Crankshaft Pulley and/or Damper and/or Crankshaft Front Seal in this section. 2. If a new engine front cover is to be installed: Install oil pump and filter body . Clean water pump gasket surface. Position a new water pump housing gasket (8507) on the engine front cover and install water pump . Install water pump retaining bolts. Tighten to 20-30 Nm (15-22 lb-ft). 3. Lubricate crankshaft front seal with clean engine oil XO-10W30-QSP or -DSP or equivalent meeting Ford specification ESE-M2C153-E. NOTE: Gasket and Trim Adhesive D7AZ-19B508-B or equivalent meeting Ford specification ESE-M2G52-A is recommended to hold the engine front cover gasket (6020) in position while the engine front cover is installed. 4. Position a new engine front cover gasket on the cylinder block and install the engine front cover / water pump assembly using dowels for proper alignment. 5. Install the engine front cover retaining bolts. Tighten to 20-30 Nm (15-22 lb-ft). Install the capscrew (Part No. N804841) nearest the oil bypass filter flange last, and tighten last. Apply Loctite® or equivalent to bolt prior to installation. Refer to illustration under Step 13 of removal procedure. 6. Install oil pan as outlined. 7. Install oil bypass filter . 8. Coat pulley sealing surface with clean engine oil XO-10W30-QSP or -DSP or equivalent meeting Ford specification ESE-M2C153-E. NOTE: When using silicone rubber sealer, assembly must occur within 15 minutes after sealer application. After this time, the sealer may start to setup, and its sealing effectiveness may be reduced. 9. Apply a small amount of Silicone Gasket and Sealant F1AZ-19562-A or equivalent meeting Ford specification WSE-M4G320-A2 to crankshaft keyway. 10. Position crankshaft key (6B316) in the crankshaft keyway.